Solved Roland XR640 SolJet Pro 4 Error Codes and description

Solved Roland XR640 SolJet Pro 4 Error Codes

– Printer model: Roland XR640 SolJet Pro 4
– Error codes on Roland XR640 SolJet Pro 4 model and its description:

– Roland XR640 SolJet Pro 4 printer Error Codes and quick guide to troubleshooting:

• Code: 0002
• Description: Disorder of communication with Sub CPU This occurs when the Sub CPU is not detected after turning on the machine
• Causes: Servo Board does not work correctly. Sub CPU does not work correctly. There is a bad connection between Main Board and Servo Board.
• Troubleshooting Guides: Check cable connection between Main Board and Servo Board. Check cable connection between Main Board and Heater Board. Check the other cable connections of Servo Board Heater Board replacement Servo Board replacement Main Board replacement Flexible cable replacement

• Code: 0004
• Description: Sub CPU SRAM error
• Causes: SRAM is broken.
• Troubleshooting Guides: Servo Board replacement

• Code: 0005
• Description: An error occurs during downloading a program for sub CPU.
• Causes: Servo Board does not work correctly. Sub CPU does not work correctly. There is a bad connection between Main Board and Servo Board. A noise on a signal.
• Troubleshooting Guides: Check cable connection between Main Board and Servo Board. Check cable connection between Main Board and Heater Board. Check the other cable connections of Servo Board Heater Board replacement Servo Board replacement Main Board replacement Flexible cable replacement

• Code: 0006
• Description: An error occurs when trying to connect with sub CPU.
• Causes: A noise on a signal while sending a command. Sub CPU was reset to default. Tried to communicate when Sub CPU was reset to default.
• Troubleshooting Guides: Check cable connection between Main Board and Servo Board. Check cable connection between Main Board and Heater Board. Check the other cable connections of Servo Board Heater Board replacement Servo Board replacement Main Board replacement Flexible cable replacement

• Code: 0007
• Description: An error occurs while sending a command.
• Causes: Servo Board does not work correctly. Sub CPU does not work correctly. There is a bad connection between Main Board and Servo Board. A noise on a signal while sending a command. Sub CPU was reset while sending a command.
• Troubleshooting Guides: Check cable connection between Main Board and Servo Board. Check cable connection between Main Board and Heater Board. Check the other cable connections of Servo Board Heater Board replacement Servo Board replacement Main Board replacement Flexible cable replacement

• Code: 0008
• Description: There is a problem with synchronizing serial communication to Sub CPU.
• Causes: Servo Board does not work correctly. Sub CPU does not work correctly. There is a bad connection between Main Board and Servo Board. A noise on a signal.
• Troubleshooting Guides: Check cable connection between Main Board and Servo Board. Check cable connection between Main Board and Heater Board. Check the other cable connections of Servo Board Heater Board replacement Servo Board replacement Main Board replacement Flexible cable replacement

• Code: 0010
• Description: Network I/F Initialize has not been completed.
• Causes: Network I/F does not work correctly. Firmware for Network I/F is not installed.
• Troubleshooting Guides: Check the firmware is installed into Network I/F. Main Board replacement

• Code: 0101
• Description: Limit Position Initialize in the Service Mode has not been done.
• Causes: Limit Position Initialize has not been done. Limit Position Initialize is ended before it is completed.
• Troubleshooting Guides: Complete Limit Position Initialize correctly.

• Code: 0102
• Description: Even though the machine carries out the regular movement, the output of Head Lock Sensor does not reach the expected value.
• Causes: Head Lock Sensor does not work correctly or is broken.
• Troubleshooting Guides: Head Lock Sensor replacement Check the mechanical backlash or loose with the scan axis related parts.

• Code: 0103
• Description: Even though the machine carries out the regular movement, the output of Limit Sensor does not reach the expected value.
• Causes: Limit Sensor does not work correctly or is broken.
• Troubleshooting Guides: Limit Sensor replacement Check the mechanical backlash or loose with the scan axis related parts.

• Code: 0104
• Description: Even though the machine carries out the regular movement, the output of Capping Sensor does not reach the expected value.
• Causes: Capping Motor does not work correctly or is broken. Capping Unit does not work correctly or is broken. Capping Sensor does not work correctly or is broken.
• Troubleshooting Guides: Capping Motor replacement Capping unit replacement Capping Sensor replacement Flexible Cable replacement

• Code: 0105
• Description: Tool Carriage Connection Error
• Causes: Fault of Tool Carriage Connection Loose of Connection Part Fault of the Limit Position Initialize value Limit Sensor does not work correctly or is broken.
• Troubleshooting Guides: Check the mechanical Backlash or loose with the Tool Carriage part. Connection Part Replacement Limit Position Initialize

