Brother HL5595DNH fix error codes list

Brother HL5595DNH fix error codes list

– Compatible Printer model: Brother HL5595DNH
– Brother HL5595DNH Error Codes with instructions guide:

• Code: 0102
• Description: Communication error between the engine ASIC and motor driver or faulty motor driver.
• Remedy: 1 Connection failure of the paper feed motor harness Reconnect the paper feed motor harness. 2 Paper feed motor failure Replace the paper feed motor. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 0201
• Description: Cannot detect the synchronized signal of the paper feed motor. The speed of the paper feed motor does not stabilize within the specified time.
• Remedy: 1 Connection failure of the paper feed motor harness Reconnect the paper feed motor harness. 2 Damaged fuser gear Replace the fuser gear. 3 Paper feed motor failure Replace the paper feed motor. 4 Damaged fuser unit Replace the fuser unit. 5 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 6 Damaged part in drive sub ASSY Replace the main frame L ASSY. 7 Main PCB failure Replace the main PCB ASSY.

• Code: 0203
• Description: Eject motor failure was detected.
• Remedy: 1 Connection failure of the eject motor harness Reconnect the eject motor harness. 2 Eject motor failure Replace the eject motor. 3 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 4 Damaged part in eject gears Replace the main frame L ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 0300
• Description: Cannot detect the lock signal of the polygon motor for the laser unit (second time).
• Remedy: 1 Connection failure of the laser unit flat cable Reconnect the laser unit flat cable. 2 Laser unit flat cable failure Replace the laser unit flat cable. 3 Laser unit failure Replace the laser unit. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 0305
• Description: Cannot detect the lock signal of the polygon motor for the laser unit (first time).
• Remedy: 1 Connection failure of the laser unit flat cable Reconnect the laser unit flat cable. 2 Laser unit flat cable failure Replace the laser unit flat cable. 3 Laser unit failure Replace the laser unit. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 0401
• Description: Cannot detect the synchronized signal of the polygon motor for the laser unit (second time).
• Remedy: 1 Connection failure of the laser unit flat cable Reconnect the laser unit flat cable. 2 Laser unit flat cable failure Replace the laser unit flat cable. 3 Laser unit failure Replace the laser unit. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 0405
• Description: Cannot detect the synchronized signal of the polygon motor for the laser unit (first time).
• Remedy: 1 Connection failure of the laser unit flat cable Reconnect the laser unit flat cable. 2 Laser unit flat cable failure Replace the laser unit flat cable. 3 Laser unit failure Replace the laser unit. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 0501
• Description: The center thermistor of the fuser unit has not reached the specified temperature within the specified time.
• Remedy: • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset.
  1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the center or side thermistor harness of the fuser unit. 2 Connection failure of the fuser unit heater harness Reconnect the fuser unit heater harness. 3 Connection failure of the eject sensor harness Reconnect the eject sensor harness. 4 Connection failure of the lowvoltage power supply harness Reconnect the low-voltage power supply harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 8 Main PCB failure Replace the main PCB ASSY.

• Code: 0502
• Description: The center thermistor of the fuser unit has not reached the specified temperature within the specified time after it was heated normally to the certain level.
• Remedy: • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset.
  1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the center or side thermistor harness of the fuser unit. 2 Connection failure of the fuser unit heater harness Reconnect the fuser unit heater harness. 3 Connection failure of the eject sensor harness Reconnect the eject sensor harness. 4 Connection failure of the lowvoltage power supply harness Reconnect the low-voltage power supply harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 8 Main PCB failure Replace the main PCB ASSY.

• Code: 0503
• Description: The center thermistor of the fuser unit detected a temperature higher than the specified value.
• Remedy: • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset.
  1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the center or side thermistor harness of the fuser unit. 2 Connection failure of the fuser unit heater harness Reconnect the fuser unit heater harness. 3 Connection failure of the eject sensor harness Reconnect the eject sensor harness. 4 Connection failure of the lowvoltage power supply harness Reconnect the low-voltage power supply harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 8 Main PCB failure Replace the main PCB ASSY.

• Code: 0504
• Description: After the heat unit was heated normally, the center thermistor of the fuser unit detected a temperature lower than the specified value.
• Remedy: • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset.
  1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the center or side thermistor harness of the fuser unit. 2 Connection failure of the fuser unit heater harness Reconnect the fuser unit heater harness. 3 Connection failure of the eject sensor harness Reconnect the eject sensor harness. 4 Connection failure of the lowvoltage power supply harness Reconnect the low-voltage power supply harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 8 Main PCB failure Replace the main PCB ASSY.

• Code: 0505
• Description: The center thermistor of the fuser unit detected a temperature rise greater than the specified value within the specified time.
• Remedy: • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset.
  1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the center or side thermistor harness of the fuser unit. 2 Connection failure of the fuser unit heater harness Reconnect the fuser unit heater harness. 3 Connection failure of the eject sensor harness Reconnect the eject sensor harness. 4 Connection failure of the lowvoltage power supply harness Reconnect the low-voltage power supply harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 8 Main PCB failure Replace the main PCB ASSY.

• Code: 0506
• Description: The center thermistor of the fuser unit detected a temperature fall greater than the specified value within the specified time.
• Remedy: • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset.
  1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the center or side thermistor harness of the fuser unit. 2 Connection failure of the fuser unit heater harness Reconnect the fuser unit heater harness. 3 Connection failure of the eject sensor harness Reconnect the eject sensor harness. 4 Connection failure of the lowvoltage power supply harness Reconnect the low-voltage power supply harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 8 Main PCB failure Replace the main PCB ASSY.

• Code: 0508
• Description: The side thermistor of the fuser unit did not detect a temperature rise when the heater was ON.
• Remedy: • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset.
  1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the center or side thermistor harness of the fuser unit. 2 Connection failure of the fuser unit heater harness Reconnect the fuser unit heater harness. 3 Connection failure of the eject sensor harness Reconnect the eject sensor harness. 4 Connection failure of the lowvoltage power supply harness Reconnect the low-voltage power supply harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 8 Main PCB failure Replace the main PCB ASSY.

