Brother MFC9550 fix error codes list
– Compatible Printer model: Brother MFC9550
– Brother MFC9550 Error Codes with instructions guide:
- Code: 71
- Description: Laser scanner motor does not lock.
- Code: 72
- Description: Cannot detect Beam Detect signal.
- Code: 73
- Description: No toner cartridge loaded.
- Code: 74
- Description: Toner empty.
- Code: 75
- Description: In-house temperature error.
- Code: 76
- Description: Fixing heater harness disconnected or broken.
- Code: 77
- Description: Heater thermister short circuit.
- Code: 78
- Description: Heater thermister harness disconnected or broken.
- Code: 79
- Description: Toner thermister disconnected or broken.
- Code: 80
- Description: Paper size setting error.
- Code: 82
- Description: Paper feeding error.
- Code: 83
- Description: Paper jam. The registration sensor remains ON.
- Code: 84
- Description: Paper jam. The paper ejection sensor remains ON.
- Code: 88
- Description: Paper jam. Even after the registration sensor has gone OFF, the paper ejection sensor still stays OFF.
- Code: 8B
- Description: Overheating error (Thermistor heat error)
- Code: A1
- Description: Top cover opened.
- Code: A2
- Description: Document too long to scan.
- Code: A3
- Description: Document not detected by the document rear sensor.
- Code: A4
- Description: 50% or more faulty of white level data.
- Code: A5
- Description: Faulty operation of DMA0 during scanning
- Code: A6
- Description: Faulty operation of DMA1 during scanning
- Code: A7
- Description: One-line feeding time-out error.
- Code: A8
- Description: One-line scanning time-out error.
- Code: A9
- Description: Abnormal scanning reference voltage.
- Code: AB
- Description: Document feed-in amount measuring error
- Code: AC
- Description: Less than 50% faulty of white level data.
- Code: B1
- Description: CODEC LSI error
- Code: B9
- Description: Light emission intensity error of the LED array.
- Code: BA
- Description: Scanning error: The left-hand black reference line which is marked on the document pressure bar for scanning width setting is not detected.
- Code: BB
- Description: Scanning error: The right-hand black reference line which is marked on the document pressure bar for scanning width setting is not detected.
- Code: BC
- Description: Scanning error: Reduction miss
- Code: BD
- Description: Scanning error: Enlargement miss
- Code: D1
- Description: The MODEM setup bit sticks to High.
- Code: D2
- Description: CTS stays OFF or ON if the MODEM RTS is turned ON or OFF, respectively.
- Code: D3
- Description: Bit B1A of the MODEM stays OFF.
- Code: D4
- Description: Bit RX of the MODEM stays OFF.
- Code: D5
- Description: The MODEM fails to complete the command transmission sequence.
- Code: D6
- Description: No MODEM interrupt for 60 seconds
- Code: E1
- Description: Microprocessor (MPU) error on the control panel PCB
- Code: E4
- Description: Out of recording paper.
- Code: E5
- Description: Recording paper set error
- Code: E6
- Description: Write error in EEPROM.
- Code: E8
- Description: Data scanning error during transmission.
- Code: EA
- Description: Document removed at phase B.
- Code: F3
- Description: Voice message recording or playing-back not started.
- Code: F4
- Description: Peripheral CNG detection adjustment error
- Code: F5
- Description: EOL not found in page memory transmission mode.
- Code: F6
- Description: PC interface error.
Solved Brother MFC9550 Error codes
- Code: FF
- Description: Interface error of page memory command
– Get more error code list with quick guide to fix printer product, click here
– About get help with reseting Epson inkpad or others, click here
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer
2. Press and hold the Resume/Cancel/Stop button
3. Press and hold the ON button (do not release both buttons)
4. Release the Resume/Cancel/Stop button (do not release the ON button)
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
For more information about Canon Serice Tool V5610
– Get more information about Epson XP 15000 troubleshooting, click here
– Buy cheap key of Epson WIC Reset Tool, CLICK HERE
– Key Epson Adjustment Program, CLICK HERE
https://dnasofts.com/download-epson-xp-6100-driver-firmware-and-manuals/
Contact us to get support with Brother MFC9550 Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
Or click here to get more ways.
Source:
https://dnasofts.com
https://shop.nguyendangnam.com/
