Nguyễn Đăng Nam's Blog

You are here: Home / error code / Sharp AR650 with list Error Codes and Epson Et-2550 Adjustment Program

Sharp AR650 with list Error Codes and Epson Et-2550 Adjustment Program

by

Sharp AR650 Printer with list Error Codes and Epson Et-2550 Adjustment Program

– Printer model: Sharp AR650
– Error codes on Sharp AR650 with details instruction fixing:

  • Code: C04
  • Description: Abnormal feed motor
  • Troubleshooting Guides: Is the feed motor working? (Perform the output check in the test mode: 03-125/175) NO 1. Check if the signal line connector of the feed motor is disconnected. 2. Check if the connector J327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the feed motor board and LGC board are short- or open circuited. 5. Replace the feed motor. 6. Replace the LGC board. YES Is the LED on the feed motor board lit without flashing? NO 1. Check if the connector pins are disconnected and the harnesses are open-circuited. 2. Check if the conductor patterns on the feed motor board and LGC board are short- or open-circuited. 3. Replace the feed motor. 4. Replace the LGC board. YES Replace the LGC board.
  • Code: C13
  • Description: Abnormal 1st cassette tray (Paper can be fed from cassettes other than the 1st cassette.)
  • Troubleshooting Guides: Does the tray go up? (Perform the output check in the test mode: 03-242, 243) NO 1. Check if the connector of the tray-up motor is disconnected. 2. Check if the connector J311 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Is the tray-up sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[6]/[H], /[7]/[H]) NO 1. Check if the connector of the sensor is disconnected. 2. Check if the connector J310 on the LGC board is disconnected. 3. Check if the slit reaches the sensor. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the LGC board. YES 1. Check if the conductor pattern on the LGC board is short- or open-circuited. 2. Replace the LGC board.
  • Code: C14
  • Description: Abnormal 2nd cassette tray (Paper can be fed from cassettes other than the 2nd cassette.)
  • Troubleshooting Guides: Does the tray go up? (Perform the output check in the test mode: 03-242, 243) NO 1. Check if the connector of the tray-up motor is disconnected. 2. Check if the connector J311 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Is the tray-up sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[6]/[H], /[7]/[H]) NO 1. Check if the connector of the sensor is disconnected. 2. Check if the connector J310 on the LGC board is disconnected. 3. Check if the slit reaches the sensor. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the LGC board. YES 1. Check if the conductor pattern on the LGC board is short- or open-circuited. 2. Replace the LGC board.
  • Code: C15
  • Description: Abnormal 3rd cassette tray (Paper can be fed from cassettes other than the 3rd cassette.)
  • Troubleshooting Guides: Does the tray go up? (Perform the output check in the test mode: 03-242, 243) NO 1. Check if the connector of the tray-up motor is disconnected. 2. Check if the connector J311 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Is the tray-up sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[6]/[H], /[7]/[H]) NO 1. Check if the connector of the sensor is disconnected. 2. Check if the connector J310 on the LGC board is disconnected. 3. Check if the slit reaches the sensor. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the LGC board. YES 1. Check if the conductor pattern on the LGC board is short- or open-circuited. 2. Replace the LGC board.
  • Code: C16
  • Description: Abnormal 4th cassette tray (Paper can be fed from cassettes other than the 4th cassette.)
  • Troubleshooting Guides: Does the tray go up? (Perform the output check in the test mode: 03-242, 243) NO 1. Check if the connector of the tray-up motor is disconnected. 2. Check if the connector J311 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Is the tray-up sensor working? (Perform the input check in the test mode: 03-[FAX]OFF/[6]/[H], /[7]/[H]) NO 1. Check if the connector of the sensor is disconnected. 2. Check if the connector J310 on the LGC board is disconnected. 3. Check if the slit reaches the sensor. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the LGC board. YES 1. Check if the conductor pattern on the LGC board is short- or open-circuited. 2. Replace the LGC board.
  • Code: C18
  • Description: Abnormal tandem LCF tray-up motor (Paper can be fed from cassettes other than the tandem LCF cassette.)
  • Troubleshooting Guides: Does the tray move? (Perform the output check in the test mode: 03-270) NO 1. Check if the connector of the tandem LCF tray-up motor is disconnected. 2 Check if the connector J346 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Are the LCF tray bottom sensor and LCF tray-up sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[4]/[C], /[8]/[A] NO 1. Check if the connectors of the sensors are disconnected. 2. Check if the connector J312 on the LGC board is disconnected. 3. Check if the slit reaches the sensors. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the LGC board. YES 1. Check if the driving mechanism is abnormal. 2. Check if the conductor pattern on the LGC board is short- or open-circuited. 3. Replace the LGC board.
  • Code: C1A
  • Description: Abnormal tandem LCF end fence motor (Paper can be fed from cassettes other than the tandem LCF cassette.)
  • Troubleshooting Guides: Is the LCF end fence motor working? (Perform the output check in the test mode: 03-207) NO 1. Check if the connector of the tandem LCF end fence motor is disconnected. 2. Check if the connector J346 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Are the tandem LCF end fence home/stop position sensors working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[7]/[A], /[7]/[B]) NO 1. Check if the connectors of the sensors are disconnected. 2. Check if the connector J346 on the LGC board is disconnected. 3. Check if the slit reaches the sensors. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor pattern on the LGC board is short- or open-circuited. 6. Replace the LGC board. YES 1. Check if the driving mechanism is abnormal. 2. Check if the conductor pattern on the LGC board is short- or open-circuited. 3. Replace the LGC board.
  • Code: C1C
  • Description: Abnormal external LCF tray-up motor (Paper can be fed from cassettes other than the external LCF)
  • Troubleshooting Guides: Is the tray motor driving? (Perform the output check in the test mode: 03-271) 1. Check if the connector J815 on the LCF tray motor is not disconnected. 2. Check if the connectors J801~804 on the LCF board are not disconnected. 3. Check if the connector of the tray-up sensor is not disconnected. 4. Check if the actuator reaches the sensor. 5. Check if the power (24V) is supplied to 1pin and 2pin of J803. If not, check if the door switch is turned ON and the harness of it is not open-circuited. 6. Replace the LCF board. 7. Replace the LGC board. Is the tray-up sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER] OFF/[1]/[C] 1. Check if the connector of the tray-up sensor is not disconnected. 2. Check if the connectors J801~804 on the LCF board are not disconnected. 3. Check if the actuator reaches the sensor. 4. Check if the coppector pins are not disconnected and the harness is not open-circuited. 5. Replace the LCF board. 6. Replace the LGC board. 1. Check if the tray lifting mechanism has no abnormality. 2. Replace the LCF board. 3. Replace the LGC board.
  • Code: C26
  • Description: Peak detection error
  • Troubleshooting Guides: Does the exposure lamp light? (Perform the output check in the test mode: 03-267) YES 1. Check if the connectors on the CCD and SLG boards are disconnected. 2. Check if the shading correction plate is dirty. 3. Check if the conductor pattern on the CCD board is short- or open-circuited. 4. Check if the conductor pattern on the SLG board is short- or open-circuited. 5. Replace the lens unit. 6. Replace the SLG board. NO 1. Check if the connectors of the exposure lamp and inverter are disconnected. 2. Check the SLG board if the connector pin J9 is disconnected and the harness is short- or opencircuited. 3. Check if the conductor pattern on the SLG board is short- or open-circuited. 4. Replace the SLG board. 5. Replace the inverter. 6. Replace the exposure lamp.
  • Code: C27
  • Description: Carriage home position sensor not going OFF within a fixed time
  • Troubleshooting Guides: Are the carriages slightly moved to the feeding direction?/Are the carriages staying at a position other than home position? YES Check if the circuit of the SLG board is abnormal. NO 1. Check if the connector pin is disconnected and the harness is short- or open-circuited. 2. Check if the conductor pattern on the SLG board is short- or open-circuited. 3. Replace the SLG board.
  • Code: C28
  • Description: Carriage home position sensor not going ON within a fixed time
  • Troubleshooting Guides: Do the carriages make a big noise after they arrive at the home position? YES The carriage home position sensor is not turned ON. 1. Check if the connector of the sensor is disconnected. 2. Check if the circuit of the SLG board is abnormal. NO The carriages are stopped at the home position and do not move. 1. Check if the connector pins are disconnected and the harnesses are short- or open-circuited. 2. Check if the conductor pattern on the SLG board is short- or open-circuited. 3. Replace the SLG board.
  • Code: C36
  • Description: Abnormal main charger wire cleaner drive motor
  • Troubleshooting Guides: (1) Check if the main charger is not disconnected. (2) Check if the wire cleaner drive motor is driving. (3) Replace the LGC board.
  • Code: C37
  • Description: Abnormal transfer belt cam motor
  • Troubleshooting Guides: (1) Check if the connector of the transfer belt cam motor is not disconnected. (2) Check if the transfer belt contact/release switch is working properly. (3) Replace the transfer belt cam motor. (4) Replace the LGC board.
  • Code: C41
  • Description: Abnormal thermistor or heater at the power ON
  • Troubleshooting Guides: 1. Check the thermistors (1) Check if the connectors are disconnected. (2) Check if the center and side thermistors (front, rear) are in contact with the surface of the fuser roller properly? (3) Check if the harnesses of the center and side thermistors are open-circuited. 2. Check the IH control board and IH coil (1) Check if the IH coil is broken. (2) Check if the connector of the IH coil is disconnected. (3) Check if the thermostat is blown. (4) Check if the connectors on the IH control board are disconnected (AC input connector and LGC I/F connectors J552 and J553). (5) Check if the IH control board or the switching power supply unit are abnormal. • Replace the IH control board. 3. Check the LGC board (1) Check if the connector J334 is disconnected. (2) Check if the conductor pattern on the LGC board is short- or open-circuited. (3) Replace the LGC board. 4. Clear the status counter After repairing the matter which caused the error [C41], perform the following: (1) Turn ON the power while [0] and [8] are pressed simultaneously. (2) Enter “400” with the digital keys, then press the [START] key. (3) Change the current status counter value “1” or “2” to “0”, then press the [SET] key or [INTERRUPT] key (to cancel [C41]). (4) Turn the power OFF and then back ON. Make sure that the copier enters the normal standby state.
  • Code: C43
  • Description: Abnormal thermistor after abnormality judgment
  • Troubleshooting Guides: 1,2.3. Check the thermistors, IH control board, IH coil and LGC board Check the above components following the procedure 1, 2 and 3 for [C41]. 4. Clear the status counter Change the current status counter value (08-400) “4” to “0” for [C43] and “5”, “7” or “9” to “0” for [C44], taking the same procedure as that for [C41]. * The status counter value is as follows in the following cases. Change them to ‘0’ respectively. • The error occurred during warming-up: ‘4’ or ‘5’ • The error occurred after the machine has become ready: ‘6’ • The temperature detected by the center thermistor is 230°C or higher: ‘9’ • The temperature detected by the side thermistor is 270°C or higher: ‘9’
  • Code: C44
  • Description: Abnormal fuser after abnormality judgment
  • Troubleshooting Guides: 1,2.3. Check the thermistors, IH control board, IH coil and LGC board Check the above components following the procedure 1, 2 and 3 for [C41]. 4. Clear the status counter Change the current status counter value (08-400) “4” to “0” for [C43] and “5”, “7” or “9” to “0” for [C44], taking the same procedure as that for [C41]. * The status counter value is as follows in the following cases. Change them to ‘0’ respectively. • The error occurred during warming-up: ‘4’ or ‘5’ • The error occurred after the machine has become ready: ‘6’ • The temperature detected by the center thermistor is 230°C or higher: ‘9’ • The temperature detected by the side thermistor is 270°C or higher: ‘9’counter value (08-400) “6” to “0”.
  • Code: C45
  • Description: Abnormal side thermistor after the copier has become ready
  • Troubleshooting Guides: 1. Check the side thermistor (1) Check if the connector is disconnected. (2) Check if the side thermistor is in contact with the surface of the fuser roller properly. (3) Check if the harness of the side thermistor is open-circuited. 2. Check the LGC board (1) Check if the connector J334 is disconnected. (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the LGC board. 3. Clear the status counter Change the current status counter value (08-400) “6” to “0”.
  • Code: C46
  • Description: Abnormal pressure roller thermistor during a ready state
  • Troubleshooting Guides: 1. Check the pressure roller thermistor. (1) Check if the connector is not disconnected. (2) Check if the pressure roller thirmistor closely touches the surface of the pressure roller. (3) Check if the harness of the pressure roller thermistor is not open-circuited. 2. Check the LGC board. (1) Check if the connector J334 is not disconnected. (2) Check if the conductor pattern on the LGC board is not short- or open-circuited. (3) Replace the LGC board. 3. Clear the status counter. Change the current status counter value (08-400) “3” or “8” to “0”.