• Code: 050A
• Description: The hardware detected a temperature error through the center thermistor or the side thermistor of the fuser unit.
• Remedy: • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset.
  1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the center or side thermistor harness of the fuser unit. 2 Connection failure of the fuser unit heater harness Reconnect the fuser unit heater harness. 3 Connection failure of the eject sensor harness Reconnect the eject sensor harness. 4 Connection failure of the lowvoltage power supply harness Reconnect the low-voltage power supply harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 8 Main PCB failure Replace the main PCB ASSY.

• Code: 050B
• Description: When the center thermistor of the fuser unit was lower than the idle temperature, the side thermistor detected a temperature higher than the specified temperature.
• Remedy: • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset.
  1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the center or side thermistor harness of the fuser unit. 2 Connection failure of the fuser unit heater harness Reconnect the fuser unit heater harness. 3 Connection failure of the eject sensor harness Reconnect the eject sensor harness. 4 Connection failure of the lowvoltage power supply harness Reconnect the low-voltage power supply harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 8 Main PCB failure Replace the main PCB ASSY.

• Code: 050C
• Description: When the center thermistor of the fuser unit was higher than the idle temperature, the side thermistor detected a temperature lower than the specified temperature.
• Remedy: • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset.
  1 Connection failure of the center or side thermistor harness of the fuser unit Reconnect the center or side thermistor harness of the fuser unit. 2 Connection failure of the fuser unit heater harness Reconnect the fuser unit heater harness. 3 Connection failure of the eject sensor harness Reconnect the eject sensor harness. 4 Connection failure of the lowvoltage power supply harness Reconnect the low-voltage power supply harness. 5 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 6 Fuser unit failure Replace the fuser unit. 7 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 8 Main PCB failure Replace the main PCB ASSY.

• Code: 0800
• Description: An error occurred in the internal temperature sensor.
• Remedy: 1 Connection failure of the internal temperature sensor harness Reconnect the internal temperature sensor harness. 2 Internal temperature sensor failure Replace the main frame L ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 0900
• Description: Detected irregular power supply for more than 100 times.
• Remedy: • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset.
  1 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. Reset counters for consumable parts (function code: 88) to reset the irregular power supply detection counter after the replacement. 2 Main PCB failure Replace the main PCB ASSY.
  Note: • The irregular power supply detection error of the low-voltage power supply PCB (error code: 0900) occurs when there is a large distortion in the power supply voltage supplied to the machine. In this case, if the same power supply is used, the same error may occur even when the low-voltage power supply PCB ASSY is replaced. Ask the user to review the installation environment. • Do not reset the power supply PCB counter before replacing it with a new one. It may cause fire.

• Code: 0A02
• Description: Detected a main fan failure.
• Remedy: 1 Connection failure of the main fan harness Reconnect the main fan harness. 2 Connection failure of the toner amount detection sensor PCB harness (light emission) Reconnect the toner amount detection sensor PCB harness (light emission). 3 Main fan failure Replace the main fan. 4 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 5 Toner amount detection sensor PCB (light emission) failure Replace the toner amount detection sensor PCB ASSY (light emission). 6 Main PCB failure Replace the main PCB ASSY.

• Code: 0B01
• Description: An error occurred in the high-voltage power supply PCB ASSY while operating.
• Remedy: • Replace the drum unit. (corona wire breakage)
  1 Connection failure of the HVPS flat cable Reconnect the HVPS flat cable. 2 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 0B02
• Description: An error occurred in the high-voltage power supply PCB ASSY when the machine was in the ready state.
• Remedy: • Replace the drum unit. (corona wire breakage)
  1 Connection failure of the HVPS flat cable Reconnect the HVPS flat cable. 2 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 1701
• Description: Detected a TT fan failure.
• Remedy: 1 Malfunction of the TT control PCB Install the latest main firmware. 2 Connection failure of the TT fan harness Reconnect the TT fan harness. 3 LT/TT connector failure (machine side or TT side) Replace the LT/TT connector of the machine side or TT side. 4 TT fan failure Replace the TT fan. 5 TT control PCB failure Replace the TT control PCB. 6 Main PCB failure Replace the main PCB ASSY.

• Code: 1801
• Description: A communication error occurred between the ASIC and T2LT control PCB in the engine. (LT only)
• Remedy: 1 Malfunction of the LT control PCB Install the latest main firmware. 2 An LT/TT connector failure (machine side or LT side) Replace the appropriate LT/TT connector of the machine side or LT side. 3 An LT control PCB failure Replace the appropriate LT control PCB. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 1802
• Description: A communication error occurred between the ASIC and T3LT control PCB ASSY in the engine. (LT only)
• Remedy: 1 Malfunction of the LT control PCB Install the latest main firmware. 2 An LT/TT connector failure (machine side or LT side) Replace the appropriate LT/TT connector of the machine side or LT side. 3 An LT control PCB failure Replace the appropriate LT control PCB. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 1803
• Description: A communication error occurred between the ASIC and T4LT control PCB ASSY in the engine. (LT only)
• Remedy: 1 Malfunction of the LT control PCB Install the latest main firmware. 2 An LT/TT connector failure (machine side or LT side) Replace the appropriate LT/TT connector of the machine side or LT side. 3 An LT control PCB failure Replace the appropriate LT control PCB. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 1808
• Description: A communication error occurred between the ASIC and TT control PCB in the engine.
• Remedy: 1 Malfunction of the TT control PCB Install the latest main firmware. 2 LT/TT connector failure (machine or TT side) Replace the LT/TT connector on the machine side or TT side. 3 TT control PCB failure Replace the TT control PCB. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 1901
• Description: Detected a TT motor failure.
• Remedy: 1 Malfunction of the TT control PCB Install the latest main firmware. 2 Connection failure of the TT motor harness Reconnect the TT motor harness. 3 LT/TT connector failure (machine side or TT side) Replace the LT/TT connector of the machine side or TT side. 4 TT motor failure Replace the TT motor. 5 TT control PCB failure Replace the TT control PCB. 6 Main PCB failure Replace the main PCB ASSY.