• Code: 0106
• Description: Machine fails to disconnect the Tool Carriage from the Head Carriage.
• Causes: Fault of Tool Carriage Connection Loose of Connection Part Fault of the Limit Position Initialize value Limit Sensor does not work correctly or is broken.
• Troubleshooting Guides: Check the mechanical Backlash or loose with the Tool Carriage part. Connection Part Replacement Limit Position Initialize

• Code: 0107
• Description: Linear Encoder Setup has not been done.
• Causes: Linear Encoder Setup has not been done. Linear Encoder Setup is ended before it is completed.
• Troubleshooting Guides: Carry out Linear Encoder Setup in service menu

• Code: 0109
• Description: Even though the machine carries out the regular movement, the output of the Wiper Sensor does not reach the expected value.
• Causes: Wiper Motor error Defect of Wiper Unit Defect of Wiper Sensor Cut-line or short-circuit of cable and Flexible cable
• Troubleshooting Guides: Wiper Motor Replacement Wiper Unit Replacement Wiper Sensor Replacement Cable and Flexible Cable Replacement

• Code: 0110
• Description: Input value from Linear Encoder is not changed by the Linear Encoder origin setup. When Motor stops during printing, expected movement is not completed on some head.
• Causes: Read error of Linear Encoder. Read error of Encoder on Scan Motor side. Belt is not fixed to Head Carriage firmly.
• Troubleshooting Guides: Confirm whether Encoder Scale is between the slit of Encoder Module in a whole width of the machine. Check cable connection between Linear Encoder Board and Head Board Confirm connection between Belt and Carriage Linear Encoder replacement Scan Motor replacement Servo Board replacement Main Board replacement

• Code: 0111
• Description: This error occurs when the machine performs the Auto Crop Mark Detection without peforming the Tool / Crop-Cut Adjustment.
• Causes: Crop-Cut Adjustment has not been performed in service menu
• Troubleshooting Guides: Carry out Crop-Cut Adjustment in service menu

• Code: 0112
• Description: It is not possible to communicate with the Cartridge IC driver.
• Causes: Cartridge IC driver has a problem (not working). The communication wire of Cartridge IC driver cable has short circuited or cut-line.
• Troubleshooting Guides: Ink cartridge IC sensor replacement

• Code: 0120
• Description: There is a problem with Thermistor for Pre-Heater.
• Causes: Thermistor Cable has short circuited or cutline. Thermistor has a problem.
• Troubleshooting Guides: Check Cable connection around Thermistor Thermistor replacement

• Code: 0125
• Description: Pre-Heater temperature has reached 60°C and above.
• Causes: Pre-Heater Cable connection has a problem. Thermostat has a problem. Thermistor has a problem.
• Troubleshooting Guides: Check Pre-Heater Check Thermostat Check Thermistor

• Code: 0130
• Description: There is a problem with Thermistor for Print Heater.
• Causes: Thermistor cable has short circuited or cutline. Thermistor has a problem.
• Troubleshooting Guides: Check Cable connection around Thermistor Thermistor replacement

• Code: 0135
• Description: Print Heater temperature has reached 60°C and above.
• Causes: Print Heater Cable connection has a problem. Thermostat has a problem. Thermistor has a problem.
• Troubleshooting Guides: Check Print Heater Check Thermostat Check Thermistor

• Code: 0140
• Description: There is a problem with Thermistor for dryer.
• Causes: Thermistor cable has short circuited or cutline. Thermistor has a problem.
• Troubleshooting Guides: Check Cable connection around Thermistor Thermistor replacement

• Code: 0145
• Description: Dryer temperature has reached 80°C and above.
• Causes: Dryer cable connection has a problem. Thermostat has a problem. Thermistor has a problem.
• Troubleshooting Guides: Check Dryer Check Thermostat Check Thermistor

• Code: 0146
• Description: Option Dryer temperature has reached 80°C and above.
• Causes: Option Dryer cable connection has a problem. Thermostat has a problem. Thermistor has a problem.
• Troubleshooting Guides: Check Option Dryer Check Thermostat Check Thermistor

• Code: 0250
• Description: Head device has detected a problem.
• Causes: Cut-line or short-circuit of cable and Flexible cable. The head is broken.
• Troubleshooting Guides: Pull out and insert the flexible cables again. Replace the flexible cable. Replace the head.

About Canon Servie Tool V5610

– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.

– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.

Canon Service Tool V5610 Functions

– Fix Canon printer 7 times/ 8 times red light blinking:

– Fix Canon printer error code: 5B00, 5B01, 1700, 1701

Enter Service Mode on Canon Printer

1. Turn off a printer
2. Press and hold the Resume/Cancel/Stop button
3. Press and hold the ON button (do not release both buttons)
4. Release the Resume/Cancel/Stop button (do not release the ON button)
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.

For more information about Canon Serice Tool V5610

Contact us to get support with Roland XR640 SolJet Pro 4 Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/