Solved Roland CS540 SolJet proII Error Codes
– Printer model: Roland CS540 SolJet proII
– Error codes on Roland CS540 SolJet proII model and its description:
– Roland CS540 SolJet proII printer Error Codes and quick guide to troubleshooting:
- Code: 0001
- Description: Feed Motor Deviation Error
- Causes: < User side > 1. Media Jam 2. Pull or Move the Carriage by hand. 3. Carriage runs into a thing/hands. 4. Media is stuck because the media end is not separated from the paper tube. 5. Heavy media is used. < Mechanical Side > 1. There is a bad contact/cut-line in the cable. 2. Screw fixing the tool carriage to wire is shifted. 3. Motor is broken./Life 4. Head/Servo Board is broken.
- Troubleshooting Guides:
- Code: 0002
- Description: Sub CPU Communication Error
Disorder of communication with Sub CPU - Causes: Sub Board does not work correctly. Sub CPU does not work correctly. There is a bad connection between Main Board and Sub Board.
- Troubleshooting Guides: 1) Check Cable Connection between Main Board and Servo Board 2) Servo Board Replacement 3) Main Board Replacement
- Code: 0004
- Description: Feed Motor Overcurrent Error 1 (Big load is put on the motor instantaneously.)
- Causes: < User side > 1. Media Jam 2. Pull or Move the Carriage by hand. 3. Carriage runs into a thing/hands. 4. Media is stuck because the media end is not separated from the paper tube. 5. Heavy media is used. < Mechanical Side > 1. There is a bad contact/cut-line in the cable. 2. Screw fixing the tool carriage to wire is shifted. 3. Motor is broken./Life 4. Head/Servo Board is broken.
- Troubleshooting Guides:
- Code: 0008
- Description: Feed Motor Overcurrent Error 2 (A little load is put on the motor for a long time.)
- Causes: < User side > 1. Media Jam 2. Pull or Move the Carriage by hand. 3. Carriage runs into a thing/hands. 4. Media is stuck because the media end is not separated from the paper tube. 5. Heavy media is used. < Mechanical Side > 1. There is a bad contact/cut-line in the cable. 2. Screw fixing the tool carriage to wire is shifted. 3. Motor is broken./Life 4. Head/Servo Board is broken.
- Troubleshooting Guides:
- Code: 0010
- Description: Scan Motor Deviation Error
- Causes: < User side > 1. Media Jam 2. Pull or Move the Carriage by hand. 3. Carriage runs into a thing/hands. 4. Media is stuck because the media end is not separated from the paper tube. 5. Heavy media is used. < Mechanical Side > 1. There is a bad contact/cut-line in the cable. 2. Screw fixing the tool carriage to wire is shifted. 3. Motor is broken./Life 4. Head/Servo Board is broken.
- Troubleshooting Guides:
- Code: 0040
- Description: Scan Motor Overcurrent Error 1 (Big load is put on the motor instantaneously.)
- Causes: < User side > 1. Media Jam 2. Pull or Move the Carriage by hand. 3. Carriage runs into a thing/hands. 4. Media is stuck because the media end is not separated from the paper tube. 5. Heavy media is used. < Mechanical Side > 1. There is a bad contact/cut-line in the cable. 2. Screw fixing the tool carriage to wire is shifted. 3. Motor is broken./Life 4. Head/Servo Board is broken.
- Troubleshooting Guides:
- Code: 0080
- Description: Scan Motor Overcurrent Error 2 (A little load is put on the motor for a long time.)
- Causes: < User side > 1. Media Jam 2. Pull or Move the Carriage by hand. 3. Carriage runs into a thing/hands. 4. Media is stuck because the media end is not separated from the paper tube. 5. Heavy media is used. < Mechanical Side > 1. There is a bad contact/cut-line in the cable. 2. Screw fixing the tool carriage to wire is shifted. 3. Motor is broken./Life 4. Head/Servo Board is broken.
- Troubleshooting Guides:
- Code: 0101
- Description: Limit Position Error
Limit Initialization in the Service Mode has not been done. - Causes: Limit Initialization in Service Mode has not been done.
- Troubleshooting Guides: 1) Carry out Limit Position Initialize.
- Code: 0102
- Description: Head Lock Sensor Error
Even though the machine carries out the regular movement, the output of the Head Lock Sensor does not reach the expected value. - Causes: Head Lock Sensor does not work correctly or is broken.
- Troubleshooting Guides: 1) Head Lock Replacement 2) Check the mechanical Backlash or loose with the scanning axes.