• Code: 1A01
• Description: A communication error occurred between the ASIC and MX control PCB in the engine.
• Remedy: 1 Connection failure of the MX control PCB harness Reconnect the MX control PCB harness. 2 MX connector failure (machine side or MX side) Replace the MX connector of the machine side or MX side. 3 MX control PCB failure Replace the MX control PCB. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 1B01
• Description: Detected an MX motor failure.
• Remedy: 1 Connection failure of the MX motor harness Reconnect the MX motor harness. 2 MX connector failure (machine side or MX side) Replace the MX connector of the machine side or MX side. 3 MX motor failure Replace the MX motor. 4 MX control PCB failure Replace the MX control PCB. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 1F00
• Description: When the TT was connected, TT balance sensor L/R wasn’t connected properly.
• Remedy: 1 Connection failure of the TT balance sensor L/R harness. Reconnect the TT balance sensor L/R harness or relay connector harness. 2 TT balance sensor L/R attachment failure Reattach the TT balance sensor L/R. 3 LT/TT connector failure (machine side or TT side) Replace the LT/TT connector of the machine side or TT side. 4 TT balance sensor L/R failure Replace the TT balance sensor L/R. 5 TT control PCB failure Replace the TT control PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY.

• Code: 3801
• Description: A temperature error occurred in the external temperature/humidity sensor.
• Remedy: 1 Connection failure of the external temperature/humidity sensor harness Reconnect the external temperature/humidity sensor harness. 2 External temperature/humidity sensor failure Replace the main frame L ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 4000
• Description: The number of rotations of the drum unit is reaching the upper limit.
• Remedy: 1 Replace the drum unit with a new one and reset the drum counter. If the error display is not cleared, the main PCB is faulty. Replace the main PCB ASSY.

• Code: 4200
• Description: The number of rotations of the drum unit has reached the upper limit. (Printing does not stop.)
• Remedy: 1 Replace the drum unit with a new one and reset the drum counter. If the error display is not cleared, the main PCB is faulty. Replace the main PCB ASSY.

• Code: 4500
• Description: The number of printable pages of the fuser unit has reached the upper limit.
• Remedy: 1 End of life of the fuser unit Replace the fuser unit. Reset counters for consumable parts (function code: 88) to reset the fuser unit counter after the replacement. 2 Replace the fuser unit with a new one and reset the fuser unit counter. If the error display is not cleared, the main PCB is faulty. Replace the main PCB ASSY.

• Code: 4600
• Description: The number of printable pages of the laser unit has reached the upper limit.
• Remedy: 1 End of life of the laser unit Replace the laser unit. Reset counters for consumable parts (function code: 88) to reset the laser unit counter after the replacement. 2 Replace the laser unit with a new one and reset the laser unit counter. If the error display is not cleared, the main PCB is faulty. Replace the main PCB ASSY.

• Code: 4B01
• Description: Dot counter or develop roller counter of the toner is reaching the upper limit.
• Remedy: 1 Replace the toner cartridge with a new one. If the error display is not cleared, the main PCB is faulty. Replace the main PCB ASSY.

• Code: 4C01
• Description: Dot counter or develop roller counter of the toner has reached the upper limit.
• Remedy: 1 Replace the toner cartridge with a new one. If the error display is not cleared, the main PCB is faulty. Replace the main PCB ASSY.

• Code: 4F01
• Description: The new toner sensor could not detect the new toner cartridge correctly.
• Remedy: • If the machine is on the uneven surface, place it on a level surface.
  1 Connection failure of the relay front harness Reconnect the relay front harness. 2 New toner actuator coming off or caught in some sections of the machine Reattach the new toner actuator. 3 Develop joint coming off or caught in some sections of the machine Reattach the develop joint. 4 New toner sensor failure Replace the relay front PCB ASSY. 5 Paper feed drive gears failure Replace the main frame L ASSY. 6 If the error display is not cleared after replacing the toner cartridge with a new one again, the main PCB is faulty. Replace the main PCB ASSY.

• Code: 5001
• Description: Printable pages set for PF kit MP have reached the upper limit.
• Remedy: 1 End of life of the applicable PF kit Replace the applicable PF kit. Reset counters for consumable parts (function code: 88) to reset the applicable PF kit counter after the replacement. 2 If the error display is not cleared after the applicable PF kit counter has been reset, the main PCB is faulty. Replace the main PCB ASSY.

• Code: 5002
• Description: Printable pages set for PF kit 1 have reached the upper limit.
• Remedy: 1 End of life of the applicable PF kit Replace the applicable PF kit. Reset counters for consumable parts (function code: 88) to reset the applicable PF kit counter after the replacement. 2 If the error display is not cleared after the applicable PF kit counter has been reset, the main PCB is faulty. Replace the main PCB ASSY.

• Code: 5003
• Description: Printable pages set for PF kit 2 have reached the upper limit.
• Remedy: 1 End of life of the applicable PF kit Replace the applicable PF kit. Reset counters for consumable parts (function code: 88) to reset the applicable PF kit counter after the replacement. 2 If the error display is not cleared after the applicable PF kit counter has been reset, the main PCB is faulty. Replace the main PCB ASSY.

• Code: 5004
• Description: Printable pages set for PF kit 3 have reached the upper limit.
• Remedy: 1 End of life of the applicable PF kit Replace the applicable PF kit. Reset counters for consumable parts (function code: 88) to reset the applicable PF kit counter after the replacement. 2 If the error display is not cleared after the applicable PF kit counter has been reset, the main PCB is faulty. Replace the main PCB ASSY.

• Code: 5005
• Description: Printable pages set for PF kit 4 have reached the upper limit.
• Remedy: 1 End of life of the applicable PF kit Replace the applicable PF kit. Reset counters for consumable parts (function code: 88) to reset the applicable PF kit counter after the replacement. 2 If the error display is not cleared after the applicable PF kit counter has been reset, the main PCB is faulty. Replace the main PCB ASSY.

