Repair Canon LBP6654dn Printer Error Codes Canon Servie Tool
– Printer model: Canon LBP6654dn
– Error codes on Canon LBP6654dn model and its description:
– Canon LBP6654dn printer Error Codes and quick guide to troubleshooting:
- Code: E000 0000
- Description: Temperature rise error
- Solutions: 1) Reconnect the connector on the Engine Controller PCB. 2) Turn OFF the power supply switch, and remove the Fixing Assembly. Measure the resistance value between the connector (FSRTH) at the Fixing Assembly side and grounding. If the resistance value is not between 368k ohm and 512k ohm (normal temperature), replace the Fixing Assembly. 3) If the connector at the Fixing Assembly side does not have induction while the assembly is removed, replace the assembly 4) Replace the Engine Controller PCB.
- Code: E001 0000
- Description: High temperature error 1
- Solutions: 1) Reconnect the connector on the Engine Controller PCB. 2) Turn OFF the power supply switch, and remove the Fixing Assembly. Measure the resistance value between the connector (FSRTH) at the Fixing Assembly side and grounding. If the resistance value is 1k ohm or lower, replace the Fixing Assembly. 3) Replace the Engine Controller PCB.
- Code: E003 0000
- Description: Low temperature error 1
- Solutions: 1) Reconnect the connector on the Engine Controller PCB. 2) Turn OFF the power supply switch, and remove the Fixing Assembly. Measure the resistance value between the connector (FSRTH) at the Fixing Assembly side and grounding. If the resistance value is not between 368k ohm and 512k ohm (normal temperature), replace the Fixing Assembly. 3) If there is no induction between the connector (ACN) at the Fixing Assembly side and the connector (ACH) while the assembly is removed, replace the assembly 4) Replace the Engine Controller PCB.
- Code: E004 0000
- Description: Drive circuit unit error
- Solutions: 1) Reconnect the connector on the Engine Controller PCB. 2) Check the source of power supply for the printer. When using the power supply from the power generator and the like, improve the source of power supply. Note: If the frequency of power supply is not the specified range (40Hz to 70Hz), the fixing temperature control is not executed normally, so this might cause the damage. 3) Replace the Engine Controller PCB.
- Code: E014 0000
- Description: Main Motor malfunction
- Solutions: 1) Reconnect the connector on the Main Motor. 2) Replace the Main Motor.
- Code: E06F 0068
- Description: EEPROM access failure
- Solutions: 1) Replace the EEPROM.
- Code: E100 0000
- Description: Optical Unit malfunction
- Solutions: 1) Reconnect the connector on the Laser Scanner Unit. 2) Replace the Laser Scanner Unit.
- Code: E602 0002
- Description: Bootable load failure A Bootable CD was not contained. A Bootable CD was damaged
- Solutions: 1) Burn the Bootable CD again.
- Code: E604 0000
- Description: Lack of memory capacity
- Solutions: 1) Check the memory capacity inserted to each slot.
- Code: E730 100A
- Description: Printer service call
- Solutions: Printer service call
- Code: E733
- Description: Engine communication error
- Solutions: 1) Turn OFF and then ON the power. 2) Replace the Engine Controller PCB.
- Code: E744 1000
- Description: Mismatch of the series or model of the firmware sent at the time of downloading.
- Solutions: 1) Check the supported series or model of the firmware, and burn the correct series or model of firmware.
- Code: E760 0000
- Description: CPU exception occurred
- Solutions: 1) Turn on the power again.
- Code: E805 0000
- Description: Fan malfunction
- Solutions: 1) Reconnect the connector on the Relay PCB. 2) Replace the Main Fan.
- Code: E808 0001
- Description: Low voltage malfunction
- Solutions: 1) Reconnect the connector on the Engine Controller PCB. 2) Replace the Engine Controller PCB.
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-ts8322-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-c823141-driver-firmware-and-manuals/
Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html
Contact us to get support with Canon LBP6654dn Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
