Repair Canon NP6045 Printer Error Codes Canon Servie Tool
– Printer model: Canon NP6045
– Error codes on Canon NP6045 model and its description:
– Canon NP6045 printer Error Codes and quick guide to troubleshooting:
- Code: E000
- Description: Fuser did not heat up. Lamp, thermal switch, thermistors, connections, AC driver, DC controller, SSR, etc.
- Code: E001
- Description: Fuser temperature too high. Same possibilities as E000, as well as shorted wire.
- Code: E002
- Description: Fuser temperature not rising at correct pace, same possibilities as E000.
- Code: E003
- Description: Fuser temperature drops. Same as E000.
- Code: E004
- Description: Fuser problem: AC driver, SSR bad, wire shorted.
- Code: E005
- Description: Fuser cleaning web, or problem with sensor, lever or connector. Service mode 6 is the probably reset for this.
- Code: E006
- Description: Fuser feed connector.
- Code: E010
- Description: Drive problem. Main motor, gears, etc.
- Code: E013
- Description: Waste toner drive problem, or waste toner sensor switch has been actuated too many times.
- Code: E015
- Description: Pickup motor power supply. Could be bad motor or motor board, or DC controller.
- Code: E020
- Description: Problem with developer unit, toner hopper, hopper motor, connection, sensor or DC controller.
- Code: E030
- Description: Total counter.
- Code: E031
- Description: Option counter or total counter.
- Code: E050
- Description: Holding tray (duplex) home position sensor motor or board.
- Code: E051
- Description: Holding tray (duplex) home sensor motor or board.
- Code: E202
- Description: Panel locked up, but might be no code, scan motor problem.
- Code: E203
- Description: Scan problem or scan sensor
- Code: E204
- Description: Scan problem or scan sensor
- Code: E210
- Description: Lens sensor or motor problem
- Code: E212
- Description: Lens sensor or motor problem
- Code: E213
- Description: Scan lock sensor or lock solenoid
- Code: E220
- Description: Exposure lamp regulator board
- Code: E240
- Description: DC controller or composite power supply problem.
- Code: E243
- Description: DC controller
- Code: E400
- Description: RDF to copier communication problem
- Code: E401
- Description: RDF pickup motor or pickup sensor.
- Code: E402
- Description: RDF belt motor or pulse sensor.
- Code: E403
- Description: RDF feed motor or pulse sensor.
- Code: E411
- Description: RDF tray sensor or registration sensor
- Code: E500
- Description: Sorter main board or communication with copier
- Code: E510
- Description: Sorter feed motor
- Code: E522
- Description: Sorter push bar motor
- Code: E523
- Description: Sorter reference wall motor
- Code: E524
- Description: Sorter multi-guide motor
- Code: E525
- Description: Sorter bin paper sensor automatic adjustment problem
- Code: E526
- Description: Sorter bin paper sensor automatic adjustment problem
- Code: E530
- Description: Sorter guide bar motor
- Code: E531
- Description: Sorter stapler motor
- Code: E532
- Description: Stapler motor
- Code: E533
- Description: Stapler inside paper sensor
- Code: E540
- Description: Sorter bin shift motor
- Code: E550
- Description: Sorter power supply
- Code: E710
- Description: DC controller
- Code: E711
- Description: DC controller
- Code: E712
- Description: Document feeder IC failure
- Code: E713
- Description: DC controller, sorter
- Code: E800
- Description: Auto power off circuit problem. Main switch or DC controller.
- Code: E802
- Description: Auto power off circuit problem. Main switch or DC controller
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-g6020-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-wf-7840-driver-firmware-and-manuals/
Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html
Contact us to get support with Canon NP6045 Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