• Code: 5006
• Description: Printable pages set for PF kit 5 have reached the upper limit.
• Remedy: 1 End of life of the applicable PF kit Replace the applicable PF kit. Reset counters for consumable parts (function code: 88) to reset the applicable PF kit counter after the replacement. 2 If the error display is not cleared after the applicable PF kit counter has been reset, the main PCB is faulty. Replace the main PCB ASSY.

• Code: 6001
• Description: The front cover sensor detected that the front cover was open.
• Remedy: • Close the front cover.
  1 Connection failure of the front cover sensor harness Reconnect the front cover sensor harness. 2 Connection failure of the relay front harness Reconnect the relay front harness. 3 Front cover sensor attachment failure Reattach the front cover sensor. 4 Front cover failure Replace the front cover. 5 Front cover sensor failure Replace the relay front PCB ASSY. 6 Relay front PCB failure Replace the relay front PCB ASSY. 7 Main PCB failure Replace the main PCB ASSY.

• Code: 6004
• Description: The eject sensor detected that the fuser cover was open.
• Remedy: • Close the fuser cover.
  1 Eject actuator coming off or caught in some sections of the machine Reattach the eject actuator. 2 Fuser cover attachment failure Reattach the fuser cover. 3 Connection failure of the eject sensor harness Reconnect the eject sensor harness. 4 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 6101
• Description: The toner amount detection sensor detected that the toner cartridge was not set.
• Remedy: • Set the toner cartridge correctly.
  1 Toner amount detection sensor PCB (light reception) failure Replace the toner amount detection sensor PCB ASSY (light reception). 2 Relay front PCB failure Replace the relay front PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

Solved Brother HL5595DNH Error codes

• Code: 6200
• Description: Detected that the drum unit was not set by detecting the GRID terminal current.
• Remedy: • Set the drum unit correctly.
  1 Dirt on the GRID terminals of the drum unit and those of the machine Clean the CHG and GRID terminals of the drum unit and those of the machine. 2 Dirt on the high-voltage power supply PCB terminal Clean the high-voltage power supply PCB terminal. 3 high-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 6801
• Description: The side thermistor of the fuser unit or internal temperature sensor detected a temperature higher than the specified value.
• Remedy: • Lower the room temperature. • Keep the machine away from heating appliances.
  1 Connection failure of the internal temperature sensor harness Reconnect the internal temperature sensor harness. 2 Internal temperature sensor failure Replace the main frame L ASSY. 3 Fuser unit side thermistor failure Replace the fuser unit. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 6901
• Description: An error occurred in the fuser unit when the power switch was turned ON or sleep mode was released.
• Remedy: 1 Connection failure of a fuser unit harness Reconnect the fuser unit harness. 2 Connection failure of the eject sensor harness Reconnect the eject sensor harness. 3 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 4 Fuser unit failure Replace the fuser unit. 5 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY.
  Note: • Turn OFF the power switch. After the fuser unit has cooled sufficiently, turn ON the power switch again and leave the machine for 15 minutes. This problem may then be cleared. • To release the fuser unit error after taking appropriate measures, enter the maintenance mode once and quit it with the function code 99.

• Code: 6902
• Description: Rechecking the error after the power switch was turned OFF and then ON again because an error was detected in the fuser unit. (This message is displayed for approximately 15 minutes when the machine is restarted after error code 6901 has occurred.)
• Remedy: 1 Connection failure of a fuser unit harness Reconnect the fuser unit harness. 2 Connection failure of the eject sensor harness Reconnect the eject sensor harness. 3 Eject sensor PCB failure Replace the eject sensor PCB ASSY. 4 Fuser unit failure Replace the fuser unit. 5 Low-voltage power supply PCB failure Replace the low-voltage power supply PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY.
  Note: • Turn OFF the power switch. After the fuser unit has cooled sufficiently, turn ON the power switch again and leave the machine for 15 minutes. This problem may then be cleared. • To release the fuser unit error after taking appropriate measures, enter the maintenance mode once and quit it with the function code 99.

• Code: 6A00
• Description: Detected discharge that may be attributable to dirty corona wire on the drum unit.
• Remedy: • Slide the green tab of the drum unit to left and right for two to three times to clean the corona wire. • Clean the electrode of the drum unit. • Replace the drum unit.
  1 Dirt on the high-voltage power supply PCB terminal Clean the electrodes of the machine. 2 High-voltage power supply PCB attachment failure Check if each electrode comes back smoothly after pressing it. If not, reattach each electrode. 3 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 6D00
• Description: Detected more LTs than connectible limit.
• Remedy: • Reduce LTs to acceptable numbers. • Reconnect LTs.
  1 Dust around the LT/TT connector Clean the LT/TT connector. 2 Malfunction of the LT control PCB Install the latest main firmware. 3 Machine or LT/TT connector failure Replace the machine or LT/TT connector. 4 LT control PCB failure Replace a LT control PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 6F00
• Description: Detected irregular power supply for less than 100 times.
• Remedy: • Turn the power switch OFF and then back ON again. • Use a noise filter on the power supply. • Install a voltage stabilizer to the power supply unit.

• Code: 7000
• Description: The eject sensor does not detect paper pass after the registration rear sensor detected the paper pass.
• Remedy: • Remove the jammed paper. • Replace the drum unit with a new one.
  1 Foreign object inside the machine Remove the foreign object. 2 Connection failure of the eject sensor harness Reconnect the eject sensor harness. 3 Eject actuator coming off or caught in some sections of the machine Reattach the eject actuator. 4 Fuser cover attachment failure Reattach the fuser cover. 5 Eject sensor failure Replace the eject sensor PCB ASSY. 6 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 7 Fuser unit failure Replace the fuser unit. 8 Damaged fuser gears or drum gears Replace the main frame L ASSY. 9 Main PCB failure Replace the main PCB ASSY.

