Solved Roland ZAT650 Modela pro Error Codes
– Printer model: Roland ZAT650 Modela pro
– Error codes on Roland ZAT650 Modela pro model and its description:
– Roland ZAT650 Modela pro printer Error Codes and quick guide to troubleshooting:
- Code: n01
- Display: NO ATC UNIT
- Description: The [ATC] menu item was executed, but no ATC unit is installed.
- Troubleshooting Guides: The [ATC] menu item can be executed, only when an ATC unit is installed. After a short interval, the machine automatically returns to the original screen.
- Code: n02
- Display: NOW CATCHING TOOL ‘ENTER’ TO RELEASE
- Description: The power was switched on while a tool was in a gripped state.
- Troubleshooting Guides: When the power is switched on while a tool is gripped, the tool is released to ensure safety. Pressing the [ENTER] key immediately performs a forced release and clears the error. No operation to return the tool to the magazine is performed, so support the tool with your hand as you perform this operation to keep the tool from being dropped. (1)Press the [ENTER] key. A forced release is performed, and the message [IF TOOL IS RELEASED, THEN PUSH ‘ENTER’] appears. (2)If the tool was released, then press the [ENTER] key to clear the error. If the tool was not released, then switch off the power. Make sure the air pressure is within the specified range and that no air hoses of cables have come loose, then switch on the power. If the error message appears again, press the [ENTER] key. If this operation fails to release the tool, then contact your Roland DG Corp. service center. If this message does not appear even though a tool is grasped, then immediately switch off the power and contact your Roland DG Corp. service center.
- Code: n03
- Display: CAN’T CATCH TOOL ** SET TOOL THEN ENTER
- Description: The specified tool cannot be grasped.
- Troubleshooting Guides: Here, ‘**’ indicates the stock number. This appears when an attempt to get a tool fails because the tool is not loaded in the magazine, or is not loaded at the appropriate location in the magazine, or for similar reasons. If the tool is not loaded in the magazine, then load it and press the [ENTER] key. The machine clears the error and again performs the operation for getting the tool. If the error occurred for some other cause, then switch off the power, eliminate the cause, then carry out the procedure again.
- Code: n03
- Display: NO Z0 SENSOR SET SENSOR THEN ENTER
- Description: An attempt was made to carry out automatic measurement of tool length while the Z0 sensor was not connected.
- Troubleshooting Guides: The Z0 sensor is required in order to execute [LENGTH SCAN] (although this is not required when the rotary axis unit is installed). Connect the Z0 sensor, place it on the sensor base, then press the [ENTER] key. The machine clears the error, then restarts measurement.
- Code: n04
- Display: TOOL LENGTH TOO LONG SHORTEN IT AND ENTER
- Description: Automatic measurement cannot be performed because the tool is too long.
- Troubleshooting Guides: On executing [LENGTH SCAN], if the tool is too long and measurement cannot be performed, this message appears and the tool is returned to the magazine. Replace the tool with one of the specified length, then press the [ENTER] key. The machine clears the error, then restarts measurement.
- Code: n05
- Display: AIR PRESSURE SHORT
- Description: Operation was interrupted because the pressure of the compressed air was lower than permitted.
- Troubleshooting Guides: This appears when the pressure of the compressed air is insufficient. First, readjust the air pressure to 0.5 to 0.65 MPa. When the display changes to [‘ENTER’ TO CONTINUE], press the [ENTER] key. The error is cleared and the operation resumes.
- Code: n06
- Display: AIR PRESSURE TOO HIGH
- Description: Operation was interrupted because the pressure of the compressed air was higher than permitted.
- Troubleshooting Guides: This appears when the pressure of the compressed air is excessively high. First, readjust the air pressure to 0.5 to 0.65 MPa. When the display changes to [‘ENTER’ TO CONTINUE], press the [ENTER] key. The error is cleared and the operation resumes.
- Code: n07
- Display: OPERATING ERROR CAN’T RELEASE TOOL
- Description: The tool cannot be released.
- Troubleshooting Guides: This appears when the grasped tool could not be released for some reason. Switch off the power and make sure the air pressure is within the permitted range. Also make sure that no air hoses or cables have come loose. Switch on the power again. When [NOW CATCHING TOOL ‘ENTER’ TO RELEASE] appears, press the [ENTER] key to try performing a forced release. (Be careful not to let the tool fall at this time.) If this operation fails to release the tool, then contact your Roland DG Corp. service center.
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer
2. Press and hold the Resume/Cancel/Stop button
3. Press and hold the ON button (do not release both buttons)
4. Release the Resume/Cancel/Stop button (do not release the ON button)
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
For more information about Canon Serice Tool V5610
Contact us to get support with Roland ZAT650 Modela pro Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