Sharp AR650 error code

– Sharp AR650 printer Error Codes and quick guide on repairing:

  • Code: C47
  • Description: Abnormal IH power voltage / IH initialization error
  • Troubleshooting Guides: 1. Check the AC input voltage Check if the AC input voltage is within the specified range. (especially when the heater becomes ON after the power is turned ON (the copier is warming up)) 2. Check the thermostat Check if the thermostat is blown. 3. Check the IH control board (1) Check if the AC input connector on the IH control board, the LGC I/F connectors J522 and J553 are disconnected? (2) Check if the fuse on the IH control board has blown. (3) Replace the IH control board. 4. Check the LGC board (1) Check if the connector J334 is disconnected. (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the LGC board. 5. Clear the status counter Change the values “10”, “11”, “13”, “14” or “17” of the status counter (08-400) to “0”. * The status counter value is as follows in the following cases. Change them to ‘0’ respectively. • The error occurred immediately after the power was turned ON: ’10’ • The error occurred before the temperature of the fuser roller reaches 40°C: ’11’ • The error occurred before the temperature of the fuser roller reaches 150°C: ’14’ • The error occurred before the machine has become ready: ’13’ • The error occurred when the machine is in the ready state: ’17’
  • Code: C48
  • Description: IGBT high temperature
  • Troubleshooting Guides: 1. Check the operation of the IH fan Check if the IH fan is rotating normally. (Is the connector securely connected?) 2. Check the IH control board (1) Check if the IGBT or IGBT radiation plate are normal. (Is the radiation plate securely attached?) (2) Check if the conductor pattern on the board is short- or open-circuited. (3) Replace the IH control board. 3. Clear the status counter Change the values “12”, “14”, “15” or “18” of the status counter (08-400) to “0”. * The status counter value is as follows in the following cases. Change them to ‘0’ respectively. • The error occurred before the temperature of the fuser roller reaches 40°C: ’12’ • The error occurred before the temperature of the fuser roller reaches 150°C: ’15’ • The error occurred before the machine has become ready: ’14’ • The error occurred when the machine is in the ready state: ’18’
  • Code: C49
  • Description: Abnormal IH circuit or coil
  • Troubleshooting Guides: 1. Check the IH control board (1) Check if the conductor pattern on the board is short or open-circuited. (2) Replace the IH control board. 2. Check the IH coil (1) Check if the coil is broken or shorted. (2) Replace the IH coil. 3. Clear the status counter Change the values “13”, “15”, “16” or “19” of the status counter (08-400) to “0”. * The status counter value is as follows in the following cases. Change them to ‘0’ respectively. • The error occurred before the temperature of the fuser roller reaches 40°C: ’13’ • The error occurred before the temperature of the fuser roller reaches 150°C: ’16’ • The error occurred before the machine has become ready: ’15’ • The error occurred when the machine is in the ready state: ’19’ [C47], [C48] and [C49] can be cleared by turning OFF and ON the main switch as long as the problem was solved, and the status counter does not have to be changed to ‘0’. The value of the status counter remains until the next service call overwrites the value.
  • Code: C4A
  • Description: Cleaning web finished
  • Troubleshooting Guides: (1) Check if the cleaning web is remaining. (2) Check if the connector J332 on the LGC board is not disconnected. (3) Check if there is no abnormality at the web sensor. (4) Replace the LGC board. [CD5] Abnormality at the web motor signal path (1) Check if the connector of the web motor and connector pins are not disconnected. (2) Check if the drawer connector and connector pins are not disconnected. (3) Check if the harness between the drawer connector and the web motor is not open-circuited. (4) Check if the connector of the LGC board and connector pins are not disconnected. (5) Check if the harness between the connector of the LGC board and the drawer connector is not opencircuited. (6) Replace the LGC board. (7) Replace the fuser unit.
  • Code: C55
  • Description: RADF I/F error
  • Troubleshooting Guides: Is the harness between the ADF board and SLG board open-circuited? Replace the harness. Is the ADF board short- or open-circuited? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment. Replace the SLG board.
  • Code: C56
  • Description: Communication error between main CPU and PFC
  • Troubleshooting Guides: (1) Check if the conductor pattern around IC57 and IC58 is not short- or open-circuited. (2) Replace the LGC board.
  • Code: C57
  • Description: Communication error between main CPU and IPC board
  • Troubleshooting Guides: Is the connector between the LGC board and IPC board connected inadequately? Reconnect the connecter. Is the conductor pattern on the IPC board short- or open-circuited? Replace the IPC board. Replace the LGC board.
  • Code: C58
  • Description: Communication error between IPC board and finisher
  • Troubleshooting Guides: Is a specified finisher used? Replace to the specified finisher. Is the harness between the IPC board and finisher control board open-circuited? Replace the harness. Is the conductor pattern on the IPC board is short- or open-circuited? Replace the IPC board. Replace the finisher control board.
  • Code: C59
  • Description: Communication error between main CPU and laser CPU
  • Troubleshooting Guides: (1) Check if the harness between the LGC board and PLG board is not disconnected or open-circuited. (2) Check if the conductor pannern around IC13, IC25, IC57, J327 and J342 on the LGC board is not short- or open-circuited. (3) Check if the conductor pattern around IC4, IC19 and J202 on the PLG board is not short- or opencircuited. (4) Replace the LGC board. (5) Replace the PLG board.
  • Code: C73
  • Description: EEPROM initialization error
  • Troubleshooting Guides: (1) Check the ADF board, mainly IC13, for short- and open-circuits. (2) Replace the ADF board. (3) Perform the ‘Automatic adjusment of RADF sensor and EEPROM initialization’ and ‘Adjusment of the tray width sensor’.
  • Code: C82
  • Description: Read sensor adjustment error
  • Troubleshooting Guides: Is there any extraneous material between the read sensor and reflective mirror? Remove the extraneous material. Is the reflective mirror tainted? Clean up the mirror. Is the conductor pattern around IC6, IC11 and CN11 on the ADF board short- or open-circuited? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment. 1. Replace the read sensor. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment.
  • Code: C83
  • Description: Original length sensor adjustment error
  • Troubleshooting Guides: Is there any extraneous material between the original length sensor and reflective mirror? Remove the extraneous material. Is the reflective mirror tainted? Clean up the mirror. Is the conductor pattern around IC6, IC11 and CN15 on the ADF board short- or open-circuited? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment. 1. Replace the original length sensor. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment.
  • Code: C84
  • Description: Small original reverse sensor adjustment error
  • Troubleshooting Guides: Is there any extraneous material between the small original reverse sensor and reflective mirror? Remove the extraneous material. Is the reflective mirror tainted? Clean up the mirror. Is the conductor pattern around IC6, IC11 and CN16 on the ADF board short- or open-circuited? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment. 1. Replace the small original reverse sensor. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment.
  • Code: C85
  • Description: Abnormal tray lift motor
  • Troubleshooting Guides: Is the lifting tray lifted when originals are set on the feeding tray? Is the loading of the lifting tray normal? Adjust the mechanical loading. Remove, if any, extraneous materials. Is the power voltage for CN5-5 and CN6 on the ADF board 24V? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment. Replace the lifting tray motor. Is the upper limit sensor working properly when the lifting tray is lifted? Replace the upper limit sensor. Is the lifting tray lowered when originals are removed from the original tray? Is the loading of the lifting tray normal? Adjust the mechanical loading. Remove, if any, extraneous materials. 1. Replace the lower limit sensor. 2. Replace the ADF board. 3. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment.
  • Code: C86
  • Description: Large original exit sensor adjustment error
  • Troubleshooting Guides: Is there any extraneous material between the large original exit sensor and reflective mirror? Remove the extraneous material. Is the reflective mirror tainted? Clean up the mirror. Is the conductor pattern around IC6, IC11 and CN11 on the ADF board short- or open-circuited? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment. 1. Replace the large original exit sensor. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray width sensor adjustment
  • Code: C94
  • Description: Abnormal main CPU
  • Troubleshooting Guides: Is the “Call for Service” displayed even after the main switch is turned OFF and back ON ? NO Leave it and see what happens. YES 1. Check if the circuit pattern between the main CPU and MROM is short- or open-circuited. 2. Replace the LGC board if this error occurs frequently.
  • Code: CA1
  • Description: Abnormal polygonal motor
  • Troubleshooting Guides: Is the polygonal motor rotating? NO 1. Check if the connector J302 on the LGC board is disconnected. 2. Check if the connector J203 on the POL board is disconnected. 3. Check if the harness is open-circuited and the connector pin is disconnected. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the laser optical unit. 6. Replace the LGC board. YES Are the pins-3 and -4 of the connector J203 on the POL board always level “L”? NO 1. Check if the conductor pattern on the LGC board is short- or open-circuited. 2. Replace the laser optical unit. 3. Replace the LGC board. YES 1. Check if the conductor pattern on the LGC board is short- or open-circuited. 2. Replace the LGC board.
  • Code: CA2
  • Description: H-Sync detection error
  • Troubleshooting Guides: Are the harness connecting the connector (J308) on the LGC board and connector (J202) on the SNS board open-circuited? Are the connectors disconnected? YES Replace the harness. Connect the disconnected connectors. NO 1. Replace the LGC board. 2. Replace the laser optical unit.
  • Code: CA3
  • Description: Secondary scanning coarse adjustment error
  • Troubleshooting Guides: Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open-circuited or any connector disconnected? Replace the harness. Reconnect the connector. 1. Replace the PLG board. 2. Replace the laser optical unit.
  • Code: CA5
  • Description: Laser power adjustment error
  • Troubleshooting Guides: Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open-circuited or any connector disconnected? Replace the harness. Reconnect the connector. 1. Replace the PLG board. 2. Replace the laser optical unit.
  • Code: CA6
  • Description: Laser calibration error
  • Troubleshooting Guides: Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open-circuited or any connector disconnected? Replace the harness. Reconnect the connector. 1. Replace the PLG board. 2. Replace the laser optical unit.
  • Code: CA9
  • Description: Image data transmission error from SYS board
  • Troubleshooting Guides: Is the harness between the PLG board and SYS board open-circuited or the connector disconnected? Replace the harness. Reconnect the connector. 1. Replace the PLG board. 2. Replace the SYS board.
  • Code: CAA
  • Description: Secondary scanning fine adjustment error
  • Troubleshooting Guides: Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open-circuited or any connector disconnected? Replace the harness. Reconnect the connector. 1. Replace the PLG board. 2. Replace the laser optical unit.
  • Code: CAB
  • Description: Secondary scanning inter-page compensation error
  • Troubleshooting Guides: Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open-circuited or any connector disconnected? Replace the harness. Reconnect the connector. 1. Replace the PLG board. 2. Replace the laser optical unit.
  • Code: CAC
  • Description: Primary scanning dot adjustment error
  • Troubleshooting Guides: Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open-circuited or any connector disconnected? Replace the harness. Reconnect the connector. 1. Replace the PLG board. 2. Replace the laser optical unit.
  • Code: CB1
  • Description: Abnormal feed motor
  • Troubleshooting Guides: [Procedure 1] Is second feed motor (M8) rotating in reverse at the fixed timing? NO Replace second feed motor or finisher controller PC board. YES Is the shutter securely attached to the shutter upper/lower bars? NO Attach it securely. YES Turn the feed roller-2 in reverse by hand. Do the shutter upper/lower bars move up and down? NO Fix the mechanism including the shutter upper/lower bars and gears of the feed roller-2. YES Is the shutter closed detecting switch (MS4) working normally? NO Replace the switch. YES Replace the finisher controller PC board. [Procedure 2] Is second feed motor (M8) rotating in reverse at the fixed timing? NO Replace second feed motor or finisher controller PC board. YES Is the shutter securely attached to the shutter upper/lower bars? NO Attach it securely. YES Turn feed roller-2 in reverse by hand. Do the shutter upper/lower bars move up and down? NO Fix the mechanism including the shutter upper/lower bars and gears of the feed roller-2. YES Is the shutter open sensor (PI5) working normally? NO Replace the sensor. YES Replace the finisher controller PC board. [Procedure 3] Check the safety zone switch (MS3). Is the switch working normally? NO Replace the switch. YES Is the safety zone switch (MS3) correctly pressed? NO Fix the mechanism. YES Is the shutter closed detecting switch (MS4) working normally? NO Replace the switch. YES Is the shutter closed detecting switch (MS4) correctly pressed? NO Fix the mechanism. YES Replace the finisher controller PC board.
  • Code: CB2
  • Description: Abnormal delivery motor
  • Troubleshooting Guides: Rotate the delivery motor by hand. Does it rotate smoothly? NO Fix the mechanism. YES Is the delivery motor clock sensor (PI10) working normally? NO Replace the sensor. YES Does the voltage between J11-4 and -5 on the finisher controller PC board become 24V when the delivery motor starts rotating? NO Replace the finisher controller PC board. YES Is the wiring between the delivery motor and finisher controller PC board correct? YES Correct the wiring. NO Replace the motor.
  • Code: CB3
  • Description: Abnormal tray lift motor
  • Troubleshooting Guides: <Procedure 1> Is the tray 1 home position sensor working properly? Replace the tray 1 home position sensor. Is the tray 1 lifting mechanism working properly? Correct the defect of the mechanism. Is 24V supplied to the tray1 lifting motor from the finisher control board at the timing of tray driving? Replace the finisher control board. Is the harness between the finisher control board and tray 1 lifting motor normal? Replace the harness. Replace the tray 1 lifting motor. <Procedure 2> Is the tray 1 lifted/lowered? Are the tray 1 lifting motor clock sensor 1 and 2 working properly? Replace the sensor board. Replace the finisher control board. Is the power supplied to the motor from the finisher control board at the timing of tray 1 lifting? Replace the finisher control board. Is there any abnormality at the tray 1 lifting mechanism? Correct the defect of the mechanism. Replace the tray 1 lifting motor. <Procedure 3> Is the tray 2 home position sensor working properly? Replace the tray 2 home position sensor. Is the tray 2 lifting mechanism working properly? Correct the defect of the mechanism. Is 24V supplied to the tray 2 lifting motor from the finisher control board at the timing of tray driving? Replace the finisher control board. Is the harness between the finisher control board and tray 2 lifting motor normal? Replace the harness. Replace the tray 2 lifting motor. <Procedure 4> Is the tray 2 lifted/lowered? Are the tray 2 lifting motor clock sensor 1 and 2 working normally? Replace the sensor board. Replace the finisher control board. Is the power supplied to the motor from the finisher control board at the timing of tray 2 lifting? Replace the finisher control board. Is there any abnormality at the tray 2 lifting mechanism? Correct the defect of the mechanism. Replace the tray 2 lifting motor.
  • Code: CB4
  • Description: Abnormal alignment motor
  • Troubleshooting Guides: Is the alignment guide home position sensor (PI6) working normally? NO Replace the sensor. YES Is the wiring between the finisher controller PC board and the alignment motor (M3) correct? YES Correct the wiring. NO Is there any mechanical problem with the alignment guide movement path? YES Fix the mechanism. NO Is the problem solved by replacing the alignment motor? NO Replace the finisher controller PC board. YES END
  • Code: CB5
  • Description: Abnormal staple motor
  • Troubleshooting Guides: Is the wiring between the stapler and the finisher controller PC board correct? YES Connect or replace the harness. NO Is the problem solved by replacing the stapler? NO Replace the finisher controller PC board. YES END
  • Code: CB6
  • Description: Abnormal stapler shift motor
  • Troubleshooting Guides: Is the stapler shift home position sensor (PI7) working normally? NO Replace the sensor. YES Is the wiring between the finisher controller PC board and the stapler shift motor (M4) correct? YES Correct the wiring. NO Is there any mechanical problem with the stapler stand motion path? YES Fix the mechanism. NO Is the problem solved by replacing the stapler shift motor? NO Replace the finisher controller PC board. YES END