• Code: 7100
• Description: The eject sensor remains ON (paper pass detected) even after the registration rear sensor detected the end of paper pass.
• Remedy: • Remove the jammed paper. • Check if the back cover is open during duplex printing.
  1 Foreign object in the rear of the machine Remove the foreign object. 2 Eject actuator caught in some sections of the machine Reattach the eject actuator. 3 Fuser cover attachment failure Reattach the fuser cover. 4 Eject sensor failure Replace the eject sensor PCB ASSY. 5 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 6 Fuser cover failure Replace the fuser cover. 7 Damaged eject roller 1 drive gears Replace the main frame L ASSY. 8 Main PCB failure Replace the main PCB ASSY.

• Code: 7200
• Description: When feeding from the MP tray, the registration rear sensor does not detect paper pass within the specified time after the registration front sensor detected paper pass.
• Remedy: • Remove the jammed paper. • Add the paper properly using the MP tray paper guide. • Close the front cover correctly.
  1 Foreign object in the front of the machine Remove the foreign object. 2 Registration rear actuator coming off or caught in some sections of the machine Reattach the registration rear actuator. 3 Connection failure of the registration front/rear sensor harness Reconnect the registration front/rear sensor harness. 4 Connection failure of the registration clutch harness Reconnect the registration clutch harness. 5 MP feed frame attachment failure Reattach the MP feed frame. 6 Registration rear sensor failure Replace the registration front/rear sensor PCB ASSY. 7 Registration clutch failure Replace the registration clutch. 8 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 9 Damaged gears in the paper feeding system Replace the main frame L ASSY. 10 Main PCB failure Replace the main PCB ASSY.

• Code: 7301
• Description: When printing from the paper tray 1, the T1 paper feed sensor does not detect paper pass within the specified time while the T1 paper empty sensor detects some paper set.
• Remedy: • Remove the jammed paper. • Add the paper properly using the paper tray 1 paper guide.
  1 Foreign object in the front of the machine Remove the foreign object. 2 T1 paper pick up roller holder attachment failure Reattach the T1 paper pick up roller holder. 3 T1 paper feed actuator attachment failure Reattach the T1 paper feed actuator. 4 Connection failure of the T1 pickup clutch harness Reattach the T1 pickup clutch harness. 5 Connection failure of the T1 paper feed sensor harness Reconnect the T1 paper feed sensor harness. 6 Connection failure of the HVPS flat cable Reconnect the HVPS flat cable. 7 PF kit 1 failure Replace the PF kit 1. 8 T1 pickup clutch failure Replace the T1 pickup clutch. 9 T1 paper feed sensor PCB failure Replace the T1 paper feed sensor PCB ASSY. 10 T1 paper empty sensor PCB failure Replace the T1 paper empty sensor PCB ASSY. 11 Damaged gears in the paper feeding system Replace the main frame L ASSY. 12 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 13 Main PCB failure Replace the main PCB ASSY.

• Code: 7302
• Description: When printing from the paper tray 1, the registration front sensor does not detect paper pass within the specified time after the T1 paper feed sensor detected paper pass.
• Remedy: • Remove the jammed paper. • Add the paper properly using the paper tray 1 paper guide.
  1 Foreign object in the front of the machine Remove the foreign object. 2 Registration front actuator attachment failure Reattach the registration front actuator. 3 Connection failure of the registration front/rear sensor harness Reconnect the registration front/rear sensor harness. 4 Registration front/rear sensor PCB failure Replace the registration front/rear sensor PCB ASSY. 5 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 6 Damaged gears in the paper feeding system Replace the main frame L ASSY. 7 Main PCB failure Replace the main PCB ASSY.

• Code: 7401
• Description: When printing from the paper tray 2, the T2(LT or TT) paper feed sensor does not detect paper pass within the specified time while the T2(LT or TT) paper empty sensor detects some paper set.
• Remedy: • Remove the jammed paper. • Add the paper properly using the paper tray 2 paper guide.
  1 Foreign object in the front of the machine Remove the foreign object. 2 Malfunction of the LT control PCB or TT control PCB Install the latest main firmware. 3 T2(LT or TT) paper pick up roller holder attachment failure Reattach the T2(LT or TT) paper pick up roller holder. 4 T2(LT or TT) paper feed actuator attachment failure Reattach the T2(LT or TT) paper feed actuator. 5 Connection failure of the T2(LT or TT) pickup clutch harness Reconnect the T2(LT or TT) pickup clutch harness. 6 Connection failure of the T2(LT or TT) paper feed sensor harness Reconnect the T2(LT or TT) paper feed sensor harness. 7 PF kit 2 failure Replace the PF kit 2. 8 T2(LT or TT) pickup clutch failure Replace the T2(LT or TT) pickup clutch. 9 T2(LT or TT) paper feed sensor PCB failure Replace the T2(LT or TT) paper feed sensor PCB ASSY. 10 T2(LT or TT) paper empty sensor PCB failure Replace the T2(LT or TT) paper empty sensor PCB ASSY. 11 T2LT control PCB failure Replace the T2LT control PCB ASSY. 12 TT control PCB failure Replace the TT control PCB ASSY. 13 TT low-voltage power supply PCB failure Replace the TT low-voltage power supply PCB ASSY. 14 Main PCB failure Replace the main PCB ASSY.

