Solved Roland CT304 Camm-1 pro Error Codes
– Printer model: Roland CT304 Camm-1 pro
– Error codes on Roland CT304 Camm-1 pro model and its description:
– Roland CT304 Camm-1 pro printer Error Codes and quick guide to troubleshooting:
- Code: –
- Display: OFF-SCALE
- Description: Data sent has exceeded the effective area.
- Troubleshooting Guides: Reduce the size of data so that it falls within the effective area.
- Code: –
- Display: DATA RECEIVED DURING COPYING!
- Description: Another data is received during the execution of copying.
- Troubleshooting Guides: Re-send data from the host computer after the completion of copying.
- Code: 00
- Display: ERROR 00 MAIN ROM
- Description: Hash check error has arisen on the main ROM.
- Troubleshooting Guides: Replace the CPU circuit board with a new one.
- Code: 01
- Display: ERROR 01 SERVO ROM
- Description: Abnormal handshaking (no response) has occurred onthe Sub CPU.
- Troubleshooting Guides: Replace the SUB CPU with a proper one.(In the case of socket type) Replace the CPU circuit board with a new one.
- Code: 02
- Display: ERROR 02 MAIN RAM
- Description: Read/write error has arisen on the main RAM.
- Troubleshooting Guides: Replace the CPU circuit board with a new one.
- Code: 04
- Display: ERROR 04 EEPROM
- Description: Hash check error has arisen on the EEPROM. (Hash check is performed for the system parameter area.)
- Troubleshooting Guides: Initialize the EEPROM. 1: Turn the power on with the [<], [>] held pressed. 2: Record all the parameters. 3: Execute the initialization of the parameters. 4: If the parameters recorded are correct, re-establish them. 5: If the error should recur even after the parameters have been reestablished, replace the CPU circuit board with a new one.
- Code: 06
- Display: ERROR 06 BUFFER
- Description: Receiving buffer is in abnormal conditions.
- Troubleshooting Guides: Replace the CPU circuit board with a new one.
- Code: 08
- Display: ERROR 08 POWER
- Description: Supply voltage for driving the motor is abnormal.
- Troubleshooting Guides: Check the supply voltage. Replace the power circuit board with a new one. Replace the driver circuit board with a new one.
- Code: 10
- Display: ERROR 10 COMMAND
- Description: Unbreakable command code is received
- Troubleshooting Guides: Check the communication conditions. Perform a loopback test to check whether the device normally operates. If the device maloperates, replace the CPU circuit board with a new one.
- Code: 11
- Display: ERROR 11 PARAMETER
- Description: A parameter that is outside the specified range of values is received.
- Troubleshooting Guides: Check the communication conditions. Perform a loopback test to check whether the device normally operates. If the device maloperates, replace the CPU circuit board with a new one.
- Code: 12
- Display: ERROR 12 DEVICE
- Description: Cutting (plotting) cannot be initiated since an amount of data exceeding the capacity of the receiving buffer is sent from thehost computer and no plot start command is present in the receiving buffer. Device command is abnormal.
- Troubleshooting Guides: Check the communication conditions. Perform a loopback test to check whether the device normally operates. If the device maloperates, replace the CPU circuit board with a new one. Send an amount of data within the capacity of the receiving buffer from the host computer. If the device normally operates with the data, check the host computer. Check the communication conditions. Perform a loopback test to check whether the device normally operates. If the device maloperates, replace the CPU circuit board with a new one.
- Code: 13
- Display: ERROR 13 POLYGON
- Description: Polygon data sent exceeds the capacity of polygon buffer.
- Troubleshooting Guides: Reduce the amount of polygon data.
- Code: 20
- Display: ERROR 20 I/O
- Description: Energizing has been carried in a wrong order. Communication conditions are defective.
- Troubleshooting Guides: Turn off first the power to the plotter and host computer. Then, turn on the power to the host computer. Finally, turn on the power to the plotter. Check the communication conditions. Perform a loopback test to check whether the device normally operates. If the device maloperates, replace the CPU circuit board with a new one.
- Code: 23
- Display: ERROR 23 LOOPBACK S
- Description: Signal line is in abnormal conditions.
- Troubleshooting Guides: Connect the loopback connector. Replace the CPU circuit board with a new one.
- Code: 24
- Display: ERROR 24 LOOPBACK R
- Description: No interruption takes place in data receiving.
- Troubleshooting Guides: Connect the loopback connector. Replace the CPU circuit board with a new one.
- Code: 25
- Display: ERROR 25 LOOPBACK T
- Description: No interruption takes place during data sending.
- Troubleshooting Guides: Connect the loopback connector. Replace the CPU circuit board with a new one.
- Code: 26
- Display: ERROR 26 LOOPBACK D
- Description: Data received is defective.
- Troubleshooting Guides: Connect the loopback connector. Replace the CPU circuit board with a new one.
- Code: 30
- Display: ERROR 30 OPERATION
- Description: An erroneous operation has been taken (such that SELF TEST is executed while the device is engaged in self test or COPY is executed while the device is engaged in copying).
- Troubleshooting Guides: Point out the wrong operation. Replace the keyboard with a new one. Replace the CPU circuit board with a new one.
- Code: 31
- Display: ERROR 31 NO DATA
- Description: No data is present in the receiving buffer though ‘COPY’ operation is executed.