- Code: 0103
- Description: Limit Sensor Error
Even though the machine carries out the regular movement, the output of Limit Sensor does not reach the expected value. - Causes: Limit Sensor does not work correctly or is broken.
- Troubleshooting Guides: 1) Limit Sensor Replacement 2) Check the mechanical Backlash or loose with the scanning axes.
- Code: 0104
- Description: Cap Unit Protection Error
Even though the machine carries out the regular movement, the output of Cap Sensor does not become to reach the expected value. - Causes: Disorder of Cap Motor Fault of Cap Unit Fault of Cap Sensor Cut-line or short-circuit of Cable and Flexible Cable
- Troubleshooting Guides: 1) Cap Motor Replacement 2) Cap Unit Replacement 3) Cap Sensor Replacement 4) Cable and Flexible Cable Replacement
- Code: 0105
- Description: Tool Carriage Connection Error
Machine fails to connect the Tool Carriage to the Head Carriage. - Causes: Fault of Tool Carriage Connection Loose of Connection Part Fault of the Limit Position Initialize value Limit Sensor does not work correctly or is broken.
- Troubleshooting Guides: 1) Check the mechanical Backlash or loose with the Tool Carriage part. 2) Lock Position Adjustment 3) Limit Position and Cut Down Position Initialize 4) Limit Sensor Replacement
- Code: 0106
- Description: Tool Carriage Disconnection Error
Machine fails to disconnect the Tool Carriage to the Head Carriage - Causes: Disorder of Cap Motor Loose of Connection Part Fault of the Limit Position Initialize value Limit Sensor does not work correctly or is broken.
- Troubleshooting Guides: 1) Check the mechanical Backlash or loose with the Tool Carriage part. 2) Lock Position Adjustment 3) Limit Position and Cut Down Position Initialize 4) Limit Sensor Replacement
- Code: 0107
- Description: Unset up of the Linear Encoder
Linear Encoder Setup has not been done. - Causes: Linear Encoder Setup has not been done.
- Troubleshooting Guides: 1) Carry out Linear Encoder Setup.
- Code: 0108
- Description: Wiper Unit Protection Error
Even though the machine carries out the regular movement, the output of the Wiper Height Sensor does not become to reach the expected value. - Causes: Disorder of Wiper Height Sensor Fault of Wiper Unit Fault of Wiper Height Sensor Disconnection or short-circuit of Cable and Flexible Cable
- Troubleshooting Guides: 1) Wiper Motor Replacement 2) Wiper Unit Replacement 3) Wiper Height Sensor Replacement 4) Cable and Flexible Cable Replacement
- Code: 0109
- Description: Wiper Protection Error
Even though the machine carries out the regular movement, the output of the Wiper Sensor does not reach the expected value. - Causes: Disorder of Wiper Sensor Fault of Wiper Unit Fault of Wiper Sensor Cut-line or short-circuit of Cable and Flexible Cable
- Troubleshooting Guides: 1) Wiper Motor Replacement 2) Wiper Unit Replacement 3) Wiper Sensor Replacement 4) Cable and Flexible Cable Replacement
- Code: 0110
- Description: Linear Encoder Error
Input value from Linear Encoder is not changed when Linear Encoder is set up the Origin. When Motor stops during printing, Motor does not complete the movement which is supposed to be done. - Causes: Read error of Linear Encoder Read error of Encoder on Scan Motor side Wire is not fixed to Head Carriage firmly.
- Troubleshooting Guides: 1) Confirm whether Encoder Scale is between the slit of Encoder Module in a whole width of the machine. 2) Linear Encoder Replacement 3) Scan Motor Replacement 4) Confirm Cable Connection between Linear Encoder Board and Print Carriage Board. 5) Confirm Connection between Wire and Head Carriage. 6) Main Board Replacement
- Code: 0111
- Description: Tool / Crop Mark Sensor Adjustment Error
This error occurs when the machine performs the Auto Crop Mark Detection or the Auto Print / Cut adjustment without the Tool / Crop Mark Sensor Adjustment. - Causes: Tool / Crop Mark Sensor Adjustment has not been performed.
- Troubleshooting Guides: 1 ) Tool / Crop Mark Sensor Adjustment
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer
2. Press and hold the Resume/Cancel/Stop button
3. Press and hold the ON button (do not release both buttons)
4. Release the Resume/Cancel/Stop button (do not release the ON button)
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
For more information about Canon Serice Tool V5610
Contact us to get support with Roland CS540 SolJet proII Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