• Code: 7402
• Description: When printing from the paper tray 2, the registration front sensor or the T2TT jam sensor does not detect paper pass within the specified time after the T2(LT or TT) paper feed sensor detected paper pass.
• Remedy: • Remove the jammed paper. • Add the paper properly using the paper tray 2 paper guide. • Install the latest main firmware.
  1 Foreign object in the front of the machine Remove the foreign object. 2 Registration front actuator attachment failure Reattach the registration front actuator. 3 T2TT jam sensor attachment failure Reattach the T2TT jam sensor. 4 Connection failure of the registration front/rear sensor harness Reconnect the registration front/rear sensor harness. 5 Connection failure of the T2TT jam sensor harness Reconnect the T2TT jam sensor harness. 6 Connection failure of the TT control PCB harness Reconnect the TT control PCB harness. 7 Connection failure of the T2LT control PCB harness Reconnect the T2LT control PCB harness. 8 Connection failure of the T2LT release clutch harness Reconnect the T2LT release clutch harness. 9 T2LT release clutch failure Replace the T2LT release clutch. 10 Registration front/rear sensor PCB failure Replace the registration front/rear sensor PCB ASSY. 11 T2TT jam sensor PCB failure Replace the T2TT jam sensor PCB ASSY. 12 TT control PCB failure Replace the TT control PCB ASSY. 13 T2LT control PCB failure Replace the T2LT control PCB ASSY. 14 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 15 Damaged gears in the paper feeding system Replace the main frame L ASSY. 16 Damaged gears in the LT paper feeding system Replace the LT. 17 Damaged gears in the TT paper feeding system Replace the TT. 18 Main PCB failure Replace the main PCB ASSY.

• Code: 7501
• Description: When printing from the paper tray 3, the T3(LT or TT) paper feed sensor does not detect paper pass within the specified time while the T3(LT or TT) paper empty sensor detects some paper set.
• Remedy: • Remove the jammed paper. • Add the paper properly using the paper tray 3 paper guide.
  1 Foreign object in the front of the machine Remove the foreign object. 2 Malfunction of the LT control PCB or TT control PCB Install the latest main firmware. 3 T3(LT or TT) paper pick up roller holder attachment failure Reattach the T3(LT or TT) paper pick up roller holder. 4 T3(LT or TT) paper feed actuator attachment failure Reattach the T3(LT or TT) paper feed actuator. 5 Connection failure of the T3(LT or TT) pickup clutch harness Reconnect the T3(LT or TT) pickup clutch harness. 6 Connection failure of the T3(LT or TT) paper feed sensor harness Reconnect the T3(LT or TT) paper feed sensor harness. 7 PF kit 3 failure Replace the PF kit 3. 8 T3(LT or TT) pickup clutch failure Replace the T3(LT or TT) pickup clutch. 9 T3(LT or TT) paper feed sensor PCB failure Replace the T3(LT or TT) paper feed sensor PCB ASSY. 10 T3(LT or TT) paper empty sensor PCB failure Replace the T3(LT or TT) paper empty sensor PCB ASSY. 11 T3LT control PCB failure Replace the T3LT control PCB ASSY. 12 TT control PCB failure Replace the TT control PCB ASSY. 13 TT low-voltage power supply PCB failure Replace the TT low-voltage power supply PCB ASSY. 14 Main PCB failure Replace the main PCB ASSY.

• Code: 7502
• Description: When printing from the paper tray 3, the registration front sensor or the T2/T3TT jam sensor does not detect paper pass within the specified time after the T3(LT or TT) paper feed sensor detected paper pass.
• Remedy: • Remove the jammed paper. • Add the paper properly using the paper tray 3 paper guide. • Install the latest main firmware.
  1 Foreign object in the front of the machine Remove the foreign object. 2 Registration front actuator attachment failure Reattach the registration front actuator. 3 T2/T3TT jam sensor attachment failure Reattach the T2/T3TT jam sensor. 4 Connection failure of the registration front/rear sensor harness Reconnect the registration front/rear sensor harness. 5 Connection failure of the T2/ T3TT jam sensor harness Reconnect the T2/T3TT jam sensor harness. 6 Connection failure of the TT control PCB harness Reconnect the TT control PCB harness. 7 Connection failure of the T2/ T3LT control PCB harness Reconnect the T2/T3LT control PCB harness. 8 Connection failure of the T2/ T3LT release clutch harness Reconnect the T2/T3LT release clutch harness. 9 Connection failure of the T3TT release clutch harness Reconnect the T3TT release clutch harness. 10 T2/T3LT release clutch failure Replace the T2/T3LT release clutch. 11 T3TT release clutch failure Replace the T3TT release clutch. 12 Registration front/rear sensor PCB failure Replace the registration front/rear sensor PCB ASSY. 13 T2/T3TT jam sensor PCB failure Replace the T2/T3TT jam sensor PCB ASSY. 14 TT control PCB failure Replace the TT control PCB ASSY. 15 T2/T3LT control PCB failure Replace the T2/T3LT control PCB ASSY. 16 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 17 Damaged gears in the paper feeding system Replace the main frame L ASSY. 18 Damaged gears in an LT paper feeding system Replace the LT. 19 Damaged gears in the TT paper feeding system Replace the TT. 20 Main PCB failure Replace the main PCB ASSY.

• Code: 7601
• Description: When printing from the paper tray 4, the T4(LT or TT) paper feed sensor does not detect paper pass within the specified time while the T4(LT or TT) paper empty sensor detects some paper set.
• Remedy: • Remove the jammed paper. • Add the paper properly using the paper tray 4 paper guide.
  1 Foreign object in the front of the machine Remove the foreign object. 2 Malfunction of the LT control PCB or TT control PCB Install the latest main firmware. 3 T4(LT or TT) paper pick up roller holder attachment failure Reattach the T4(LT or TT) paper pick up roller holder. 4 T4(LT or TT) paper feed actuator attachment failure Reattach the T4(LT or TT) paper feed actuator. 5 Connection failure of the T4(LT or TT) pickup clutch harness Reconnect the T4(LT or TT) pickup clutch harness. 6 Connection failure of the T4(LT or TT) paper feed sensor harness Reconnect the T4(LT or TT) paper feed sensor harness. 7 PF kit 4 failure Replace the PF kit 4. 8 T4(LT or TT) pickup clutch failure Replace the T4(LT or TT) pickup clutch. 9 T4(LT or TT) paper feed sensor PCB failure Replace the T4(LT or TT) paper feed sensor PCB ASSY. 10 T4(LT or TT) paper empty sensor PCB failure Replace the T4(LT or TT) paper empty sensor PCB ASSY. 11 T4LT control PCB failure Replace the T4LT control PCB ASSY. 12 TT control PCB failure Replace the TT control PCB ASSY. 13 TT low-voltage power supply PCB failure Replace the TT low-voltage power supply PCB ASSY. 14 Main PCB failure Replace the main PCB ASSY.

