Repair Canon NP8070 Printer Error Codes Canon Servie Tool
– Printer model: Canon NP8070
– Error codes on Canon NP8070 model and its description:
– Canon NP8070 printer Error Codes and quick guide to troubleshooting:
- Code: E000
- Description: Fuser problem. Temperature too low. Heat lamp, thermal fuse or thermoswitch, thermistor, triac etc
- Code: E000
- Description: Low fuser temperature
- Code: E001
- Description: Fuser problem. Temperature too high. Probably triac
- Code: E001
- Description: High fuser temperature
- Code: E005
- Description: Fuser web finished
- Code: E005
- Description: Fuser cleaner belt user up
- Code: E010
- Description: Drive
- Code: E010
- Description: Main drive problem
- Code: E011
- Description: Drive problem. Could be main motor, scan motor, cleaning web motor or duplex motor
- Code: E011
- Description: Main motor, scan motor, cleaner belt motor, duplex motor, toner motor, lens motor or driver bd. for any of these
- Code: E020
- Description: Toner sensor problem or lack of toner feed. This occurs if toner feed signal is present for 3 min
- Code: E020
- Description: Toner empty sensor sees no toner added for 3 min probably toner feed problem
- Code: E050
- Description: Duplex problem
- Code: E050
- Description: Duplex problem
- Code: E203
- Description: Scan motor problem
- Code: E203
- Description: Scan motor
- Code: E210
- Description: Lens motor problem
- Code: E210
- Description: Lens home sensor or lens won’t leave home
- Code: E240
- Description: DC controller board
- Code: E240, E241, E242
- Description: Control board (main board)
- Code: E241
- Description: DC controller board
- Code: E242
- Description: DC controller board
- Code: E243
- Description: Operation panel board
- Code: E243
- Description: Operation panel
- Code: E400
- Description: DC controller, ADF board or 24V
- Code: E400
- Description: DC controller or document feed board
- Code: E500
- Description: DC controller or sorter board
- Code: E500
- Description: DC controller, sorter board or 24V
- Code: E510
- Description: Finisher; feed motor, pulse sensor, finisher board
- Code: E510
- Description: Finisher
- Code: E520
- Description: Finisher; stack motor, stack tray sensor, finisher board
- Code: E520
- Description: Finisher
- Code: E530
- Description: Finisher
- Code: E530
- Description: Finisher; guide plate motor, stapler guide, finisher board
- Code: E531
- Description: Finisher
- Code: E531
- Description: Finisher; staple motor, staple sensor, finisher board.
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-ip1800-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-wf-r8590-driver-firmware-and-manuals/
Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html
Contact us to get support with Canon NP8070 Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
