Repair Canon NP8530 Printer Error Codes Canon Servie Tool
– Printer model: Canon NP8530
– Error codes on Canon NP8530 model and its description:
– Canon NP8530 printer Error Codes and quick guide to troubleshooting:
- Code: E000
- Description: The surface temperature of the fixing assembly upper roller fails to rise by a specified value within 90 sec after power-on. The surface temperature of the fixing assembly upper roller fails to reach 150 C within 8 min after power -on. The surface temperature of the fixing assembly upper roller fails to reach 180 C within 5 min after it has reached 150 C. The surface temperature of the fixing assembly upper roller falls below 50 C in standby.
- Code: E001
- Description: The surface temperature of the fixing assembly upper roller exceeds 250 C.
- Code: E005
- Description: The cleaning belt inside the fixing assembly has been taken up more than a specified length.
- Code: E010
- Description: After generation of the main motor drive signal, two or more pulses are not received within 2 sec.
- Code: E020
- Description: The accumulative time during which the toner supply signal (TSP) has been generated by the developing assembly reaches 3 min.
- Code: E050
- Description: The holding tray home position signal (THP) is not generated within 4 sec while the holding tray motor drive signal (TMDP1,2) is being generated. The holding tray home position signal (THP) is generated 1 sec or more while the holding tray motor drive signal (TMDP1.2) is being generated.
- Code: E13
- Description: The error detection circuit on the waste toner feed motor driver PCB has detected on overcurrent.
- Code: E203
- Description: Input of two or more clock pulses is not received within 2 sec from the scanner motor drive signal is generated.
- Code: E210
- Description: The lens home position signal (LHP) is not generated within 4.8 sec after the power switch or door switch has gone ON. The lens home position signal (LHP) is generate 2 sec or more.
- Code: E240
- Description: An error has occurred in the microprocessor on the DC controller PCB.
- Code: E243
- Description: An error has occurred in the communication between the microprocessor of the DC controller PCB and the microprocessor in the control panel.
- Code: E710
- Description: An error has occurred in the communication between the DC controller PCB and the controller PCB of the option, and the DC controller has detected the error.
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-ip2000-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-wp-4520-driver-firmware-and-manuals/
Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html
Contact us to get support with Canon NP8530 Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
