FIX Epson XP 15000 15010 15080 STK PID errors

My next post fix Fix Epson XP15000 error message code 031001,.. 202602. click here to see the guide

Beside the printer is getting error with I/S PID, it’s also getting error with STK PID.

In this post, i’m going to share my knowledge about fixing all the error that concern to Epson XP 15000 15010 15080 STK PID error code: 000140, 000141, 000142 ,000143, 000144,  000150, 000151, 000152, 000153.

You may have to remember the way the printer Epson XP 15000 15010 15080 machines display the error codes with their message errors in the following picture, let’s see and check the error to get how to fix the error.

Fix Epson XP 15000, 15010, 15080: error code 000140

STK PID driving time error

• Error code: 000140
• Error name: STK PID driving time error
• Possible cause:  Malfunction or crash of the firmware.
• Solution and how to fix Epson XP 15000, 15010, 15080 I/S  PID error code 000140?
  1.  Turn the printer off and back it on.
  2.  If the error still occurs after the restart, replace the Main Board.

Fix Epson XP 15000, 15010, 15080: error code 000141

STK PID excess load error

• Connector board: ‘Sub Board CN22, CN25’
• Error code: 000140
• Error name: STK PID excess load error
• Possible cause:
  • #The Stacker Motor stopped running in the middle of the operation.
    1. The Stacker was stopped by;
  • #Overload of the STK Assy
  • #Disengaging or breakage of the gear
  • #Failure of Stacker Encoder reading
    2. Contamination of the Stacker Encoder Scale
    3. Disconnection, break, skew or damage of the Stacker Motor Cable/Stacker Encoder FFC
    4. Failure of the Stacker Motor (not completely broken)
    5. Failure of the Main Board
• Solution and how to fix Epson XP 15000, 15010, 15080 I/S  PID error code 000140?
  1.  Check the load applied to the Stacker Assy by moving it by hand.
  2.  Check the Wheel Train of the Stacker Assy Drive for disengage or crack.
  3.  Clean the Stacker Encoder Scale if it is contaminated.
  4.  Check the cable/FFC of Stacker Motor/Encoder.
  5.  Replace the Stacker Motor with a new one.
  6.  Replace the Main Board with a new one.

Fix Epson XP 15000, 15010, 15080: error code 000142

STK PID excess speed error

• Connector board: ‘Sub Board CN22, CN25’
• Error code: 000142
• Error name: STK PID excess speed error
• Possible cause:
  • #Failure of Stacker Encoder reading
    1. Contamination of the Stacker Encoder Scale
    2. Damage or skew of the Stacker Motor Cable/
    Stacker Encoder FFC
    3. Failure of the Stacker Encoder Sensor
  • #Failure of the Stacker Motor Driver
    4. Failure of the Main Board
• Solution and how to fix Epson XP 15000, 15010, 15080 I/S  PID error code 000142?
  1.  Clean the Stacker Encoder Scale if it is contaminated.
  2.  Check the Stacker Encoder FFC or the connector.
  3.  Replace the Stacker Encoder Sensor with a new one.
  4.  Replace the Main Board with a new one.

Fix Epson XP 15000, 15010, 15080: error code 000143

STK PID reverse error

• Connector board: ‘Sub Board CN22, CN25’
• Error code: 000143
• Error name: STK PID reverse error
• Possible cause:
  • #Operation failure of the Stacker Motor, interruptedby obstacles
    1. The Stacker was stopped by;
  • #Overload of the STK Assy
  • #Disengaging or breakage of the gears
  • #Failure of Stacker Encoder reading
    2. Contamination of the Stacker Encoder Scale
    3. Damage or skew of the Stacker Motor Cable/Stacker Encoder FFC.
    4. Failure of the Stacker Encoder Sensor
    5. Failure of the Main Board
• Solution and how to fix Epson XP 15000, 15010, 15080 I/S  PID error code 000143?
  1.  Check the load applied to the STK Assy by moving it by hand.
  2.  Check the Wheel Train of the STK Assy Drive for tooth breakage or disengaging.
  3. Clean the Stacker Encoder Scale if it is contaminated.
  4. Check the cable/FFC of Stacker Motor/ Encoder.
  5. Replace the Stacker Encoder Sensor with a new one.
  6. Replace the Main Board with a new one.

