• Home
  • Epson Driver
  • Reset Printer
  • Error Codes
    • Epson
    • KIP
    • Kyocera
    • Mimaki
    • Minolta
    • Mutoh
    • OKI
    • Panasonic
    • Riso
    • Roland
    • Sanyo
    • Xerox
    • Zebra
  • Adjustment
  • Epson XP 15000
    • Troubleshooting
    • Assembly
    • MAINTENANCE
    • APPENDIX
  • WordPress
  • Facebook
  • Store
  • Contact Us

Nguyễn Đăng Nam's Blog

You are here: Home / ADJUSTMENT / Checking Epson XP-15000 | XP series Platen Gap

Checking Epson XP-15000 | XP series Platen Gap

April 28, 2021 by dangnam69 Leave a Comment

This section describes the procedure for checking the platen gap (PG)

 The standard range of the PG is as follows:
• Standard: 1.2 ± 0.1 mm (PG -)
 This adjustment should be carried out with the mechanism in the minimum PG position (PG -) before installing the CR Scale.
 PG changes approximately 0.08 mm by moving one notch of the parallel adjustment bushing

  • Tools:    Thickness gauge: 1.1 mm, 1.3 mm

Epson XP-15000 | XP series Platen Gap adjustment flow

Epson-XP-15000-15010-15080-Platen-Gap-adjustment-flow.jpg
Figure 1: Platen Gap adjustment flow

Before doing the Checking Epson XP15000 | XP series Platen Gap Adjustment, check the following:

  • The rib A on the CR Shaft Gear should be set vertically upward in the PG position (PG -).
  • The center of the notch of the Parallel Adjustment Bushing on the side of the printer is set in the position of the rib B.
Epson-XP-15000-15010-15080-position-Parallelism-Bush.jpg
Figure 2: Position of Parallelism Bush

How to check Epson XP-15000 | XP series Platen Gap?

Warning:

When performing the PG adjustment, make sure of the following.
– Move the CR Unit by pulling the top pf the CR Timing Belt.
– Be careful not to damage the nozzle surface of the Printhead with the thickness gauge.
– PG Adjustment should be carried out with the new ink cartridges are installed. The ink cartridges should be installed with the CR Unit is in the ink cartridge exchange position.(See Printhead (p53).)
–  To maintain the parallelism adjustment bush’s designed performance for holding the CR Guide shaft, if the bush is deformed such as being scratched with a screw mark, make sure to replace it with a new one.

Adjustment of the 0-digit side

  • STEP 1. Loosen the screws (x4) on the CR Guide Rail, the each screw securing the CR Scale Holder and CR Spacer, and the screws (x2) securing the Parallelism Adjustment Bushing on the left/right of the printer. (See Figure 2.)
  • STEP 2. Move the CR Unit to the center of the printer and place the thickness gauge (1.1 mm) on the position A shown in Figure 3.
/Epson-XP-15000-15010-15080-thickness-gauge-placement.jpg
Figure 3: Thickness Gauge placement
  • STEP 3. Move the CR Unit to the 0-digit side while pushing the CR Guide Rail from the top and check if the CR Unit touches the thickness gauge.
    • When the CR Unit touches the thickness gauge
      Move the CR Unit to the center, move the Parallelism Adjustment Bushing at the 0-digit side by one notch in the + direction. (See Figure 2.)
    • When the CR Unit does not touch the thickness gauge
      Move the CR Unit to the center, move the Parallelism Adjustment Bushing at the 0-digit side in the – direction until the CR Unit touches the thickness gauge and repeat this procedure from Step 3.
  • STEP 4. Move the CR Unit to the 0-digit side again while pushing the CR Guide Rail from the top and check if the CR Unit touches the thickness gauge.
    • When the CR Unit touches the thickness gauge
      Move the CR Unit to the center, move the Parallelism Adjustment Bushing at the 0-digit side by one notch in the + direction and repeat this procedure from Step 3. (See Figure 2)
    • When the CR Unit does not touch the thickness gauge
      Move the CR Unit to the center and go to Step 5.
  • STEP 5. Remove the thickness gauge (1.1 mm) and place the thickness gauge (1.3 mm) on the position A shown in Figure 3.
  • STEP 6. Move the CR Unit to the 0-digit side and check if the CR Unit touches the thickness gauge.
    • When the CR Unit touches the thickness gauge
      Move the CR Unit to the center and remove the thickness gauge, and secure the screw on the Parallelism Adjustment Bushing at the 0-digit side. Go to Step 7.
    • When the CR Unit does not touch the thickness gauge
      The PG is too wide, so move the CR Unit to the center of the printer and repeat this procedure from Step 2