  • Code: CB7
  • Description: Abnormal height sensor
  • Troubleshooting Guides: [Procedure 1] Is the problem solved by turning the power of the copier OFF and ON? YES END NO Is the wiring between the finisher controller PC board and the height sensor (PS1) correct? YES Correct the wiring. NO Is the voltage between J6-2(+) and J6-4(-) on the finisher controller PC board 5V DC? NO Replace the finisher controller PC board. YES Re-adjust the height sensor. Replace the height sensor if it still causes the problem. [Procedure 2] Is the connector J6 on the finisher controller PC board, J114 of the height sensor (PS1) or relay connector J212 and J213 disconnected? YES Connect the connector(s). NO Is the voltage between J6-2(+) and J6-4(-) on the finisher controller PC board 5V DC? NO Replace the finisher controller PC board. YES Is the wiring between the finisher controller PC board and height sensor correct? YES Correct the wiring. NO Replace the height sensor. [Procedure 3] Is the problem solved by readjusting the DIP switch? YES END NO Is the wiring between the finisher controller PC board and height sensor (PS1) correct? YES Correct the wiring. NO Is the voltage between J6-2(+) and J6-4(-) on the finisher controller PC board 5V DC? NO Replace the finisher controller PC board. YES Replace the height sensor.
  • Code: CB8
  • Description: Abnormal backup RAM data
  • Troubleshooting Guides: Is the problem solved by turning the power of the copier OFF and ON? YES END NO Replace the finisher controller PC board.
  • Code: CB9
  • Description: Abnormal saddle stitcher paper pushing plate motor
  • Troubleshooting Guides: [Procedure 1] Is the paper pushing plate home position sensor (PI14S) working normally? NO Replace the sensor. YES Is the paper pushing plate motor (M8S) operating at the fixed timing? YES Replace the saddle stitcher controller PC board. NO Is the paper pushing plate drive mechanism normal? NO Fix the mechanism. YES Is the problem solved by replacing the paper pushing plate motor (M8S)? NO Replace the saddle stitcher controller PC board. YES END [Procedure 2] Is the paper pushing plate top position sensor (PI15S) working normally? NO Replace the sensor. YES Is the paper pushing plate motor (M8S) operating at the fixed timing? YES Replace the saddle stitcher controller PC board. NO Is there any problem with the paper pushing plate drive mechanism? YES Fix the mechanism. NO Is the problem solved by replacing the paper pushing plate motor (M8S)? NO Replace the saddle stitcher controller PC board. YES END [Procedure 3] Is the paper pushing plate motor clock sensor (PI1S) working normally? NO Replace the sensor. YES Is the paper pushing plate motor (M8S) operating at the fixed timing? YES Replace the saddle stitcher controller PC board. NO Is there any problem with the pushing plate drive mechanism? YES Fix the mechanism. NO Is the problem solved by replacing the paper pushing plate motor (M8S)? NO Replace the saddle stitcher controller PC board. YES END
  • Code: CBA
  • Description: Abnormal saddle stitcher stitch motor (front)
  • Troubleshooting Guides: Are the front and rear stitchers and their stands installed properly? NO Install them properly. YES Are the stitcher home position switches (MS7S/MS5S) on the front and rear stitchers working normally? NO Replace the front or rear stitcher. YES Are the front and rear stitchers operating at the fixed timing? NO Replace the front or rear stitcher. YES Check the wiring between the stitcher and saddle stitcher controller PC board. If there is no problem, replace the controller PC board.
  • Code: CBB
  • Description: Abnormal saddle stitcher stitch motor (rear)
  • Troubleshooting Guides: Are the front and rear stitchers and their stands installed properly? NO Install them properly. YES Are the stitcher home position switches (MS7S/MS5S) on the front and rear stitchers working normally? NO Replace the front or rear stitcher. YES Are the front and rear stitchers operating at the fixed timing? NO Replace the front or rear stitcher. YES Check the wiring between the stitcher and saddle stitcher controller PC board. If there is no problem, replace the controller PC board.
  • Code: CBC
  • Description: Abnormal saddle stitcher alignment motor
  • Troubleshooting Guides: Is the alignment plate home position sensor (PI5S) working normally? NO Replace the sensor. YES Is the alignment motor (M5S) operating at the fixed timing? YES Replace the saddle stitcher controller PC board. NO Is the alignment plate drive mechanism normal? NO Fix the mechanism. YES Is the problem solved by replacing the alignment motor (M5S)? NO Replace the saddle stitcher controller PC board. YES END
  • Code: CBD
  • Description: Abnormal saddle stitcher guide motor
  • Troubleshooting Guides: Is the guide home position sensor (PI13S) working normally? NO Replace the sensor. YES Is the guide motor (M3S) operating at the fixed timing? YES Replace the saddle stitcher controller PC board. NO Is the guide plate drive mechanism normal? NO Fix the mechanism. YES Is the problem solved by replacing the guide motor (M3S)? NO Replace the saddle stitcher controller PC board. YES END
  • Code: CBE
  • Description: Abnormal saddle stitcher paper folding motor
  • Troubleshooting Guides: Is the paper folding motor clock sensor (PI4S) working normally? NO Replace the sensor. YES Is the paper folding motor (M2S) operating at the fixed timing? YES Replace the saddle stitcher controller PC board. NO Is the paper folding roller drive mechanism normal? NO Fix the mechanism. YES Is the problem solved by replacing the paper folding motor (M2S)? NO Replace the saddle stitcher controller PC board. YES END
  • Code: CBF
  • Description: Abnormal saddle stitcher paper positioning plate motor
  • Troubleshooting Guides: Is the paper positioning plate home position sensor (PI7S) working normally? NO Replace the sensor. YES Is the paper positioning plate operating at the fixed timing? YES Replace the saddle stitcher controller PC board. NO Is the paper positioning plate drive mechanism normal? NO Fix the mechanism. YES Is the problem solved by replacing the paper positioning plate motor (M4S)? NO Replace the saddle stitcher controller PC board. YES END
  • Code: CC0
  • Description: Abnormal saddle stitcher sensor connector connection
  • Troubleshooting Guides: [Procedure 1] Is the guide home position sensor (PI13S) connected to the saddle stitcher controller PC board? NO Connect it to the board. YES Is the wiring between the sensor and the saddle stitcher correct? YES Correct the wiring. NO Is 1 or 2V DC being supplied from J9-7 on the saddle stitcher controller PC board? NO Replace the saddle stitcher controller PC board. YES Is J9-11 on the saddle stitcher controller PC board correctly connected to the ground? NO Replace the saddle stitcher controller PC board. YES END [Procedure 2] Is the paper pushing plate home position sensor (PI14S) connected to the saddle stitcher controller PC board? NO Connect it to the board. YES Is the wiring between the sensor and the saddle stitcher correct? YES Correct the wiring. NO Is 1 or 2V DC being supplied from J9-10 on the saddle stitcher controller PC board? NO Replace the saddle stitcher controller PC board. YES Is J9-11 on the saddle stitcher controller PC board properly connected to the ground? NO Replace the saddle stitcher controller PC board. YES END [Procedure 3] Is the paper pushing plate top position sensor (PI15S) connected to the saddle stitcher controller PC board? NO Connect it to the board. YES Is the wiring between the sensor and the saddle stitcher correct? YES Correct the wiring. NO Is 1 or 2V DC being supplied from J9-13 on the saddle stitcher controller PC board? NO Replace the saddle stitcher controller PC board. YES Is J9-14 on the saddle stitcher controller PC board properly connected to the ground? NO Replace the saddle stitcher controller PC board. YES END
  • Code: CC1
  • Description: Abnormal saddle stitcher microswitch
  • Troubleshooting Guides: [Procedure 1] Is the switch actuator for the inlet door working properly? NO Fix the mechanism. YES Is the inlet cover switch (MS1S) working normally? NO Replace the switch. YES Measure the voltage of J10-8 on the saddle stitcher controller PC board when the inlet door is open. Is it 5V? NO The inlet cover sensor (PI9S) is broken. Replace it. YES Measure the voltage between J19-2 (+) and J19-1 (-) on the saddle stitcher controller PC board. Is it 24 V? NO Replace the saddle stitcher controller PC board. YES Check the wiring between J19 on the finisher controller PC board and J1 on the saddle stitcher controller PC board. If there is no problem, replace the saddle stitcher controller PC board. [Procedure 2] Is the switch actuator for the front door working properly? NO Fix the mechanism. YES Is the front cover switch (MS2S) working normally? NO Replace the switch. YES Measure the voltage of J11-12 on the saddle switcher controller PC board when the front door is opened. Is it 5V? NO The front door opening/closing sensor is broken. Replace it. YES Replace the saddle stitcher controller PC board. [Procedure 3] Is the switch actuator for the delivery door working properly? NO Fix the mechanism. YES Is the delivery cover switch working normally? NO Replace the switch. YES Measure the voltage of J11-9 on the saddle stitcher controller PC board when the delivery door is opened. Is it 5V ? NO The delivery cover sensor (PI3S) is broken. Replace it. YES Replace the saddle stitcher controller PC board.
  • Code: CC2
  • Description: Abnormal communication between finisher and saddle stitcher
  • Troubleshooting Guides: Is the problem solved by turning OFF and ON the power switch of the copier? YES END NO Is the wiring between the finisher controller PC board and the saddle stitcher controller PC board connected? YES Connect the wiring. NO Measure the voltage between J3-2 (+) and J3-1 (-) on the finisher controller PC board. Is it DC 5V? NO Replace the finisher controller PC board. YES Replace the saddle stitcher controller PC board.
  • Code: CC4
  • Description: Abnormal swing motor
  • Troubleshooting Guides: [Procedure 1] Rotate the swing motor in reverse by hand. Does the swing guide move up and down? NO Fix the swing mechanism. YES Is the swing guide closed detection switch-2 (MS6) working normally? NO Replace the switch. YES Is the swing guide open sensor (PI18) working normally? NO Replace the sensor. YES Is the swing motor (M7) rotating in reverse at the fixed timing? NO Replace the motor. YES END [Procedure 2] Is the safety zone switch (MS3) working normally? NO Replace the switch. YES Is the safety zone switch (MS3) correctly pressed? NO Fix the mechanism. YES Is the swing guide closed detection switch-2 (MS6) working normally? NO Replace the switch. YES Is the swing guide closed detection switch-2 (MS6) correctly pressed? NO Fix the mechanism. YES Replace the finisher controller PC board. [Procedure 3] Is the swing motor clock sensor (PI20) working normally? NO Replace the sensor. YES Does the voltage between J11-6 and -7 on the finisher controller PC board become 24V when the swing motor starts rotating? NO Replace the finisher controller PC board. YES Is the wiring between the swing motor and finisher controller PC board correct? YES Correct the wiring. NO Replace the swing motor.
  • Code: CC5
  • Description: Abnormal horizontal registration motor
  • Troubleshooting Guides: Is the horizontal registration home position sensor (PI1P) working normally? NO Replace the sensor. YES Is the wiring between the horizontal registration home position sensor (PI1P) and finisher controller PC board correct? YES Correct the wiring. NO Is the horizontal registration mechanism normal? NO Fix the mechanism. YES Is the problem solved by replacing the horizontal registration motor (M2P)? YES END NO Is the problem solved by replacing the punch motor? YES END NO Is the problem solved by replacing the punch driver board? YES END NO Replace the finisher controller PC board.
  • Code: CC6
  • Description: Abnormal punch motor
  • Troubleshooting Guides: Is the punch home position sensor (PI3P) working normally? NO Replace the sensor. YES Is the wiring between the punch home position sensor (PI3P) and finisher controller PC board correct? YES Correct the wiring. NO Is the punching mechanism normal? NO Fix the mechanism. YES Is the problem solved by replacing the punch motor (M1P) ? YES END NO Is the problem solved by replacing the punch driver board? YES END NO Replace the finisher controller PC board.
  • Code: CC7
  • Description: Abnormal punch unit backup RAM data
  • Troubleshooting Guides: Is the problem solved by turing the power of the copier OFF and ON? YES END NO Replace the punch driver board.
  • Code: CCC
  • Description: Communication error between inserter and finisher
  • Troubleshooting Guides: Is the harness between the finisher control board and inserter control board normal? Replace the harness. Is 5V output to CN13-5 on the inserter control board? Replace the finisher control board. Replace the inserter control board.
  • Code: CCD
  • Description: Abnormal inserter EEPROM
  • Troubleshooting Guides: Is the conductor pattern around IC5 on the inserter control board short- or open-circuited? 1. Replace the inserter control board. 2. Perform the inserter tray volume adjustment.
  • Code: CCE
  • Description: Abnormal inserter fan
  • Troubleshooting Guides: Is the harness between the inserter control board and inserter fan normal? Replace the harness. Is the conductor pattern around Q11, Q16 and CN8 on the inserter control board short- or opencircuited? Replace the inserter fan. Replace the inserter control board.
  • Code: CD0
  • Description: Laser initializing time out
  • Troubleshooting Guides: Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open-circuited or any connector disconnected? Replace the harness. Reconnect the connector. 1. Replace the PLG board. 2. Replace the laser optical unit.
  • Code: CD1
  • Description: Abnormal drum cleaning brush motor
  • Troubleshooting Guides: (1) Check if the cleaning brush, recovery toner transport auger and recycle toner transport auger are not locked (no extraneous material or toner clod in both the toner transport sections at the cleaner unit and recycle toner unit). (2) Check if the connector on the LGC board and connector pins are not disconnected. (3) Replace the cleaning brush drive motor and recycle toner transport motor. (4) Replace the LGC board.
  • Code: CD2
  • Description: Abnormal used toner transport motor
  • Troubleshooting Guides: (1) Check if the transport auger is not locked (there is no extraneous material or toner clod). (2) Check if the connector on the LGC board and connector pins are not disconnected. (3) Replace the used toner transport motor. (4) Replace the LGC board.
  • Code: CD3
  • Description: Abnormal recycle toner transport motor
  • Troubleshooting Guides: (1) Check if the recycle toner transport auger is not locked (no extraneous material or toner clod in both the transport sections at the toner recycle unit and recycle toner hopper). (2) Check if the connector on the LGC board and connector pins are not disconnected. (3) Replace the recycle toner transport motor and toner recycle hopper motor. (4) Replace the LGC board.
  • Code: CD4
  • Description: Full toner bag
  • Troubleshooting Guides: (1) Check the toner bag. • Is the toner bag full? (2) Check the toner full detection sensor. • Is the tone full detection sensor working properly? • Is the connector not disconnected? (3) Check the used toner transport motor. • Is the used toner transport motor driving? • Does the pulley beside the motor become heavy when it is turned toward the direction of arrow (counterclockwise)? (4) Replace the LGC board. (5) Release the status counter. • Turn the power ON while pressing both the [0] and [8] keys. • Press the [START] key after inputting [399] with digital keys. • Change the status counter ‘1’, ‘2’ or ‘3’ to ‘0’ and press the [SET] or [INTERRUPT] key ([CD4] released). • Check if the copier becomes to a standby state normally when power is turned ON again. • In case that the used toner transport motor does not drive or [CD4] is not released when power is turned ON again, do the above procedure after manually turning the pulley beside the motor toward the direction of arrow (counterclockwise) several times.
  • Code: CD5
  • Description: Web motor signal path error
  • Troubleshooting Guides:
  • Code: CE0
  • Description: Abnormal comparator
  • Troubleshooting Guides: Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open-circuited or any connector disconnected? Replace the harness. Reconnect the connector. 1. Replace the PLG board. 2. Replace the laser optical unit.
  • Code: CE1
  • Description: Beam sensor detection error
  • Troubleshooting Guides: Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open-circuited or any connector disconnected? Replace the harness. Reconnect the connector. 1. Replace the PLG board. 2. Replace the laser optical unit.
  • Code: CE2
  • Description: Sensor busy error
  • Troubleshooting Guides: Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open-circuited or any connector disconnected? Replace the harness. Reconnect the connector. 1. Replace the PLG board. 2. Replace the laser optical unit.
  • Code: CE3
  • Description: Primary scanning adjustment error
  • Troubleshooting Guides: Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open-circuited or any connector disconnected? Replace the harness. Reconnect the connector. 1. Replace the PLG board. 2. Replace the laser optical unit.
  • Code: CE4
  • Description: Abnormal window comparator
