Solved Roland MDX20 Modela Error Codes
– Printer model: Roland MDX20 Modela
– Error codes on Roland MDX20 Modela model and its description:
– Roland MDX20 Modela printer Error Codes and quick guide to troubleshooting:
- Code: n01
- Display: VIEW LED becomes ON
- Description: The operation is paused. – Press the VIEW key to cancel the View state.
- Causes:
- Code: n02
- Display: MODELING MODE LED blinks in an interval of 0.1sec. SCANNING LED blinks in an interval of 0.1sec.
- Description: Command Error SIO Error
- Causes: Command cannot be recongnized. Serial Port Over-run Error. – First turn on the computer, then turn on MODELA. – Switch off the power, then check the cable connections and the port setting for the driver.
- Code: n03
- Display: Model LED blinks in an interval of 0.5sec.
- Description: Spindle Lock Error
- Causes: Too much load on the Spindle Motor. – Check the Cutter is not broken. – Select the suitable Engraving Parameters for the material.
- Code: n04
- Display: All LEDs blink in an interval of 0.5sec.
- Description: Z UNIT ERROR
- Causes: Z UNIT cannot be recongnized whether it is a SCAN UNIT or SPINDLE UNIT. The code comes loose from the SCAN UNIT or SPINDLE UNIT. – Reconnect the code.
- Code: n05
- Display: VIEW LED blinks in an interval of 1sec.
- Description: The Front Cover is detached. – Install the Front Cover. When a sensor unit is installed, the VIEW LED does not blink.
- Causes:
- Code: n06
- Display: Scan LED blinks in a sequence of ON (0.1sec) -> OFF (0.1sec) -> ON (0.1sec) -> OFF (0.3sec).
- Description: R.A.P.S. Error
- Causes: Auto-Tuning Error or Voltage is too low. – Switch off the power, then clean the Sensor. If the error is still exist, the Sensor Unit is defective.
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer
2. Press and hold the Resume/Cancel/Stop button
3. Press and hold the ON button (do not release both buttons)
4. Release the Resume/Cancel/Stop button (do not release the ON button)
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
For more information about Canon Serice Tool V5610
Contact us to get support with Roland MDX20 Modela Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