Adjustment of the 130-digit side

  • STEP 7. Place the thickness gauge (1.1 mm) on the position B shown in Figure 3).
  • STEP 8. Move the CR Unit to the 130-digit side while pushing the CR Guide Rail from the top and check if the CR Unit touches the thickness gauge.
    • When the CR Unit touches the thickness gauge
      Move the CR Unit to the center, move the Parallelism Adjustment Bushing at the 130-digit side by one notch in the + direction. (See Figure 2.)
    • When the CR Unit does not touch the thickness gauge
      Move the CR Unit to the center, move the Parallelism Adjustment Bushing at the 130-digit side in the – direction until the CR Unit touches the thickness gauge and repeat this procedure from Step 8.
  • STEP 9. Move the CR Unit to the 130-digit side again while pushing the CR Guide Rail from the top and check if the CR Unit touches the thickness gauge.
    • When the CR Unit touches the thickness gauge
      Move the CR Unit to the center, move the Parallelism Adjustment Bushing at the 130-digit side by one notch in the + direction and repeat this procedure from Step 8. (See Figure 2)
    • When the CR Unit does not touch the thickness gauge
      Move the CR Unit to the center and go to Step 10.
  • STEP 10. Remove the thickness gauge (1.1 mm) and place the thickness gauge (1.3 mm) on the position B shown in Figure 3.
  • STEP 11. Move the CR Unit to the 130-digit side and check if the CR Unit touches the thickness gauge.
    • When the CR Unit touches the thickness gauge
      Move the CR Unit to the center and remove the thickness gauge, and secure the screw on the Parallelism
      Adjustment Bushing at the 130-digit side. Go to Step 12.
    • When the CR Unit does not touch the thickness gauge
      The PG is too wide, so move the CR Unit to the center of the printer and repeat this procedure from Step 7.

Checking the Epson XP-15000 | XP series Platen Gap

  • STEP 12. Place the thickness gauge (1.1 mm) on the position A shown in Figure 3 above.
  • STEP 13. Move the CR Unit to the 0-digit side and check if the CR Unit touches the thickness gauge.
    • When the CR Unit touches the thickness gauge
      Move the CR Unit to the center and repeat this procedure from Step 1.
    • When the CR Unit does not touch the thickness gauge
      Move the CR Unit to the center and remove the thickness gauge, and go to Step 14.
  • STEP 14. Place the thickness gauge (1.3 mm) on the position A shown in Figure 3 above.
  • STEP 15. Move the CR Unit to the 130-digit side and check if the CR Unit touches the thickness gauge.
    • When the CR Unit touches the thickness gauge
      Move the CR Unit to the center and remove the thickness gauge, and go to Step 16.
    • When the CR Unit does not touch the thickness gauge
      Move the CR Unit to the center and repeat this procedure from Step 1.
  • STEP 16. Secure the screw (x2) on the CR Guide Rail. See Pickup Assy from Epson XP 15000 remove parts: Sensors, Main Frame, Paper Guide,… click here
  • STEP 17. Remove the ink cartridges and complete the adjustment.

Bài viết liên quan

Epson-XP-15000-15010-15080-secure-star-wheel-holder-assy
Secure Epson XP 15000 | XP series after reparing
Epson-XP-15000-15010-15080-secure-CR-Assy-1
Epson XP 15000 | XP series Cable connections and Secure
Epson-XP-15000-15010-15080-lubricate-left-parallel-bushing
Lubricate Epson XP 15000 | XP series Wheel and Gear

Filed Under: ADJUSTMENT Tagged With: ADJUSTMENT, adjustment program, Epson XP-15000/XP-15010/XP-15080, printer, printer errors

About dangnam69

Information Security, Web Design, Computer Science, Printer Technician

Previous Post: « XP-15000 AdjProg initial setting and Mist Recovery check
Next Post: Epson XP 15000 | XP series Maintenance Cleaning the Printhead »

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Primary Sidebar

Your Cart

Items in Your Cart

Your cart is empty

ONLINE SUPPORT

Telegram: Đăng Miền

phone +0084 915 589 236

Nguyễn Đăng Miền    Nguyễn Đăng Miền

Telegram: Đăng Nam


Zalo: Đăng Nam
zalo

Recent Posts

  • Repair Canon MF9220Cdn Printer Error Codes Canon Servie Tool
  • Repair Canon MF8380Cdw Printer Error Codes Canon Servie Tool
  • Repair Canon MF8350Cdn Printer Error Codes Canon Servie Tool
  • Repair Canon MF8340Cdn Printer Error Codes Canon Servie Tool
  • Repair Canon MF8330Cdn Printer Error Codes Canon Servie Tool

Products

Epson Wic Key
Epson Wic Key
Fix Epson red lights blinking with errors: Service Required, A printer's ink pad at the end of its service life Please contact Epson Support. Guaranty 100% money back if it does not work (counter still 100%) !!!
Quantity:  
Price: $7.86Price: $9.99 
printer driver download free

Copyright © 2023 · All Rights Reserved - Powered Nguyễn Đăng Nam