  • Troubleshooting Guides: Is any harness between the PLG board and galvanic mirror, PLG board and laser drive PC board and PLG board and H-Sync detection PC board open-circuited or any connector disconnected? Replace the harness. Reconnect the connector. 1. Replace the PLG board. 2. Replace the laser optical unit.
  • Code: E01
  • Description: Leading edge of paper not reaching the fuser exit sensor
  • Troubleshooting Guides: Open the jam access cover. Is there any paper on the transport path? YES Remove the paper. NO Is the fuser exit sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]ON/[6]/[F]) NO 1. Check if the connector of the exit sensor is disconnected. 2. Check if the connector J335 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the exit sensor. 6. Replace the LGC board. YES Is the registration motor working? (Perform the output check in the test mode: 03-108/158) NO 1. Check if the connector of the registration clutch is disconnected. 2. Check if the connector J341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the registration clutch. 6. Replace the LGC board. YES Check the registration roller. Replace it if it is worn out.
  • Code: E02
  • Description: Trailing edge of paper not passing the fuser exit sensor
  • Troubleshooting Guides: Open the jam access cover. Is there any paper on the transport path? YES Remove the paper. NO Is the fuser exit sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]ON/[6]/[F]) NO 1. Check if the connector of the exit sensor is disconnected. 2. Check if the connector J335 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the exit sensor. 6. Replace the LGC board. YES Is the registration motor working? (Perform the output check in the test mode: 03-108/158) NO 1. Check if the connector of the registration clutch is disconnected. 2. Check if the connector J341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the registration clutch. 6. Replace the LGC board. YES Check the registration roller. Replace it if it is worn out.
  • Code: E03
  • Description: Paper remaining inside the copier at power ON
  • Troubleshooting Guides: Open the cover of the unit/area whose picture is flashing on the control panel. Is there any paper on the transport path? (Refer to the following table) YES Remove the paper. NO Is the sensor in the jamming area working? (Perform the input check in the test mode: refer to the following table.) NO 1. Check if the connector of the sensor is disconnected. 2. Check if any of the connectors on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the sensor. 6. Replace the LGC board. YES Replace the LGC board.
    Registration area Registration sensor 03-[ENERGY SAVER]ON/[4][E] Exit/Reverse area Exit sensor 03-[ENERGY SAVER]OFF/[6][G] Reversel sensor 1 03-[ENERGY SAVER]OFF/[6][C] Reversel sensor 2 03-[ENERGY SAVER]OFF/[6][B] Reverse transport Transport sensor 1 03-[ENERGY SAVER]OFF/[0][C] area Transport sensor 2 03-[ENERGY SAVER]OFF/[0][A] Transport sensor 3 03-[ENERGY SAVER]OFF/[0][B] Paper feeding area 1st cassette feed sensor 03-[ENERGY SAVER]OFF/[2][A] 2nd cassette feed sensor 03-[ENERGY SAVER]OFF/[3][A] 3rd cassette/Tandem LCF feed sensor 03-[ENERGY SAVER]OFF/[4][A] 4th cassette/Tandem LCF feed sensor 03-[ENERGY SAVER]OFF/[5][A] 1st cassette transport sensor 03-[ENERGY SAVER]OFF/[2][B] 2nd cassette transport sensor 03-[ENERGY SAVER]OFF/[3][B] 3rd cassette/Tandem LCF transport 03-[ENERGY SAVER]OFF/[4][B] sensor 4th cassette/Tandem LCF transport 03-[ENERGY SAVER]OFF/[5][B] sensor
  • Code: E09
  • Description: Jam caused by an abnormal HDD
  • Troubleshooting Guides: (1) Check if the connectors of the HDD are disconnected. (2) Check if the connector pins are disconnected and the harnesses are open-circuited. (3) Replace the HDD. (4) Replace the SYS board.
  • Code: E11
  • Description: Misfeeding during duplex printing (paper not reaching the registration sensor)
  • Troubleshooting Guides: Open the bypass unit cover. Is there any paper in front of the registration sensor? YES Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode:03-[ENERGY SAVER]ON/[4]/[E]) NO 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector J341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Is the reversed paper transport cluch working? (Perform the output check in the test mode: 03-220, 221) NO 1. Check if the connector of the reversed paper transport clutch is disconnected. 2. Check if the connector J334 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the reversed paper transport clutch. 6. Replace the LGC board. YES Check the rollers in the reversed papaer transport section. Replace them if they are worn out.
  • Code: E12
  • Description: Bypass misfeeding (paper not reaching the registration sensor)
  • Troubleshooting Guides: Open the bypass unit cover. Is there any paper in front of the registration sensor? YES Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]ON/[4]/[E]) NO 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector J341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Is the bypass feed clutch working? (Perform the output check in the test mode: 03-204) NO 1. Check if the connector of the bypass feed clutch is disconnected. 2. Check if the connector J327 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the bypass feed clutch. 6. Replace the LGC board. YES Check the bypass feed roller and separation roller. Replace them if they are worn out.
  • Code: E13
  • Description: 1st cassette misfeeding (paper not reaching the 1st cassette feed sensor)
  • Troubleshooting Guides: Open the feed cover. Is there any paper in front of the 1st cassette feed sensor? YES Remove the paper. NO Is the 1st cassetter feed sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[2]/[B]) NO 1. Check if the connector of the 1st cassette feed sensor is disconnected. 2. Check if the connector J329 on the LGC board is disconencted. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 1st cassette feed sensor. 6. Replace the LGC board. YES Is the 1st cassette feed clutch working? (Perform the output check in the test mode: 03-201) NO 1. Check if the connector of the 1st cassette feed clutch is disconnected. 2. Check if the connector J329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are opencircuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 1st cassette feed clutch. 6. Replace the LGC board. YES Check the 1st cassette feed roller and separation roller. Replace them if they are worn out.
  • Code: E14
  • Description: 2nd cassette misfeeding (paper not reaching the 2nd cassette feed sensor)
  • Troubleshooting Guides: Open the feed cover. Is there any paper in front of the 2nd cassette feed sensor? YES Remove the paper. NO Is the 2nd cassette feed sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[3]/[B]) NO 1. Check if the connector of the 2nd cassette feed sensor is disconnected. 2. Check if the connector J329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 2nd cassette feed sensor. 6. Replace the LGC board. YES Is the 2nd cassette feed clutch working? (Perform the output check in the test mode: 03-202) NO 1. Check if the connector of the 2nd cassette feed clutch is disconnected. 2. Check if the connector J329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are opencircuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 2nd cassette feed clutch. 6. Replace the LGC board. YES Check the 2nd cassette feed roller and separation roller. Replace them if they are worn out.
  • Code: E15
  • Description: 3rd cassette misfeeding (paper not reaching the 3rd cassette feed sensor)
  • Troubleshooting Guides: Open the feed cover. Is there any paper in front of the 3rd cassette feed sensor? YES Remove the paper. NO Is the 3rd cassette feed sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[4]/[B]) NO 1. Check if the connector of the 3rd cassette feed sensor is disconnected. 2. Check if the connector J328 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the LGC board are short- or open-circuited. 5. Replace the 3rd cassette feed sensor. 6. Replace the LGC board. YES Is the 3rd cassette/tandem LCF feed clutch working? (Perform the output check in the test mode: 03-226) NO 1. Check if the connector of the 3rd cassette/tandem LCF feed clutch is disconnected. 2. Check if the connector J328 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the LGC board are short- or open-circuited. 5. Replace the 3rd cassette/tandem LCF feed clutch. 6. Replace the LGC board. YES Check the 3rd cassette/tandem LCF feed roller and separation roller. Replace them if they are worn out.
  • Code: E16
  • Description: 4th cassette misfeeding (paper not reaching the 4th cassette feed sensor)
  • Troubleshooting Guides: Open the feed cover. Is there any paper in front of the 4th cassette feed sensor? YES Remove the paper. NO Is the 4th cassette feed sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[5]/[B]) NO 1. Check if the connector of the 4th cassette feed sensor is disconnected. 2. Check if the connector J350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the LGC board are short- or open-circuited. 5. Replace the LGC board. 6. Replace the 4th cassette feed sensor. YES Is the 4th cassette feed clutch working? (Perform the output check in the test mode: 03-228) NO 1. Check if the connector of the 4th cassette feed clutch is disconnected. 2. Check if the connector J350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the LGC board are short- or open-circuited. 5. Replace the 4th cassette feed clutch. 6. Replace the LGC board. YES Check the 4th cassette feed roller and separation roller. Replace them if they are worn out.
  • Code: E18
  • Description: Tandem LCF misfeeding (paper not reaching the tandem LCF feed sensor)
  • Troubleshooting Guides:
  • Code: E19
  • Description: External LCF misfeeding (paper not reaching the external LCF feed sensor)
  • Troubleshooting Guides: Open the LCF (release from the copier) side cover. Is there any paper in front of the LCF feed sensor? YES Remove the paper. NO Is the LCF feed sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[1]/[B]) NO 1. Check if the connector of the LCF feed sensor is disconnected. 2. Check if either of the connectors J801 to J804 on the LCF board is disconnected. 3. Check if the connector J346 on the LGC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor patterns on the LCF board and LGC board are short- or open-circuited. 6. Replace the LCF feed sensor. 7. Replace the LCF board. 8. Replace the LGC board. YES Is the LCF transport motor working? (Perform the output check in the test mode: 03-122/172) NO 1. Check if the connector of the transport motor is disconnected. 2. Check if any of the connectors J801 to 804 on the LCF board is disconnected. 3. Check if there is the abnormality of the transport driving mechanism. YES Is the LCF feed clutch working? (Perform the output check in the test mode: 03-272) NO 1. Check if the connector of the LCF feed clutch is disconnected. 2. Check if any of the connectors J801 to 804 on the LCF board is disconnected. 3. Check if the connector J346 on the LGC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor patterns on the LCF board and LGC board are short- or open-circuited. 6. Replace the LCF feed clutch. 7. Replace the LCF board. 8. Replace the LGC board. YES 1. Check if there is abnormality of the transport driving mechanism. 2. Check the LCF feed roller and separation roller. Replace them if they are worn out.
  • Code: E20
  • Description: Paper fed from the 1st cassette (not reaching the registration sensor)
  • Troubleshooting Guides: Open the jam access cover. Is there any paper in front of the registration sensor? YES Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]ON/[4]/[E]) NO 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector J341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Is the 1st cassette feed clutch working? (Perform the output check in the test mode: 03-201) NO 1. Check if the connector of the 1st cassette feed clutch is disconnected. 2. Check if the connector J329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board for short- or open-circuited. 5. Replace the upper cassette feed clutch. 6. Replace the LGC board. YES Check the 1st cassette feed roller and separation roller. Replace them if they are worn out.
  • Code: E21
  • Description: Paper fed from the 1st cassette (not reaching the 1st cassette transport sensor)
  • Troubleshooting Guides: Open the feed cover. Is there paper in front of the 1st cassette transport sensor? YES Remove the paper. NO Is the 1st cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[2]/[B]) NO 1. Check if the connector of the 1st cassette transport sensor is disconnected. 2. Check if the connector J328, 329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 1st cassette transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-202, 203, 210) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out.
  • Code: E22
  • Description: Paper fed from the 2nd cassette (not reaching the registration sensor)
  • Troubleshooting Guides: Open the bypass unit cover. Is there paper in front of the registration sensor? YES Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]ON/[4]/[E] NO 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector J341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-202, 203, 210) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out.
  • Code: E23
  • Description: Paper fed from the 2nd cassette (not reaching the 1st cassette transport sensor)
  • Troubleshooting Guides: Open the feed cover. Is there paper in front of the 1st cassette transport sensor? YES Remove the paper. NO Is the 1st cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[2]/[B]) NO 1. Check if the connector of the 1st cassette transport sensor is disconnected. 2. Check if the connector J328, 329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 1st cassette transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-202, 203, 210) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out.
  • Code: E24
  • Description: Paper fed from the 2nd cassette (not reaching the 2nd cassette transport sensor)
  • Troubleshooting Guides: Open the feed cover. Is there paper in front of the 2nd cassette transport sensor? YES Remove the paper. NO Is the 2nd cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[3]/[B]) NO 1. Check if the connector of the 2nd cassette transport sensor is disconnected. 2. Check if the connector J328,329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 2nd cassette transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-203, 210, 226) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out.
  • Code: E25
  • Description: Paper fed from the external LCF (not reaching the registration sensor)
  • Troubleshooting Guides: Is there any paper before the registration sensor when the bypass unit cover is opened? Remove the paper. Is the registration sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]ON/[4]/[E]) 1. Check if the registration connector is not disconnected. 2. Check if the connector J341 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open-circuited. 4. Check if the conductor pattern on the LGC board is not short- or opencircuited. 5. Replace the registration sensor. 6. Replace the LGC board. Is the external LCF transport motor driving? (Perform the output check in the test mode: 03-122/172) 1. Check if the connector of the transport motor is not disconnected. 2. Check if the connectors J801~804 on the LCF board are not disconnected. 3. Check if there is any abnormality at the transort drive unit. Is the external LCF feed clutch working? (Perform the output check in the test mode: 03-272) 1. Check if the external LCF clutch connector is not disconnected. 2. Check if the connectors J801~804 on the LCF board are not disconnected. 3. Check if the connector J346 on the LGC board is not disconnected. 4. Check if the connector pins are not disconnected and the harness is not open-circuited. 5. Check if the conductor pattern on the LCF and LGC boards is not short- or open-circuited. 6. Replace the external LCF feed clutch. 7. Replace the LCF board. 8. Replace the LGC board. NO YES NO YES NO YES NO YES Is the external LCF transport clutch working? (Perform the output check in the test mode: 03-273) 1. Check if the connector of the external LCF feed clutch is not disconnected. 2. Check if the connectors J801~804 on the LCF board are not disconnected. 3. Check if the connector J346 on the LGC board is not disconnected. 4. Check if the connector pins are not disconnected and the harness is not open-circuited. 5. Check if the conductor pattern on the LCF and LGC boards is not short- or open-circuited. 6. Replace the external LCF feed clutch. 7. Replace the LCF board. 8. Replace the LGC board. 1. Check if there is any abnormality at the transport drive unit. 2. Check the condition of the external LCF feed roller and separation roller and clean them, or if they are deteriorated, replace them.
  • Code: E30
  • Description: Paper fed from the 3rd cassette (not reaching the registration sensor)
  • Troubleshooting Guides: Open the bypass unit cover. Is there paper in front of the registration sensor? YES Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]ON/[4]/[E] NO 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector J341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-202, 203, 210) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out.
  • Code: E31
  • Description: Paper fed from the 3rd cassette (not reaching the 1st cassette transport sensor)
  • Troubleshooting Guides: Open the feed cover. Is there paper in front of the 1st cassette transport sensor? YES Remove the paper. NO Is the 1st cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[2]/[B]) NO 1. Check if the connector of the 1st cassette transport sensor is disconnected. 2. Check if the connector J328, 329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 1st cassette transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-202, 203, 210) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out.
