Solved Roland CX400 Camm-1 pro Error Codes
– Printer model: Roland CX400 Camm-1 pro
– Error codes on Roland CX400 Camm-1 pro model and its description:
– Roland CX400 Camm-1 pro printer Error Codes and quick guide to troubleshooting:
- Code: 0001
- Description: Occurs when the Motor can not be controlled.
- Causes: The Output Voltage(41v) from the Switching Power Unit is not supplied. The Power Cable is not connected correctly. / The Powe Cable is broken. The Motor Driver IC on the Main Board is broken.
- Troubleshooting Guides: Replace the Switching Power Unit. Connect the Power Cable again. / Replace the Power Cable.
- Code: 0004
- Description: Occurs when the big current is flowed during acceleration in the Feed Direction.
- Causes: When the cutting starts without the Pre-feed, it occurs the over load because the Roll-sheet is pulled from the Shaft. The heavy sheet, such as the Sand Blast is used with the normal or high-speed mode. The movement of the Grit Roller is heavy because of the over load.
- Troubleshooting Guides: Turn on the Power Switch again. And then, perform the pre-feed before the cutting. Use the Heavy mode or reduce the VS value. Turn off the Power Switch and find the factor, such as fragments of the sheet, the break of the Motor or the Bearing. Then, make sure that you turn off the Power Switch and disconnect the Cable of the Y Motor before checking.
- Code: 0008
- Description: Occurs when the big current is flowed during the stable movement in the Feed Direction.
- Causes: When the cutting starts without the Pre-feed, it occurs the over load because the Roll-sheet is pulled from the Shaft. The heavy sheet, such as the Sand Blast is used with the normal or high-speed mode. The movement of the Grit Roller is heavy because of the over load.
- Troubleshooting Guides: Turn on the Power Switch again. And then, perform the pre-feed before the cutting. Use the Heavy mode or reduce the VS value. Turn off the Power Switch and find the factor, such as fragments of the sheet, the break of the Motor or the Bearing. Then, make sure that you turn off the Power Switch and disconnect the Cable of the Y Motor before checking.
- Code: 0040
- Description: Occurs when the big current is flowed during acceleration in the Carriage Direction.
- Causes: The sheet is jammed. The movement of the Tool Carriage is heavy because of the over load.
- Troubleshooting Guides: Set the sheet correctly without the slack. Turn off the Power Switch and find the factor, such as fragments of the sheet, the break of the Motor. Then, make sure that you turn off the Power Switch and disconnect the Cable of the X Motor before checking.
- Code: 0080
- Description: Occurs when the big current is flowed during the stable movement in the Carriage Direction.
- Causes: The sheet is jammed. The movement of the Tool Carriage is heavy because of the over load.
- Troubleshooting Guides: Set the sheet correctly without the slack. Turn off the Power Switch and find the factor, such as fragments of the sheet, the break of the Motor. Then, make sure that you turn off the Power Switch and disconnect the Cable of the X Motor before checking.
- Code: 2000
- Description: DDA Communication Error.
- Causes: The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error.
- Troubleshooting Guides: Replace the Main Board.
- Code: 4000
- Description: Command Communication Error.
- Causes: The communication error occurs when the IC4 or IC22 on the Main Board is broken. And it causes the Motor Error.
- Troubleshooting Guides: Replace the Main Board.
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer
2. Press and hold the Resume/Cancel/Stop button
3. Press and hold the ON button (do not release both buttons)
4. Release the Resume/Cancel/Stop button (do not release the ON button)
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
For more information about Canon Serice Tool V5610
Contact us to get support with Roland CX400 Camm-1 pro Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