• Code: 7602
• Description: When printing from the paper tray 4, the registration front sensor or the T2/T3/T4TT jam sensor does not detect paper pass within the specified time after the T4(LT or TT) paper feed sensor detected paper pass.
• Remedy: • Remove the jammed paper. • Add the paper properly using the paper tray 4 paper guide. • Install the latest main firmware.
  1 Foreign object in the front of the machine Remove the foreign object. 2 Registration front actuator attachment failure Reattach the registration front actuator. 3 T2/T3/T4TT jam sensor attachment failure Reattach the T2/T3/T4TT jam sensor. 4 Connection failure of the registration front/rear sensor harness Reconnect the registration front/rear sensor harness. 5 Connection failure of the T2/T3/ T4TT jam sensor harness Reconnect the T2/T3/T4TT jam sensor harness. 6 Connection failure of the TT control PCB harness Reconnect the TT control PCB harness. 7 Connection failure of the T2/T3/ T4LT control PCB harness Reconnect the T2/T3/T4LT control PCB harness. 8 Connection failure of the T2/T3/ T4LT release clutch harness Reconnect the T2/T3/T4LT release clutch harness. 9 Connection failure of the T3/ T4TT release clutch harness Reconnect the T3/T4TT release clutch harness. 10 T2/T3/T4LT release clutch failure Replace the T2/T3/T4LT release clutch. 11 T3/T4TT release clutch failure Replace the T3/T4TT release clutch. 12 Registration front/rear sensor PCB failure Replace the registration front/rear sensor PCB. 13 T2/T3/T4TT jam sensor PCB failure Replace the T2/T3/T4TT jam sensor PCB ASSY. 14 TT control PCB failure Replace the TT control PCB ASSY. 15 T2/T3/T4LT control PCB failure Replace the T2/T3/T4LT control PCB ASSY. 16 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 17 Damaged gears in the paper feeding system Replace the main frame L ASSY. 18 Damaged gears in an LT paper feeding system Replace the LT. 19 Damaged gears in the TT paper feeding system Replace the TT. 20 Main PCB failure Replace the main PCB ASSY.

• Code: 7701
• Description: When printing from the paper tray 5, the T5TT paper feed sensor does not detect paper pass within the specified time while the T5TT paper empty sensor detects some paper set.
• Remedy: • Remove the jammed paper. • Add the paper properly using the paper tray 5 paper guide.
  1 Foreign object in the front of the machine Remove the foreign object. 2 Malfunction of the TT control PCB Install the latest main firmware. 3 T5TT paper pick up roller holder attachment failure Reattach the T5TT paper pick up roller holder. 4 T5TT paper feed actuator attachment failure Reattach the T5TT paper feed actuator. 5 Connection failure of the T5TT pickup clutch harness Reconnect the T5TT pickup clutch harness. 6 Connection failure of the T5TT paper feed sensor harness Reconnect the T5TT paper feed sensor harness. 7 PF kit 5 failure Replace the PF kit 5. 8 T5TT pickup clutch failure Replace the T5TT pickup clutch. 9 T5TT paper feed sensor PCB failure Replace the T5TT paper feed sensor PCB ASSY. 10 T5TT paper empty sensor PCB failure Replace the T5TT paper empty sensor PCB ASSY. 11 TT control PCB failure Replace the TT control PCB ASSY. 12 TT low-voltage power supply PCB failure Replace the TT low-voltage power supply PCB ASSY. 13 Main PCB failure Replace the main PCB ASSY.

• Code: 7702
• Description: When printing from the paper tray 5, the registration front sensor or the T2/T3/T4/T5TT jam sensor does not detect paper pass within the specified time after the T5TT paper feed sensor detected paper pass.
• Remedy: • Remove the jammed paper. • Add the paper properly using the paper tray 5 paper guide. • Install the latest main firmware.
  1 Foreign object in the front of the machine Remove the foreign object. 2 Registration front actuator attachment failure Reattach the registration front actuator. 3 T2/T3/T4/T5TT jam sensor attachment failure Reattach the T2/T3/T4/T5TT jam sensor. 4 Connection failure of the registration front/rear sensor harness Reconnect the registration front/rear sensor harness. 5 Connection failure of the T2/T3/ T4/T5TT jam sensor harness Reconnect the T2/T3/T4/T5TT jam sensor harness. 6 Connection failure of the TT control PCB harness Reconnect the TT control PCB harness. 7 Connection failure of the T3/T4/ T5TT release clutch harness Reconnect the T3/T4/T5TT release clutch harness. 8 T3/T4/T5TT release clutch failure Replace the T3/T4/T5TT release clutch. 9 Registration front/rear sensor PCB failure Replace the registration front/rear sensor PCB ASSY. 10 T2/T3/T4/T5TT jam sensor PCB failure Replace the T2/T3/T4/T5TT jam sensor PCB ASSY. 11 TT control PCB failure Replace the TT control PCB ASSY. 12 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 13 Damaged gears in the TT paper feeding system Replace the TT. 14 Main PCB failure Replace the main PCB ASSY.

• Code: 7800
• Description: The registration front sensor does not detect paper pass within the specified time after the first side was printed in duplex printing mode.
• Remedy: • Remove the jammed paper. • Close the back cover correctly. • Attach the duplex tray correctly.
  1 Foreign object in the rear of the machine or duplex tray Remove the foreign object. 2 Twisted TT frame Loosen the nine screws shown in the figure below and tighten them again. 3 Connection failure of the eject motor harness Reconnect the eject motor harness. 4 MX flapper attachment failure Reattach the MX flapper. 5 MX switching solenoid failure Replace the MX switching solenoid. 6 Duplex tray failure Replace the duplex tray. 7 Eject motor failure Replace the eject motor. 8 Damaged gears in the paper feeding system Replace the main frame L ASSY. 9 Paper eject roller failure Replace the paper eject roller. 10 Main PCB failure Replace the main PCB ASSY.