  • Code: E32
  • Description: Paper fed from the 3rd cassette (not reaching the 2nd cassette transport sensor)
  • Troubleshooting Guides: Open the feed cover. Is there paper in front of the 2nd cassette transport sensor? YES Remove the paper. NO Is the 2nd cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[3]/[B]) NO 1. Check if the connector of the 2nd cassette transport sensor is disconnected. 2. Check if the connector J328,329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 2nd cassette transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-203, 210, 226) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out.
  • Code: E33
  • Description: Paper fed from the 3rd cassette (not reaching the 3rd cassette transport sensor)
  • Troubleshooting Guides: Open the feed cover. Is there any paper in front of the 3rd cassette transport sensor? YES Remove the paper. NO Is the 3rd cassette tranport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[4]/[B] NO 1. Check if the connector of the 3rd cassette transport sensor is disconnected. 2. Check if the connector J328 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the LGC board are short- or open-circuited. 5 Replace the 3rd cassette transport sensor. 6. Replace the LGC board. YES Is the transport clutch working? (Perform the output check in the test mode: 03-225) NO 1. Check if the connector of the transport clutch is disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the LGC board are short- or open-circuited. 5 Replace the transport clutch. 6 Replace the LGC board. YES Check the transport roller. Replace it if it is worn out.
  • Code: E35
  • Description: Paper fed from the 4th cassette (not reaching the 1st cassette transport sensor)
  • Troubleshooting Guides: Open the feed cover. Is there paper in front of the 1st cassette transport sensor? YES Remove the paper. NO Is the 1st cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[2]/[B]) NO 1. Check if the connector of the 1st cassette transport sensor is disconnected. 2. Check if the connector J328, 329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 1st cassette transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-202, 203, 210) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out.
  • Code: E37
  • Description: Paper fed from the 4th cassette (not reaching the 3rd cassette transport sensor)
  • Troubleshooting Guides: Open the feed cover. Is there any paper in front of the 3rd cassette transport sensor? YES Remove the paper. NO Is the 3rd cassette tranport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[4]/[B] NO 1. Check if the connector of the 3rd cassette transport sensor is disconnected. 2. Check if the connector J328 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the LGC board are short- or open-circuited. 5 Replace the 3rd cassette transport sensor. 6. Replace the LGC board. YES Is the transport clutch working? (Perform the output check in the test mode: 03-225) NO 1. Check if the connector of the transport clutch is disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the LGC board are short- or open-circuited. 5 Replace the transport clutch. 6 Replace the LGC board. YES Check the transport roller. Replace it if it is worn out.
  • Code: E38
  • Description: Paper fed from the 4th cassette (not reaching the 4th cassette transport sensor)
  • Troubleshooting Guides: Open the feed cover. Is there any paper in front of the 4th cassette transport sensor? YES Remove the paper. NO Is the 4th cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[5]/[B] NO 1. Check if the connector of the 4th cassette transport sensor is disconnected. 2. Check if the connector J350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the LGC board are short- or open-circuited. 5 Replace the 4th cassette transport sensor. 6. Replace the LGC board. YES Is the transport clutch working? (Perform the output check in the test mode: 03-225) NO 1. Check if the connector of the PFP transport clutch is disconnected. 2. Check if the connector J350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the LGC board are short- or open-circuited. 5 Replace the transport clutch. 6 Replace the LGC board. YES Check the transport roller. Replace it if it is worn out.
  • Code: E3C
  • Description: Paper fed from the tandem LCF (not reaching the registration sensor)
  • Troubleshooting Guides: Open the bypass unit cover. Is there paper in front of the registration sensor? YES Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]ON/[4]/[E] NO 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector J341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-202, 203, 210) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out.
  • Code: E3D
  • Description: Paper fed from the tandem LCF (not reaching the 1st cassette feed sensor)
  • Troubleshooting Guides: Open the feed cover. Is there paper in front of the 1st cassette transport sensor? YES Remove the paper. NO Is the 1st cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[2]/[B]) NO 1. Check if the connector of the 1st cassette transport sensor is disconnected. 2. Check if the connector J328, 329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 1st cassette transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-202, 203, 210) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out.
  • Code: E3E
  • Description: Paper fed from the tandem LCF (not reaching the 2nd cassette feed sensor)
  • Troubleshooting Guides: Open the feed cover. Is there paper in front of the 2nd cassette transport sensor? YES Remove the paper. NO Is the 2nd cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[3]/[B]) NO 1. Check if the connector of the 2nd cassette transport sensor is disconnected. 2. Check if the connector J328,329,350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 2nd cassette transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-203, 210, 226) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 329, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out.
  • Code: E3F
  • Description: Paper fed from the tandem LCF (not reaching the tandem LCF transport sensor)
  • Troubleshooting Guides: Open the feed cover. Is there paper in front of the tandem LCF transport sensor? YES Remove the paper. NO Is the tandem LCF transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[4]/[B]) NO 1. Check if the connector of the tandem LCF transport sensor is disconnected. 2. Check if the connector J328, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the tandem LCF transport sensor. 6. Replace the LGC board. YES Are the transport clutches working? (Perform the output check in the test mode: 03-225) NO 1. Check if the connectors of the transport clutches are disconnected. 2. Check if the connector J328, 350 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the transport clutches. 6. Replace the LGC board. YES Check the transport roller. Replace it if it is worn out.
  • Code: E41
  • Description: Front cover opened during printing
  • Troubleshooting Guides: Is the front cover open? YES Close the cover. NO Is the voltage of 24V being supplied from the power supply unit? (Perform the input check in the test mode: 03-[ENERGY SAVER] ON/[1]/[A]) NO 1. Check if the connector for 24V power supply is disconnected. 2. Check if the connector J344 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Replace the LGC board.
  • Code: E44
  • Description: Feed cover opened during printing
  • Troubleshooting Guides: Is the feed cover open? YES Remove the paper if there is any, then close the cover. NO Is the feed cover sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[4]/[G]) NO 1. Check if the connector of the feed cover sensor is disconnected. 2. Check if the connector J338 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are opencircuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the feed cover sensor. 6. Replace the LGC board. YES Replace the LGC board.
  • Code: E45
  • Description: LCF side cover opened during printing
  • Troubleshooting Guides: Is the LCF open? YES Remove the paper if there is any, then close the LCF. NO Is the LCF set sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[1]/[G]) NO 1. Check if the connector of the LCF set sensor is disconnected. 2. Check if either of the connectors J801 to 804 on the LCF board is disconnected. 3. Check if the connector J346 on the LGC board is disconnected. 4. Check if the connector pins are disconnected and the harnesses are open-circuited. 5. Check if the conductor patterns on the LCF board and LGC board are short- or open-circuited. 6. Replace the LCF set sensor. 7. Replace the LCF board. 8. Replace the LGC board. YES 1. Replace the LCF board. 2. Replace the LGC board.
  • Code: E46
  • Description: Bypass feed unit cover opened during printing
  • Troubleshooting Guides: Is the bypass feed unit cover open? YES Remove the paper if there is any, then close the bypass feed unit cover. NO Is the bypass feed unit cover sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[7]/[G]) NO 1. Check if the connector of the bypass feed unit cover sensor is disconnected. 2. Check if the connector J338 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor patterns on the LGC board are short- or open-circuited. 5. Replace the bypass feed unit cover sensor. 6. Replace the LGC board. YES 2. Replace the LGC board.
  • Code: E47
  • Description: Exit cover opened during printing
  • Troubleshooting Guides: Is the feeds cover close? YES Remove paper if there is any, then close the cover. NO Is the voltage of 24V being supplied from the power supply unit? (Perform the input check in the test mode: 03-[ENERGY SAVER] ON/[1]/[A]) NO 1. Check if the connector for 24V power supply is disconnected. 2. Check if the connector J344 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the LGC board. YES Is the exit cover open/close switch working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[6]/[H] NO 1. Check if the connector of the front cover opening/closing switch is disconnected. 2. Check if the connector J335 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are opencircuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the exit cover open/close switch. 6. Replace the LGC board. YES Replace the LGC board.
  • Code: E50
  • Description: Leading edge of paper not reaching the reverse sensor 2
  • Troubleshooting Guides: Is there any paper at the reverse section when the exit cover is opened? Remove the paper. Is the reverse sensor 2 working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[2]/[C]) 1. Check if the connector of the reverse sensor 2 is not disconnected. 2. Check if the connector J335 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open-circuited. 4. Check if the conductor pattern on the LGC board is not short- or opencircuited. 5. Replace the reverse sensor 2. 6. Replace the LGC board. Is the reverse motor driving? (Perform the output check in the test mode: 03-126) 1. Check if the connector of the reverse drive unit is not disconnected. 2. Check if the connector J335 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open-circuited. 4. Check if the conductor pattern on the LGC board is not short- or opencircuited. 5. Replace the LGC board. Check the myler at the reverse section and clean it, or if it is deteriorated, replace it.
  • Code: E51
  • Description: Leading edge of paper not reaching the transport sensor 1
  • Troubleshooting Guides: Is there any paper at the reverse section when the exit cover is opened? Remove the paper. Is the transport sensor 1 working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[9]/[A]) 1. Check if the connector of the transport sensor 1 is not disconnected. 2. Check if the connector J334 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open-circuited. 4. Check if the conductor pattern on the LGC board is not short- or opencircuited. 5. Replace the transport sensor 1. 6. Replace the LGC board. Is the transport roller at the horizontal transport section rotating? (Perform the output check in the test mode: 03-113/110/220) 1. Check if the drawer connector is not disconnected. 2. Check if the connectors of the transport drive clutch and transport clutch 1 are not disconnected. 3. Check if the connectors of the transport drive clutch and transport clutch 1 are not misconnected (drive clutch: black-black, transport clutch1: blue-purple). 4. Check if the connector J334 on the LGC board is not disconnected. 5. Check if the connector pins are not disconnected and the harness is not open-circuited. 6. Check if the conductor pattern on the LGC board is not short- or opencircuited. 7. Replace the transport drive clutch and transport clutch 1. 8. Replace the LGC board. 9. Check if the front side timing belt is put on properly. Check the condition of the roller at the horizontal transport section and clean it, or if it is deteriorated, replace it.
  • Code: E52
  • Description: Leading edge of paper not reaching the transport sensor 2
  • Troubleshooting Guides: Is there any paper at the reverse section when the exit cover is opened? Remove the paper. Is the transport sensor 2 working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[9]/[B]) 1. Check if the connector of the transport sensor 2 is not disconnected. 2. Check if the connector J334 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open-circuited. 4. Check if the conductor pattern on the LGC board is not short- or opencircuited. 5. Replace the transport sensor 2. 6. Replace the LGC board. Is the transport roller at the horizontal transport section rotating? (Perform the output check in the test mode: 03-113/110/220) 1. Check if the drawer connector is not disconnected. 2. Check if the connectors of the transport drive clutch and transport clutch 2 are not disconnected. 3. Check if the connectors of the transport drive clutch and transport clutch 2 are not misconnected (drive clutch: black-black, transport clutch 2: black-blue). 4. Check if the connector J334 on the LGC board is not disconnected. 5. Check if the connector pins are not disconnected and the harness is not open-circuited. 6. Check if the conductor pattern on the LGC board is not short- or opencircuited. 7. Replace the transport drive clutch and transport clutch 2. 8. Replace the LGC board. 9. Check if the front side timing belt is put on properly. Check the condition of the roller at the horizontal transport section and clean it, or if it is deteriorated, replace it.
  • Code: E54
  • Description: Leading edge of paper not reaching the transport sensor 3
  • Troubleshooting Guides: Is the transport sensor 3 working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[9]/[C]) 1. Check if the connector of the transport sensor 3 is not disconnected. 2. Check if the connector J334 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open-circuited. 4. Check is the conductor pattern on the LGC board is not short- or opencircuited. 5. Replace the transport sensor 3. 6. Replace the LGC board. Check the condition of the roller at the horizontal transport section and clean it, or if it is deteriorated, replace it.
  • Code: E55
  • Description: Paper remaining on the transport path when CRUN is OFF
  • Troubleshooting Guides: Open the cover of the unit/area whose picture is flashing on the control panel. Is there any paper on the transport path? YES Remove the paper. NO Is the sensor in the jamming area working? (Perform the input check in the test mode: refer to the following table) NO 1. Check if the connector of the sensor is disconnected. 2. Check if any of the connectors on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the sensor. 6. Replace the LGC board. YES Replace the LGC board.
    Registration area Registration sensor 03-[ENERGY SAVER]ON/[4][E] Exit/Reverse area Exit sensor 03-[ENERGY SAVER]OFF/[6][G] Reversel sensor 1 03-[ENERGY SAVER]OFF/[6][C] Reversel sensor 2 03-[ENERGY SAVER]OFF/[6][B] Reverse transport Transport sensor 1 03-[ENERGY SAVER]OFF/[0][C] area Transport sensor 2 03-[ENERGY SAVER]OFF/[0][A] Transport sensor 3 03-[ENERGY SAVER]OFF/[0][B] Paper feeding 1st cassette feed sensor 03-[ENERGY SAVER]OFF/[2][A] area 2nd cassette feed sensor 03-[ENERGY SAVER]OFF/[3][A] 3rd cassette/Tandem LCF feed sensor 03-[ENERGY SAVER]OFF/[4][A] 4th cassette/Tandem LCF feed sensor 03-[ENERGY SAVER]OFF/[5][A] 1st cassette transport sensor 03-[ENERGY SAVER]OFF/[2][B] 2nd cassette transport sensor 03-[ENERGY SAVER]OFF/[3][B] 3rd cassette/Tandem LCF transport 03-[ENERGY SAVER]OFF/[4][B] sensor 4th cassette/Tandem LCF transport 03-[ENERGY SAVER]OFF/[5][B] sensor
  • Code: E57
  • Description: Leading edge of paper not reaching the reverse sensor 1
  • Troubleshooting Guides: Is there any paper before the registration sensor when the exit cover is opened? Remove the paper. Is the reverse sensor 1 working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[2]/[B]) 1. Check if the connector of the reverse sensor 1 is not disconnected. 2. Check if the connector J335 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open-circuited. 4. Check if the conductor pattern on the LGC board is not short- or opencircuited. 5. Replace the reverse sensor 1. 6. Replace the LGC board. Is the reverse motor driving? (Perform the output check in the test mode: 03-126) 1. Check if the connector of the reverse transport unit is not disconnected. 2. Check if the connector J335 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open-circuited. 4. Check if the conductor pattern on the LGC board is not short- or opencircuited. 5. Replace the LGC board Is the gate solenoid working? (Perform the output check in the test mode: 03-274) 1. Check if the connector of the gate solenoid is not disconnected. 2. Check if the connector J335 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open-circuited. 4. Check if the conductor pattern on the LGC board is not short- or opencircuited. 5. Replace the LGC board 1. Check if there is no mechanical loading at the exit/reversal gate. 2. Check the myler at the reverse section and clean it, or if it is deteriorated, replace it.