Fix Epson XP 15000, 15010, 15080: error code 000144

STK PID lock error

• Connector board: ‘Sub Board CN22, CN25’
• Error code: 000144
• Error name: STK PID lock error
• Possible cause:
  • # The Stacker Motor did not run.
    1. The Stacker was stopped by;
  • # Overload of the STK Assy
  • # Disengaging or breakage of the gears
  • # Failure of Stacker Encoder reading
    2. Contamination of the Stacker Encoder Scale
    3. Break, skew or damage of the Stacker Motor Cable/Stacker Encoder FFC
    4. Failure of the Stacker Encoder Sensor
    5. Failure of the Stacker Motor (the lead wire is broken or the connector is disconnected)
    6. Failure of the Main Board
• Solution and how to fix Epson XP 15000, 15010, 15080 I/S  PID error code 000144?
  1.  Check the load applied to the STK Assy by moving it by hand.
  2.  Check the Wheel Train of the STK Assy Drive for tooth breakage or disengaging.
  3.  Clean the Stacker Encoder Scale if it is contaminated.
  4.  Check the cable/FFC of Stacker Motor/ Encoder.
  5.  Replace the Stacker Encoder Sensor with a new one.
  6.  Replace the Stacker Motor with a new one.
  7.  Replace the Main Board with a new one.

Fix Epson XP 15000, 15010, 15080: error code 000150

STK load position driving time error

• Error code: 000150
• Error name: STK load position driving time error
• Possible cause:  Malfunction or crash of the firmware
• Solution and how to fix Epson XP 15000, 15010, 15080 I/S  PID error code 000150?
  1.  Turn the printer off and back it on.
  2.  If the error still occurs after the restart, replace the Main Board

Fix Epson XP 15000, 15010, 15080: error code 000151

STK load position excess load error

• Connector board: ‘Sub Board CN22, CN25’
• Error code: 000151
• Error name: STK load position excess load error
• Possible cause:
  • #The Stacker Motor stopped running in the middle of the operation.
    1. The Stacker was stopped by;
  • #Overload of the STK Assy
  • #Disengaging or breakage of the gears
  • #Failure of Stacker Encoder reading
    2. Contamination of the Stacker Encoder Scale
    3. Break, skew or damage of the Stacker Motor Cable/Stacker Encoder FFC
    4. Failure of the Stacker Motor (not completely broken)
    5. Failure of the Main Board
• Solution and how to fix Epson XP 15000, 15010, 15080 I/S  PID error code 000151?
  1.  Check the load applied to the STK Assy by moving it by hand.
  2.  Check the Wheel Train of the STK Assy Drive for tooth breakage or disengaging.
  3.  Clean the Stacker Encoder Scale if it is contaminated.
  4.  Check the cable/FFC of Stacker Motor/Encoder.
  5.  Replace the Stacker Motor with a new one.
  6.  Replace the Main Board with a new one.

Fix Epson XP 15000, 15010, 15080: error code 000152

STK load position excess speed error

• Connector board: ‘Sub Board CN22, CN25’
• Error code: 000152
• Error name: STK load position excess speed error
• Possible cause:
  • #Failure of Stacker Encoder reading
    1. Contamination of the Stacker Encoder Scale
    2. Damage or skew of the Stacker Motor Cable/Stacker Encoder FFC
    3. Failure of the Stacker Encoder Sensor
  • #Failure of the Stacker Motor driver
    4. Failure of the Main Board
• Solution and how to fix Epson XP 15000, 15010, 15080 I/S  PID error code 000152?
  1.  Clean the Stacker Encoder Scale if it is contaminated.
  2.  Check the Stacker Encoder FFC or the connector.
  3.  Replace the Stacker Encoder Sensor with a new one.
  4.  Replace the Main Board with a new one.

Fix Epson XP 15000, 15010, 15080: error code 000153

STK load position reverse error

• Connector board: ‘Sub Board CN22, CN25’
• Error code: 000153
• Error name: STK load position reverse error
• Possible cause:
  • #Operation failure of the Stacker Motor, interrupted by obstacles
    1. The Stacker was stopped by;
  • #Overload of the STK Assy
  • #Disengaging or breakage of the gears
  • #Failure of Stacker Encoder reading
    2. Contamination of the Stacker Motor Encoder Scale
    3. Damage or skew of the Stacker Motor Cable/Stacker Encoder FFC
    4. Failure of the Stacker Encoder Sensor
    5. Failure of the Main Board
• Solution and how to fix Epson XP 15000, 15010, 15080 I/S  PID error code 000153?
  1.  Check the load applied to the STK Assy by moving it by hand.
  2.  Check the Wheel Train of the STK Assy Drive for tooth breakage or disengaging.
  3.  Clean the Stacker Encoder Scale if it is contaminated.
  4.  Check the cable/FFC of Stacker Motor/Encoder.
  5.  Replace the Stacker Encoder Sensor with a new one.
  6.  Replace the Main Board with a new one.

With my way, you can be a engineer from reading and taking this documents and fixing your own Epson XP-15000,15010,15080 printer machine.

But not just that, not only STK PID errors, you can meet very more error message code. Click here to check it out and my solution