Repair Canon NP6085 Printer Error Codes Canon Servie Tool
– Printer model: Canon NP6085
– Error codes on Canon NP6085 model and its description:
– Canon NP6085 printer Error Codes and quick guide to troubleshooting:
- Code: E000
- Description: After power-on, the upper fixing roller does not reach 100 C within 5 min.
- Code: E001
- Description: The temperature of the upper fixing roller exceeds 230 C for 5 sec or more.
- Code: E002
- Description: After the temperature of the upper fixing roller has exceeded 100 C, it does not reach 180 C within 5 min.
- Code: E003
- Description: After the temperature of the upper fixing roller has reached 180 C, it drops to 100 C or less for 5 sec or more.
- Code: E005
- Description: The length used of the cleaning belt inside the fixing assembly has exceeded a specific value.
- Code: E012
- Description: After the drum motor drive signal has been generated, clock pulses are not generated within 2 sec.
- Code: E013
- Description: After the waste toner feeding screw has become locked, the detecting switch (SW20) is pressed a multiple number of times within a specific period of time.
- Code: E014
- Description: When the fixing motor (M17) is rotating, an error is detected for 2 sec or more.
- Code: E015
- Description: After the pick up motor drive signal has been generated, clock pulses have not been generated within 2 sec.
- Code: E019
- Description: As many as 50,000 have been made after detecting a waste toner full condition.
- Code: E020
- Description: During copying, the toner supply signal is 0′, indicating the absence of toner, for 3 min or more. During toner supply sequence at time of installation, the toner supply signal does not go ‘1’ after 6 min or more.
- Code: E030
- Description: After the total copy counter has turned OFF, an open circuit is detected for the total copy counter.
- Code: E032
- Description: After the clock pulse signal reached the IPC communication format of the copier DC controller PCB, the Copy Data Controller-A1 does not detect the signal.
- Code: E050
- Description: While the paper jogging guide motor (M11) drive signal is being generated, the paper guide home position signal (THP) is not generated for 2 sec or more. While the paper jogging guide motor (M11) is being generated, the paper jogging guide home position signal (THP) is generated for two sec or more.
- Code: E202
- Description: The scanner home position signal (SCHP) is not generated within 10 sec after the power switch or the Copy Start Key is pressed.
- Code: E203
- Description: While the scanner motor drive signal is being generated, clock pulses are not generated within 2 sec.
- Code: E204
- Description: The scanner leading edge signal (SCDP1) is not generated within 0.8 sec after the scanner has started to move
- Code: E209
- Description: The scanner C.F.F. position signal (SCFFP) is not generated within 10 sec after the C.F.F. has been sent.
- Code: E210
- Description: The lens X home position signal (SCFFP) is not generated within 10 sec after the C.F.F. has been sent.
- Code: E212
- Description: The lens Y home position signal (LYHP) is not generated within 9 sec after the power switch or the Copy Start Key is turned ON. The lens Y home position signal (LYHP) is generated for 2 sec or more.
- Code: E213
- Description: In stream reading mode, the scanner original leading edge sensor 2 signal (SCDP2) is not generated for 5 pages continuously.
- Code: E214
- Description: While the scanner cooling fan (FM1, FM10, FM11) is rotating, an error signal is generated for 2 sec or more.
- Code: E270
- Description: In stream reading mode, the scanner leading edge signal(SCDP2) is not generated within a specific period of time after a command has been issued to lock the scanner.
- Code: E710
- Description: At power-on the IPC (Q170) on the DC controller PCB cannot be initialized.
- Code: E711
- Description: After power-on the IPC (Q170) on the DC controller PCB goes out of order.
- Code: E712
- Description: The communication IC on the RDF controller PCB has gone out of order.
- Code: E713
- Description: The communication IC on the sorter control PCB has gone out of order.
- Code: E715
- Description: The communication IC on the C.F.F. controller PCB has gone out of order.
- Code: E717
- Description: The communication IC on the Copy Data Controller-A1 PCB has gone out of order.
- Code: E800
- Description: An open circuit is detected
- Code: E801
- Description: Current flows from the activation circuit in the absence of the scanning lamp ON signal.
- Code: E802
- Description: The relay (RL3) in the power supply unit does not operate in spite of the auto power-off signal.
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-g3260-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-wf-8590-driver-firmware-and-manuals/
Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html
Contact us to get support with Canon NP6085 Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