  • Code: E58
  • Description: Trailing edge of paper not passing the reverse sensor 1 or reverse sensor 2
  • Troubleshooting Guides: Is there any paper at the reverse section when the exit cover is opened? Remove the paper. Is the reverse sensor 1/2 working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[2]/[B], [2]/[C]) 1. Check if the connector of the reverse sensor 1/2 is not disconnected. 2. Check if the connector J335 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open-circuited. 4. Check if the conductor pattern on the LGC board is not short- or opencircuited. 5. Replace the reverse sensor 1/2. 6. Replace the LGC board. 1. Check if the setting of the paper size is correct. 2. Check the condition of the roller at the reverse section and clean it, or if it is deteriorated, replace it. 3. Check if there is no mechanical loading at the follower roller and no abnormality at the myler. 4. Check if the adjustment of the reverse motor speed (05-426/427) is appropriate.
  • Code: E59
  • Description: Trailing edge of paper not passing the exit sensor
  • Troubleshooting Guides: Is the exit sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]ON/ [1]/[C]) 1. Check if the connector of the exit sensor is not disconnected. 2. Check if the connector J335 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open-circuited. 4. Check if the conductor pattern on the LGC board is not short- or opencircuited. 5. Replace the exit sensor. 6. Replace the LGC board. <Simple discharging> Is the gate solenoid working? (Perform the output check in the test mode: 03-274) 1. Check if the connector of the gate solenoid is not disconnected. 2. Check if the connector J335 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open-circuited. 4. Check if the conductor pattern on the LGC board is not short- or opencircuited. 5. Replace the LGC board. Replace the LGC board. <Reversal discharging> 1. Check if the setting of the paper size is correct. 2. Check if there is no abnormality and extraneous material at the guide and myler in front of the exit roller.
  • Code: E5A
  • Description: Leading edge of paper not reaching the exit sensor
  • Troubleshooting Guides: Is there any paper at the reverse section when the exit cover is opened? Remove the paper. Is the exit motor driving? (Perform the output check in the test mode: 03-120) 1. Check if the connector of the exit motor is not disconnected. 2. Check if the connector J336 on the LGC board is not disconnected. 3. Check if the connector pins are not disconnected and the harness is not open-circuited. 4. Check if the conductor pattern on the LGC board is not short- or opencircuited. 5. Replace the LGC board. 1. Check if the setting of the paper size is correct. 2. Check if there is no abnormality and extraneous material at the guide and myler in front of the exit roller. 3. Check if there is no mechanical loading at the exit follower roller.
  • Code: E71
  • Description: Original feeding jam
  • Troubleshooting Guides: Are the pickup roller, feed roller and separation roller dirty? YES Clean the rollers. NO Is the transport force of the rollers insufficient? YES Replace the rollers. NO Is the original abnormally curled or folded? YES Flatten and set it again.
  • Code: E72
  • Description: Original transport jam
  • Troubleshooting Guides: Are the registration roller, read roller and exit roller dirty? YES Clean the rollers.
  • Code: E73
  • Description: Original discharging jam
  • Troubleshooting Guides: Are the registration roller, read roller and exit roller dirty? YES Clean the rollers.
  • Code: E74
  • Description: Original reversing jam
  • Troubleshooting Guides: Are the read roller and reverse roller dirty? YES Clean the rollers. NO Is the reverse flapper working properly? NO Adjust the reverse solenoid.
  • Code: E76
  • Description: Small original discharging jam
  • Troubleshooting Guides: Are the registration roller, read roller, intermediate transport roller and small original reverse roller tainted? Clean up the rollers. Are the small original exit flapper and small original reverse flapper operating normally? Adjust the small original exit solenoid.
  • Code: E77
  • Description: Scanning section transport jam
  • Troubleshooting Guides: Are the registration sensor and read roller tainted? Clean up the sensor and roller.
  • Code: E7A
  • Description: RADF opened during original feeding
  • Troubleshooting Guides: Is the connector CN11 on the ADF board disconnected? Connect the connector. Is the harness between the ADF board and RADF open/close sensor open-circuited? Replace the harness. Is the RADF open/close sensor working improperly? Replace the RADF open/close sensor. Is the harness between the ADF board and APS operation sensor open-circuited? Replace the harness. Is the APS sensor working improperly? Replace the APS operation sensor. 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray volume adjustment.
  • Code: E7B
  • Description: RADF opened at the original transporting
  • Troubleshooting Guides: Is the connector CN11 on the ADF board disconnected? Connect the connector. Is the harness between the ADF board and RADF open/close sensor open-circuited? Replace the harness. Is the RADF open/close sensor working improperly? Replace the RADF open/close sensor. Is the harness between the ADF board and APS operation sensor open-circuited? Replace the harness. Is the APS sensor working improperly? Replace the APS operation sensor. 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray volume adjustment.
  • Code: E7C
  • Description: RADF opened at the large original discharging
  • Troubleshooting Guides: Is the connector CN11 on the ADF board disconnected? Connect the connector. Is the harness between the ADF board and RADF open/close sensor open-circuited? Replace the harness. Is the RADF open/close sensor working improperly? Replace the RADF open/close sensor. Is the harness between the ADF board and APS operation sensor open-circuited? Replace the harness. Is the APS sensor working improperly? Replace the APS operation sensor. 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray volume adjustment.
  • Code: E7D
  • Description: RADF opened at the small original reversing
  • Troubleshooting Guides: Is the connector CN11 on the ADF board disconnected? Connect the connector. Is the harness between the ADF board and RADF open/close sensor open-circuited? Replace the harness. Is the RADF open/close sensor working improperly? Replace the RADF open/close sensor. Is the harness between the ADF board and APS operation sensor open-circuited? Replace the harness. Is the APS sensor working improperly? Replace the APS operation sensor. 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray volume adjustment.
  • Code: E7E
  • Description: RADF opened at the small original discharging
  • Troubleshooting Guides: Is the connector CN11 on the ADF board disconnected? Connect the connector. Is the harness between the ADF board and RADF open/close sensor open-circuited? Replace the harness. Is the RADF open/close sensor working improperly? Replace the RADF open/close sensor. Is the harness between the ADF board and APS operation sensor open-circuited? Replace the harness. Is the APS sensor working improperly? Replace the APS operation sensor. 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray volume adjustment.
  • Code: E7F
  • Description: RADF opened at the original scanning section
  • Troubleshooting Guides: Is the connector CN11 on the ADF board disconnected? Connect the connector. Is the harness between the ADF board and RADF open/close sensor open-circuited? Replace the harness. Is the RADF open/close sensor working improperly? Replace the RADF open/close sensor. Is the harness between the ADF board and APS operation sensor open-circuited? Replace the harness. Is the APS sensor working improperly? Replace the APS operation sensor. 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray volume adjustment.
  • Code: E80
  • Description: Jam access cover opened at the original feeding
  • Troubleshooting Guides: Are the connector CN3 and CN12 on the ADF board disconnected? Connect the connector. Is the harness between the ADF board and cover open/close sensor open-circuited? Replace the harness. Is the cover open/close sensor working improperly? Replace the cover open/close sensor. Is the harness between the ADF board and cover open/close sensor open-circuited? Replace the harness. Is the cover open/close sensor working improperly? Replace the cover open/close sensor. Is the harness between the ADF board and RADF open/close switch open-circuited? Replace the harness. Is the RADF open/close switch working improperly? Replace the RADF open/close switch. Is 24V supplied from the copier? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray volume adjustment. Check if the power at the copier is ON.
  • Code: E81
  • Description: Jam access cover opened at the original transporting
  • Troubleshooting Guides: Are the connector CN3 and CN12 on the ADF board disconnected? Connect the connector. Is the harness between the ADF board and cover open/close sensor open-circuited? Replace the harness. Is the cover open/close sensor working improperly? Replace the cover open/close sensor. Is the harness between the ADF board and cover open/close sensor open-circuited? Replace the harness. Is the cover open/close sensor working improperly? Replace the cover open/close sensor. Is the harness between the ADF board and RADF open/close switch open-circuited? Replace the harness. Is the RADF open/close switch working improperly? Replace the RADF open/close switch. Is 24V supplied from the copier? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray volume adjustment. Check if the power at the copier is ON.
  • Code: E82
  • Description: Jam access cover opened at the large original dischaging
  • Troubleshooting Guides: Are the connector CN3 and CN12 on the ADF board disconnected? Connect the connector. Is the harness between the ADF board and cover open/close sensor open-circuited? Replace the harness. Is the cover open/close sensor working improperly? Replace the cover open/close sensor. Is the harness between the ADF board and cover open/close sensor open-circuited? Replace the harness. Is the cover open/close sensor working improperly? Replace the cover open/close sensor. Is the harness between the ADF board and RADF open/close switch open-circuited? Replace the harness. Is the RADF open/close switch working improperly? Replace the RADF open/close switch. Is 24V supplied from the copier? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray volume adjustment. Check if the power at the copier is ON.
  • Code: E83
  • Description: Jam access cover opened at the small original reversing
  • Troubleshooting Guides: Are the connector CN3 and CN12 on the ADF board disconnected? Connect the connector. Is the harness between the ADF board and cover open/close sensor open-circuited? Replace the harness. Is the cover open/close sensor working improperly? Replace the cover open/close sensor. Is the harness between the ADF board and cover open/close sensor open-circuited? Replace the harness. Is the cover open/close sensor working improperly? Replace the cover open/close sensor. Is the harness between the ADF board and RADF open/close switch open-circuited? Replace the harness. Is the RADF open/close switch working improperly? Replace the RADF open/close switch. Is 24V supplied from the copier? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray volume adjustment. Check if the power at the copier is ON.
  • Code: E84
  • Description: Jam access cover opened at the small original discharging
  • Troubleshooting Guides: Are the connector CN3 and CN12 on the ADF board disconnected? Connect the connector. Is the harness between the ADF board and cover open/close sensor open-circuited? Replace the harness. Is the cover open/close sensor working improperly? Replace the cover open/close sensor. Is the harness between the ADF board and cover open/close sensor open-circuited? Replace the harness. Is the cover open/close sensor working improperly? Replace the cover open/close sensor. Is the harness between the ADF board and RADF open/close switch open-circuited? Replace the harness. Is the RADF open/close switch working improperly? Replace the RADF open/close switch. Is 24V supplied from the copier? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray volume adjustment. Check if the power at the copier is ON.
  • Code: E85
  • Description: Jam access cover opened at the original scanning section
  • Troubleshooting Guides: Are the connector CN3 and CN12 on the ADF board disconnected? Connect the connector. Is the harness between the ADF board and cover open/close sensor open-circuited? Replace the harness. Is the cover open/close sensor working improperly? Replace the cover open/close sensor. Is the harness between the ADF board and cover open/close sensor open-circuited? Replace the harness. Is the cover open/close sensor working improperly? Replace the cover open/close sensor. Is the harness between the ADF board and RADF open/close switch open-circuited? Replace the harness. Is the RADF open/close switch working improperly? Replace the RADF open/close switch. Is 24V supplied from the copier? 1. Replace the ADF board. 2. Perform the EEPROM initialization of RADF, sensor automatical adjustment and tray volume adjustment. Check if the power at the copier is ON.
  • Code: E9F
  • Description: Punching jam
  • Troubleshooting Guides: Is there any paper remaining on the transport path in the finisher or main unit? YES Remove the paper. NO Is the connector J1 on the punch driver PC board disconnected? Is the harness connecting the punch driver PC board and punch home position sensor (PI3P) open-circuited? YES Connect the connector securely. Replace the harness. NO Is the punch home position sensor working properly? NO 1. Connect the connector of the punch home position sensor securely. 2. Replace the punch home position sensor. YES Replace the punch driver PC board.
  • Code: EA1
  • Description: Finisher paper transport delay jam
  • Troubleshooting Guides: Is there any paper remaining on the transport path in the finisher or main unit? YES Remove the paper. NO Is the connector J17 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) open-circuited? YES Connect the connector securely. Replace the harness. NO Is the inlet sensor working properly? (Check the movement of the actuator.) NO 1. Connect the connector of the inlet sensor securely. 2. Attach the actuator securely if its shaft is out of place. 3. Replace the inlet sensor. YES Replace the finisher controller PC board.
  • Code: EA2
  • Description: Finisher paper transport stop jam
  • Troubleshooting Guides: Is there any paper remaining on the transport path in the finisher or main unit? YES Remove the paper. NO Is any of the connectors J17, J24, J9 and J11 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) open-circuited? Is the harness connecting the finisher controller PC board and buffer path inlet paper sensor (PI17) open-circuited? Is the harness connecting the finisher controller PC board and buffer path paper sensor (PI14) opencircuited? Is the harness connecting the finisher controller PC board and stapling tray sensor (PI4) open-circuited? Is the harness connecting the finisher controller PC board and delivery sensor (PI3) open-circuited? YES Connect the connectors securely. Replace the harnesses. NO Is the inlet sensor working properly? (Check the movement of the actuator.) Is the buffer path inlet paper sensor working properly? (Check the movement of the actuator.) Is the buffer path paper sensor working properly? (Check the movement of the actuator.) Is the stapling tray sensor working properly? (Check the movement of the actuator.) Is the delivery sensor working properly? (Check the movement of the actuator.) NO 1. Connect the connectors of the sensors securely. 2. Attach the actuators securely if their shafts are out of place. 3. Replace the sensors. YES Replace the finisher controller PC board.
  • Code: EA3
  • Description: Paper remaining inside the finisher at power ON
  • Troubleshooting Guides: Is there any paper remaining on the transport path in the finisher? YES Remove the paper. NO Is any of the connectors J17, J24 and J11 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) open-circuited? Is the harness connecting the finisher controller PC board and buffer path inlet paper sensor (PI17) open-circuited? Is the harness connecting the finisher controller PC board and buffer path paper sensor (PI14) opencircuited? Is the harness connecting the finisher controller PC board and delivery sensor (PI3) open-circuited? YES Connect the connectors securely. Replace the harnesses. NO Is the inlet sensor working properly? (Check the movement of the actuator.) Is the buffer path inlet paper sensor working properly? (Check the movement of the actuator.) Is the buffer path paper sensor working properly? (Check the movement of the actuator.) Is the delivery sensor working properly? (Check the movement of the actuator.) NO 1. Connect the connectors of the sensors securely. 2. Attach the actuators securely if their shafts are out of place. 3. Replace the sensors. YES Replace the finisher controller PC board.
  • Code: EA4
  • Description: Finisher front door opened during printing
