Solved Roland BN20 VersaStudio Error Codes
– Printer model: Roland BN20 VersaStudio
– Error codes on Roland BN20 VersaStudio model and its description:
– Roland BN20 VersaStudio printer Error Codes and quick guide to troubleshooting:
- Code: 0102
- Description: Capping Position Sensor is ON when it should be OFF, or vice versa.
- Causes: Capping Position Sensor does not work correctly or is broken. Carriage is not located at the correct position.
- Troubleshooting Guides: Capping Position Sensor replacement Check the mechanical backlash or loose with the scan axis related parts.
- Code: 0109
- Description: Wiper unit does not work correctly.
- Causes: Wiper Unit hits the Carriage Wiper Motor error Defect of Wiper Unit Defect of Wiper Sensor Cut-line or short-circuit of cable and Flexible cable
- Troubleshooting Guides: Move the Carriages on the bed not to hit the Wiper Unit. Wiper Motor Replacement Wiper Unit Replacement Wiper Sensor Replacement Cable and Flexible Cable Replacement
- Code: 0110
- Description: Input value from Linear Encoder is not changed by the Linear Encoder origin setup. When Motor stops during printing, expected movement is not completed on some head.
- Causes: Read error of Linear Encoder. Read error of Encoder on Scan Motor side. Belt is not fi xed to Carriage fi rmly.
- Troubleshooting Guides: Check whether Encoder Scale is between the slit of Encoder Module in a whole width of the machine. Check cable connection between Linear Encoder Board and Main Board. Check connection between Belt and Carriage. Linear Encoder replacement Scan Motor replacement Main Board replacement
- Code: 0111
- Description: This error occurs when the machine performs the Auto Crop Mark Detection
- Causes: Crop-Cut Adjustment in the Service Application or the Utility has not been performed correctly.
- Troubleshooting Guides: Carry out Crop-Cut Adjustment in Service Application or the Utility.
- Code: 0112
- Description: Communication error with Cartridge IC driver
- Causes: Cartridge IC driver is broken. Cartridge IC driver cable has short circuited or cut-line.
- Troubleshooting Guides: Ink cartridge IC sensor replacement
- Code: 0130
- Description: There is a problem with Thermistor for Heater
- Causes: Thermistor cable has short circuited or cutline. Thermistor has a problem.
- Troubleshooting Guides: Check cable connection around Thermistor. Thermistor replacement
- Code: 0240
- Description: There is a problem in the Scan/Feed Motor control.
- Causes: The control of the Scan/Feed Motor is not done correctly. There is a cut-line in the Scan/Feed Motor control part on the Main Board.
- Troubleshooting Guides: Main Board replacement
- Code: 0250
- Description: Board on Head is broken
- Causes: Board on Head is broken
- Troubleshooting Guides: Head Replacement
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer
2. Press and hold the Resume/Cancel/Stop button
3. Press and hold the ON button (do not release both buttons)
4. Release the Resume/Cancel/Stop button (do not release the ON button)
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
For more information about Canon Serice Tool V5610
Contact us to get support with Roland BN20 VersaStudio Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