- Troubleshooting Guides: Explain the user that ‘COPY’ is only effective when data is present in the receiving buffer.
- Code: 32
- Display: ERROR 32 TOO LARGE
- Description: COPY has been executed after receiving data of which amount exceeds the capacity of the receiving buffer.
- Troubleshooting Guides: Explain the user that ‘COPY’ of data of which amount exceeds the capacity of the receiving buffer is not permitted.
- Code: 40
- Display: ERROR 40 X OVERLOAD
- Description: Load applied to servo-motor X has increased to an abnormal level.
- Troubleshooting Guides: Replace the servo-motor X with a new one. Replace the CPU circuit board with a new one. Replace the driver circuit board with a new one.
- Code: 41
- Display: ERROR 41 Y OVERLOAD
- Description: Load applied to servo-motor Y has increased to an abnormal level.
- Troubleshooting Guides: Replace the servo-motor Y with a new one. Replace the CPU circuit board with a new one.
- Code: 42
- Display: ERROR 42 X OVERCURRENT
- Description: Overcurrent error of servo-motor X has been detected. (The mean current exceeds the rated current of the motor.)
- Troubleshooting Guides: Replace the servo-motor X with a new one. Replace the CPU circuit board with a new one. Replace the driver circuit board with a new one.
- Code: 43
- Display: ERROR 43 Y OVERCURRENT
- Description: Overcurrent error of servo-motor Y has been detected. (The mean current exceeds the rated current of the motor.)
- Troubleshooting Guides: Replace the servo-motor Y with a new one. Replace the CPU circuit board with a new one. Replace the driver circuit board with a new one.
- Code: 46
- Display: ERROR 46 PEN SENSOR
- Description: FPC circuit board is improperly positioned. Head circuit board is defective. CPU circuit board is defective
- Troubleshooting Guides: Properly re-position the FPC circuit board. Replace the head circuit board with a new one. Replace the CPU circuit board with a new one. Replace the driver circuit board with a new one.
- Code: 50
- Display: ERROR 50 X-SENSOR
- Description: X-sensor is defective. Light shielding plate has been improperly installed. Cable has disconnected. CPU circuit board is defective.
- Troubleshooting Guides: Replace the X-sensor with a new one. Re-install the light shielding plate properly. Replace the cable and the connector respectively with a new one. Replace the CPU circuit board with a new one. Replace the driver circuit board with a new one.
- Code: 51
- Display: ERROR 51 Y SENSOR
- Description: Y-sensor is defective. Light shielding plate has been improperly installed. Cable has disconnected. CPU circuit board is defective.
- Troubleshooting Guides: Replace the Y-sensor with a new one. Re-install the light shielding plate properly. Replace the cable and the connector respectively with a new one. Replace the CPU circuit board with a new one. Replace the driver circuit board with a new one.
- Code: 52
- Display: ERROR 52 O-ORIGIN
- Description: O-axis origin detection failure
- Troubleshooting Guides: Check the origin label. Check the origin sensor. Replace the driver circuit board with a new one.
- Code: 53
- Display: ERROR 53 Z-ORIGIN
- Description: Z-axis travel cannot be performed.
- Troubleshooting Guides: Check the vertical motion of the cutter and roller.
- Code: 62
- Display: ERROR 62 VACUUM/TILT
- Description: Thermal relay is fed with an overcurrent. Faulty blower.
- Troubleshooting Guides: Check the installation of the thermal relay. Replace the blower with a new one.
- Code: 70
- Display: ERROR 70 O-OVERLOAD
- Description: Load applied to O-axis motor has increased to an abnormal level.
- Troubleshooting Guides: Inspect the O-axis speed-reduction components. Replace the CPU circuit board with a new one. Replace the head circuit board and driver circuit board.
- Code: 71
- Display: ERROR 71 O-OVERCURRENT
- Description: Overcurrent error on O-axis motor
- Troubleshooting Guides: Inspect the O-axis speed-reduction components. Replace the CPU circuit board with a new one. Replace the head circuit board and driver circuit board.
- Code: 72
- Display: ERROR 72 CUTTER Z LOAD
- Description: Load applied to Z-axis motor has increased to an abnormal level.
- Troubleshooting Guides: Replace the CPU circuit board with a new one. Replace the head circuit board and driver circuit board.
- Code: 73
- Display: ERROR 73 ROLLER Z LOARD
- Description: Load applied to Z-axis motor of marking roller has increased to an abnormal level.
- Troubleshooting Guides: Replace the CPU circuit board with a new one. Replace the driver circuit board with a new one.
- Code: 75
- Display: ERROR 75 SUM CHECK
- Description: A sum check mismatch has occurred in the firmware read.
- Troubleshooting Guides: Start over the version updating. Change the version up file.
- Code: 80
- Display: ERROR 80 FORMAT
- Description: An improper version up file is used.
- Troubleshooting Guides: Obtain the correct version up file to try to update the version again.
- Code: 90
- Display: ERROR 90 F / W
- Description: Sub CPU fault.
- Troubleshooting Guides: Replace the CPU circuit board with a new one.
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer
2. Press and hold the Resume/Cancel/Stop button
3. Press and hold the ON button (do not release both buttons)
4. Release the Resume/Cancel/Stop button (do not release the ON button)
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
For more information about Canon Serice Tool V5610
Contact us to get support with Roland CT304 Camm-1 pro Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