  • Troubleshooting Guides: Is there any paper remaining on the transport path in the finisher or main unit? YES Remove the paper. NO Is the finisher connected with the main unit? NO Connect the finisher with the main unit. YES Is the connector J12 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and joint sensor (PI15) open-circuited? YES Connect the connector securely. Replace the harness. NO Is the joint sensor working properly? NO 1. Connect the connector of the joint sensor securely. 2. Replace the joint sensor. YES Is the door of the finisher closed? NO Close the door. YES Is the connector J12 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and door opening sensor (PI16) open-circuited? YES Connect the connector securely. Replace the harness. NO Is the door opening sensor working properly? NO 1. Connect the connector of the door opening sensor securely. 2. Replace the door opening sensor. YES Is the connector J5 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and door switch (MS1) open-circuited? YES Connect the connector securely. Replace the harness. Is the door switch working properly? NO 1. Connect the connector of the door switch securely. 2. Replace the door switch. YES Is the connector J5 on the punch driver PC board disconnected? Is the harness connecting the punch driver PC board and front door switch (MS2P) open-circuited? YES Connect the connector securely. Replace the harness. NO Are the upper and front door switches working properly? NO 1. Connect the connectors of the upper and front door switches securely. 2. Replace the upper/front door switches. YES Replace the finisher controller PC board.
  • Code: EA5
  • Description: Finisher stapling jam
  • Troubleshooting Guides: Is there any paper remaining on the transport path in the finisher or main unit, or on the stapling tray? YES Remove the paper. NO Is the jam cleared by taking off the staple cartridge from the finisher and removing the staple sheet sliding it from the staple case? YES End NO Is the connector J8 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and staple home position sensor (PI22) open-circuited? YES Connect the connector securely. Replace the harness. NO Is the staple home position sensor working properly? NO 1. Connect the connector of the staple home position sensor securely. 2. Replace the staple home position sensor. YES Replace the finisher controller PC board.
  • Code: EA6
  • Description: Finisher early arrival jam
  • Troubleshooting Guides: Is there any paper remaining on the transport path in the finisher or main unit? YES Remove the paper. NO Is the connector J17 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) open-circuited? YES Connect the connector securely. Replace the harness. NO Is the inlet sensor working properly? (Check the movement of the actuator.) NO 1. Connect the connector of the inlet sensor securely. 2. Attach the actuator securely if its shaft is out of place. 3. Replace the inlet sensor. YES Replace the finisher controller PC board.
  • Code: EA8
  • Description: Saddle stitcher stapling jam
  • Troubleshooting Guides: Is there any paper remaining on the transport path in the finisher, saddle stitcher section or main unit, or on the stapling tray? YES Remove the paper. NO Is the jam cleared by taking off the staple cartridge from the finisher and removing the staples stuck in the stapling unit? YES End NO Is the connector J8 on the saddle stitcher controller PC board disconnected? Is the harness connecting the saddle stitcher controller PC board and stitcher home position switch (rear: MS5S, front: MS7S) open-circuited? YES Connect the connector securely. Replace the harness. NO Are the stitcher home position switches working properly? NO 1. Connect the connectors of the stitcher home position switches securely. 2. Replace the stitcher home position switches. YES Replace the saddle stitcher controller PC board.
  • Code: EA9
  • Description: Saddle stitcher door opened during printing
  • Troubleshooting Guides: Is there any paper remaining on the transport path in the finisher, saddle stitcher section or main unit? YES Remove the paper. NO Is the saddle stitcher door closed? NO Close the door. YES Is either of the connectors J10 or J11 on saddle stitcher controller PC board disconnected? Are the harnesses connecting the saddle stitcher controller PC board and cover opening sensors (PI2S: front door opening/closing sensor, PI3S: delivery cover sensor, PI19S: inlet cover sensor) open-circuited? YES Connect the connector securely. Replace the harness. NO Are the cover opening sensors working properly? NO 1. Connect the connectors of the cover opening sensors securely. 2. Replace the cover opening sensors. YES Replace the finisher controller PC board.
  • Code: EAA
  • Description: Paper remaining at the saddle stitcher at power ON
  • Troubleshooting Guides: Is there any paper remaining on the transport path in the finisher or saddle stitcher section? YES Remove the paper. NO Is any of the connectors J10, J13 and J9 on the saddle stitcher controller PC board disconnected? Is the harness connecting the saddle stitcher controller PC board and No.1 paper sensor (PI18S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and No.2 paper sensor (PI19S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and No.3 paper sensor (PI20S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and vertical path paper sensor (PI17S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and delivery sensor (PI11S) open-circuited? YES Connect the connectors securely. Replace the harnesses. NO Is the No.1 paper sensor working properly? (Check the movement of the actuator.) Is the No.2 paper sensor working properly? (Check the movement of the actuator.) Is the No.3 paper sensor working properly? (Check the movement of the actuator.) Is the vertical path paper sensor working properly? (Check the movement of the actuator.) Is the delivery sensor working properly? (Check the movement of the actuator.) NO 1. Connect the connectors of the sensors securely. 2. Attach the actuators securely if their shafts are out of place. 3. Replace the sensors. YES Replace the saddle stitcher controller PC board.
  • Code: EAB
  • Description: Saddle stitcher paper transport stop jam
  • Troubleshooting Guides: Is there any paper remaining on the transport path in the finisher, saddle stitcher section or main unit? YES Remove the paper. NO Is the conncetor J17 on finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) open-circuited? Is either of the connectors J10 or J9 on the saddle stitcher controller PC board disconnected? Is the harness connecting the saddle stitcher controller PC board and No.1 paper sensor (PI18S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and No.2 paper sensor (PI19S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and No.3 paper sensor (PI20S) open-circuited? Is the harness connecting the saddle stitcher controller PC board and delivery sensor (PI11S) open-circuited? YES Connect the connectors securely. Replace the harnesses. NO Is the inlet sensor working properly? (Check the movement of the actuator.) Is the No.1 paper sensor working properly? (Check the movement of the actuator.) Is the No.2 paper sensor working properly? (Check the movement of the actuator.) Is the No.3 paper sensor working properly? (Check the movement of the actuator.) Is the delivery sensor working properly? (Check the movement of the actuator.) NO 1. Connect the connectors of the sensors securely. 2. Attach the actuators securely if their shafts are out of place. 3. Replace the sensors. YES Replace the saddle stitcher controller PC board.
  • Code: EAC
  • Description: Saddle stitcher paper transport delay jam
  • Troubleshooting Guides: Is there any paper remaining on the transport path in the finisher, saddle stitcher section or main unit? YES Remove the paper. NO Is the connector J17 on the finisher controller PC board disconnected? Is the harness connecting the finisher controller PC board and inlet sensor (PI1) open-circuited? YES Connect the connector securely. Replace the harness. NO Is the inlet sensor working properly? (Check the movement of the actuator.) NO 1. Connect the connector of the sensor securely. 2. Attach the actuator securely if its shaft is out of place. 3. Replace the sensor. YES Replace the finisher controller PC board.
  • Code: EAD
  • Description: Print end command time-out jam
  • Troubleshooting Guides: Is the main motor rotating normally? NO 1. Replace the SYS board. 2. Replace the LGC board.
  • Code: EAE
  • Description: Receiving time time-out jam
  • Troubleshooting Guides: Is the finisher working? YES Replace the finisher controller PC board. NO 1. Check if the voltage (24V) is being supplied to the finisher. 2. Check the connection of the LGC board and IPC board. 3. Check if the harness connecting the IPC board and finisher I/F connector of the main unit side is open-circuited. 4. Check if the harness connecting the I/F connector of the finisher side and finisher controller PC board is open-circuited. 5. Connect the finisher controller PC board with the main unit.
  • Code: EB3
  • Description: Ready time time-out jam
  • Troubleshooting Guides: Is there paper in the main unit? NO Replace the LGC board. YES Are the IPC board and LGC board properly connected to each other? NO Connect them properly. YES Is the harness securely connected to the IPC board? NO Connect the harness securely. YES Is any of the connector pins of the harness connecting the copier and finisher disconnected or any of those harnesses open-circuited? NO Connect the pin securely/replace the harness. YES 1. Replace the IPC board. 2. Replace the LGC board. 3. Replace the finisher controller PC board.
  • Code: EB5
  • Description: Paper left on the transport path
  • Troubleshooting Guides: In case an paper is fed from the 1st cassette, bypass feed unit or reversed paper transport section: Open the bypass unit cover. Is there any paper in front of the registration sensor? YES Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]ON/[4]/[E) NO 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector J341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Check the rollers. Replace them if they are worn out. In case an paper is fed from the 2nd, 3rd, 4th or tandem LCF: Open the feed cover. Is there any paper in front of the 1st cassette transport sensor? YES Remove the paper. NO Is the 1st cassette transport sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]OFF/[2]/[B]) NO 1. Check if the connector of the 1st cassette transport sensor is disconnected. 2. Check if the connector J329 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the 1st cassette transport sensor. 6. Replace the LGC board. YES Check the rollers. Replace them if they are worn out.
  • Code: EB6
  • Description: Paper left on the transport path
  • Troubleshooting Guides: Open the bypass unit cover. Is there any paper in front of the registration sensor? YES Remove the paper. NO Is the registration sensor working? (Perform the input check in the test mode: 03-[ENERGY SAVER]ON/[4]/[E) NO 1. Check if the connector of the registration sensor is disconnected. 2. Check if the connector J341 on the LGC board is disconnected. 3. Check if the connector pins are disconnected and the harnesses are open-circuited. 4. Check if the conductor pattern on the LGC board is short- or open-circuited. 5. Replace the registration sensor. 6. Replace the LGC board. YES Check the rollers. Replace them if they are worn out.
  • Code: EC0
  • Description: Inserter feeding delay jam
  • Troubleshooting Guides: Are the pickup roller, feed roller and separation roller tainted? Clean up the rollers. Is the harness between the inserter control board and separation sensor open-circuited? Replace the harness. Is the separation sensor working improperly? Replace the separation sensor. Replace the inserter control board.
  • Code: EC1
  • Description: Inserter feeding stop jam
  • Troubleshooting Guides: Are the transport roller and reverse roller tainted? Clean up the rollers. Is the harness between the inserter control board and separation sensor open-circuited? Replace the harness. Is the separation sensor working improperly? Replace the separation sensor. Replace the inserter control board.
  • Code: EC2
  • Description: Inserter reverse path delay jam 1
  • Troubleshooting Guides: Are the transport roller and reverse roller tainted? Clean up the rollers. Is the harness between the inserter control board and reverse path sensor is open-circuited? Replace the harness. Is the reverse path sensor working improperly? Replace the reverse path sensor. Replace the inserter control board.
  • Code: EC3
  • Description: Inserter reverse path stop jam 1
  • Troubleshooting Guides: Are the transport roller and reverse roller tainted? Clean up the rollers. Is the harness between the inserter control board and reverse path sensor is open-circuited? Replace the harness. Is the reverse path sensor working improperly? Replace the reverse path sensor. Replace the inserter control board.
  • Code: EC4
  • Description: Inserter reverse path delay jam 2
  • Troubleshooting Guides: Are the transport roller and reverse roller tainted? Clean up the rollers. Is the harness between the inserter control board and reverse path sensor is open-circuited? Replace the harness. Is the reverse path sensor working improperly? Replace the reverse path sensor. Replace the inserter control board.
  • Code: EC5
  • Description: Inserter reverse path stop jam 2
  • Troubleshooting Guides: Are the transport roller and reverse roller tainted? Clean up the rollers. Is the harness between the inserter control board and reverse path sensor is open-circuited? Replace the harness. Is the reverse path sensor working improperly? Replace the reverse path sensor. Replace the inserter control board.
  • Code: EC6
  • Description: Inserter transport delay jam 1
  • Troubleshooting Guides: Is the transport roller tainted? Clean up the roller. Is the harness between the inserter control board and transport sensor is open-circuited? Replace the harness. Is the transport sensor working improperly? Replace the transport sensor. Replace the inserter control board.
  • Code: EC7
  • Description: Inserter transport stop jam 1
  • Troubleshooting Guides: Is the transport roller tainted? Clean up the roller. Is the harness between the inserter control board and transport sensor is open-circuited? Replace the harness. Is the transport sensor working improperly? Replace the transport sensor. Replace the inserter control board.
  • Code: EC8
  • Description: Inserter transport delay jam 2
  • Troubleshooting Guides: Is the transport roller tainted? Clean up the roller. Is the harness between the inserter control board and transport sensor is open-circuited? Replace the harness. Is the transport sensor working improperly? Replace the transport sensor. Replace the inserter control board.
  • Code: EC9
  • Description: Inserter transport stop jam 2
  • Troubleshooting Guides: Is the transport roller tainted? Clean up the roller. Is the harness between the inserter control board and transport sensor is open-circuited? Replace the harness. Is the transport sensor working improperly? Replace the transport sensor. Replace the inserter control board.
  • Code: ECA
  • Description: Paper remaining in the inserter when power is ON
  • Troubleshooting Guides: Is there any paper remaining at the inserter transport path? Remove the paper. Are the separation sensor, reverse path sensor and transport sensor working improperly? Replace the sensors. Replace the inserter control board.
  • Code: ECB
  • Description: Wrong size of inserter
  • Troubleshooting Guides: Is the paper size on the inserter tray consist with the size set at the copier control panel? Set the same paper size as that on the tray. Is the separation sensor working improperly? Replace the separation sensor. Perform the width adjustment of the inserter tray side guide.
  • Code: ECC
  • Description: Inserter feeding Jam
  • Troubleshooting Guides: Is the condition improved when the copier power switch is turned OFF/ON? 1. Replace the copier LGC board. 2. Replace the IPC board. 3. Replace the inserter control board.
  • Code: F07
  • Description: Communication error between SYS board and LGC board
  • Troubleshooting Guides: (1) Check if the connectors J114 and J105 on the SYS board are disconnected. (2) Check if the connector J4 on the SLG board is disconnected. (3) Check if the harness connecting the SYS and SLG boards is open-circuited and the connector pins are disconnected. (4) Check if the harness connecting the SYS board and LGC board is open-circuited and the connector pins are disconnected. (5) Check the version of the FROM on the SYS board. (6) Check the version of the MROM on the LGC board. (7) Check the version of the SROM on the SLG board. (8) Replace the SYS board. (9) Replace the SLG board. (10) Replace the LGC board.
  • Code: F10
  • Description: HDD formatting error
  • Troubleshooting Guides: (1) Initialize the HDD. (mode (08) – code ‘690’ 2) (2) Check if the HDD is mounted. (3) Check if the specified HDD is mounted. (4) Check if the connector pins of the HDD are bent. (5) Check if the power supply connector is disconnected. (6) Check if the connector J107 on the SYS board is disconnected. (7) Replace the HDD. (8) Replace the SYS board. (9) Replace the harness.
  • Code: F11
  • Description: Communication error between SYS board and SLG board
  • Troubleshooting Guides: (1) Check if the connectors J114 and J105 on the SYS board are disconnected. (2) Check if the connector J4 on the SLG board is disconnected. (3) Check if the harness connecting the SYS and SLG boards is open-circuited and the connector pins are disconnected. (4) Check if the harness connecting the SYS board and LGC board is open-circuited and the connector pins are disconnected. (5) Check the version of the FROM on the SYS board. (6) Check the version of the MROM on the LGC board. (7) Check the version of the SROM on the SLG board. (8) Replace the SYS board. (9) Replace the SLG board. (10) Replace the LGC board.





























Epson Et-2550 Adjustment Program

– OS Support: only Windows Operating System.
– Because Adjprog.exe gets Hardware ID info => Antivirus will misunderstand Adjprog.exe is the virus ==> you need to disable antivirus before extract and run Epson Et-2550 Adjustment Program or add to exclusion folder
– Limitation: Unlimited using on only 1 Computer.
– Epson Et-2550 AdjProg or Epson Et-2550 Adjustment Program or Epson Et-2550 Adj Program, is a middleware developed by third-party software to supply for Epson Et-2550 printer, making printer continuous printing without error.

Active Epson Et-2550 Adjustment Program

– Epson Et-2550 Adjustment Program is featured with clearing the waste ink counter, ultra-deep clean to clean the printhead, adjust the smoothness of the printhead, adjust the motor headers, and fix the errors: no printing, lack of colour printing, colour blur, prints with horizontal and vertical stripes…

Epson Et-2550 Adjustment Functions:

– Bi-D Adjustment
– USB ID Input
– Initial Ink Charge
– Deep Cleaning the Print Head
– Reset Waste Ink Pad Counter
– Head ID Setting
– EEPROM initial setting
– Top margin Adjustment

Using Epson Et-2550 Adjustment Program

– Choose printer model and usb connection

Using Epson Et-2550 Adjustment Program Step 1

– Choose Particular Adjustment Mode
Using Epson Et-2550 Adjustment Program Step 2

– Choose Waste Ink Pad Counter
Using Epson Et-2550 Adjustment Program Step 4

– Read Waste Ink Pad Counter
Using Epson Et-2550 Adjustment Program Step 5

– Reset Waste Ink Pad Counter
Using Epson Et-2550 Adjustment Program Step 6

Active Epson Et-2550 Adjustment Program

– Run Adjprog.exe, Copy Et-2550 Hardware ID, send it to admin email : [email protected] to get serial key and then active Epson Et-2550 Adjustment Program.

Active Epson Et-2550 Adjustment Program

Active Epson Et-2550 Adjustment Program

– More information about Epson Et-2550 Adjustment Program: https://shop.nguyendangnam.com/product/epson-et-2550-adjustment-program/
– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-tr7520-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-dfx-5000-driver-firmware-and-manuals/

Source:
https://chiplessprinter.com
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html

Contact us to get support with Sharp AR650 Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/

Bài viết liên quan

Sharp MXM1204 with list Error Codes and Epson Et-2550 Adjustment Program
Sharp MX3551 with list Error Codes and Epson Et-2550 Adjustment Program
Sharp AL1640 with list Error Codes and Epson Et-2550 Adjustment Program

Footer

Tags

Canon LBP3100 Error Canon LBP3100 repair service Canon LBP3100 troubleshooting Canon LBP6300dn Error Canon LBP6300dn repair service Canon LBP6300dn troubleshooting Canon LBP6650dn Error Canon LBP6650dn repair service Canon LBP6650dn troubleshooting Canon LBP7200Cdn Error Canon LBP7200Cdn repair service Canon LBP7200Cdn troubleshooting Canon MF4010 Error Canon Service Tool DISASSEMBLY/REASSEMBLY Epson Driver Epson ET2710 Adjustment Program Epson ET2711 Adjustment Program Epson ET4700 Adjustment Program Epson Firmware Epson L3260 Adjustment Program Epson L4250 Adjustment Program Epson L4260 Adjustment Program Epson L5290 Adjustment Program Epson L8160 Adjustment Program Epson L8180 Adjustment Program Epson L8190 Adjustment Program Epson M1100 Adjustment Program Epson M1120 Adjustment Program Epson Manual Epson XP-220 Adjustment Program Epson XP-15000/XP-15010/XP-15080 Epson XP4105 Adjustment Program fix Canon LBP3100 fix Canon LBP6300dn fix Canon LBP6650dn fix Canon LBP7200Cdn Ink Absorber MAINTENANCE printer printer cleaning printer errors Reset Epson reset ink absorber TROUBLESHOOTING

Shopping Cart

Items in Your Cart

Your cart is empty

Product

Epson Wic Key
Epson Wic Key
Fix Epson red lights blinking with errors: Service Required, A printer's ink pad at the end of its service life Please contact Epson Support. Guaranty 100% money back if it does not work (counter still 100%) !!!
Quantity:  
Price: $7.86Price: $9.99