• Code: 7B01
• Description: The MX jam lower sensor does not detect paper pass within the specified time after the eject sensor detected paper pass.
• Remedy: • Remove the jammed paper. • Close the back cover correctly.
  1 Foreign object in the rear of the machine Remove the foreign object. 2 MX flapper attachment failure Reattach the MX flapper. 3 Connection failure of the MX jam lower sensor harness Reconnect the MX jam lower sensor harness. 4 Connection failure of the MX motor harness Reconnect the MX motor harness. 5 MX switching solenoid failure Replace the MX switching solenoid. 6 MX motor failure Replace the MX motor. 7 MX control PCB failure Replace the MX control PCB ASSY. 8 Main PCB failure Replace the main PCB ASSY.

• Code: 7B02
• Description: The MX 1bin stack sensor does not detect paper pass within the specified time after the MX jam lower sensor detected paper pass.
• Remedy: • Remove the jammed paper. • Close the MX back cover correctly.
  1 Foreign object in the rear of the machine Remove the foreign object. 2 MX flapper 1 attachment failure Reattach the MX flapper 1. 3 MX 1bin stack actuator attachment failure Reattach the MX 1bin stack actuator. 4 Connection failure of the MX flapper 1 solenoid harness Reconnect the MX flapper 1 solenoid harness. 5 Connection failure of the MX 1bin stack sensor harness Reconnect the MX 1bin stack sensor harness. 6 Connection failure of the MX relay PCB harness Reconnect the MX relay PCB harness. 7 MX 1bin stack sensor failure Replace the MX 1bin stack sensor. 8 MX flapper 1 solenoid failure Replace the MX flapper 1 solenoid. 9 MX relay PCB failure Replace the MX relay PCB ASSY. 10 MX control PCB failure Replace the MX control PCB ASSY. 11 Main PCB failure Replace the main PCB ASSY.

• Code: 7B03
• Description: The MX 2bin stack sensor does not detect paper pass within the specified time after the MX jam lower sensor detected paper pass.
• Remedy: • Remove the jammed paper. • Close the MX back cover correctly.
  1 Foreign object in the rear of the machine Remove the foreign object. 2 MX flapper 1 or 2 attachment failure Reattach the MX flapper 1 or 2. 3 MX 2bin stack actuator attachment failure Reattach the MX 2bin stack actuator. 4 Connection failure of the MX flapper 2 solenoid harness Reconnect the MX flapper 2 solenoid harness. 5 Connection failure of the MX 2bin stack sensor harness Reconnect the MX 2bin stack sensor harness. 6 Connection failure of the MX relay PCB harness Reconnect the MX relay PCB harness. 7 MX 2bin stack sensor failure Replace the MX 2bin stack sensor. 8 MX flapper 1 or 2 solenoid failure Replace the MX flapper 1 or 2 solenoid. 9 MX relay PCB failure Replace the MX relay PCB ASSY. 10 MX control PCB failure Replace the MX control PCB ASSY. 11 Main PCB failure Replace the main PCB ASSY.

• Code: 7B04
• Description: The MX 3bin stack sensor does not detect paper pass within the specified time after the MX jam upper sensor detected paper pass.
• Remedy: • Remove the jammed paper. • Close the MX back cover correctly.
  1 Foreign object in the rear of the machine Remove the foreign object. 2 MX flapper 3 attachment failure Reattach the MX flapper 3. 3 MX 3bin stack actuator attachment failure Reattach the MX 3bin stack actuator. 4 Connection failure of the MX flapper 3 solenoid harness Reconnect the MX flapper 3 solenoid harness. 5 Connection failure of the MX 3bin stack sensor harness Reconnect the MX 3bin stack sensor harness. 6 Connection failure of the MX relay PCB harness Reconnect the MX relay PCB harness. 7 MX 3bin stack sensor failure Replace the MX 3bin stack sensor. 8 MX flapper 3 solenoid failure Replace the MX flapper 3 solenoid. 9 MX relay PCB failure Replace the MX relay PCB ASSY. 10 MX control PCB failure Replace the MX control PCB ASSY. 11 Main PCB failure Replace the main PCB ASSY.

• Code: 7B05
• Description: The MX 4bin stack sensor does not detect paper pass within the specified time after the MX jam upper sensor detected paper pass.
• Remedy: • Remove the jammed paper. • Close the MX back cover correctly.
  1 Foreign object in the rear of the machine Remove the foreign object. 2 MX flapper 3 attachment failure Reattach the MX flapper 3. 3 MX 4bin stack actuator attachment failure Reattach the MX 4bin stack actuator. 4 Connection failure of the MX 4bin stack sensor harness Reconnect the MX 4bin stack sensor harness. 5 Connection failure of the MX relay PCB harness Reconnect the MX relay PCB harness. 6 MX 4bin stack sensor failure Replace the MX 4bin stack sensor. 7 MX relay PCB failure Replace the MX relay PCB ASSY. 8 MX control PCB failure Replace the MX control PCB ASSY. 9 Main PCB failure Replace the main PCB ASSY.

• Code: 7F00
• Description: MX(2 or 4) bin sensor detected that the only one of the two removable plates is removed from the MX.
• Remedy: • Remove or attach both of the two removable plates. • Reattach the removable plates.
  1 Connection failure of the MX 2bin detection sensor harness or MX 4bin detection sensor harness Reconnect the MX 2bin detection sensor harness or MX 4bin detection sensor harness. 2 MX 2bin detection sensor or MX 4bin detection sensor failure Replace the MX 2bin detection sensor or MX 4bin detection sensor. 3 MX control PCB failure Replace the MX control PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 8501
• Description: When printing from paper tray 1, 2, 3, 4 or 5, the T1 paper feed sensor detected open paper tray 1 (before registering printing data to engine).
• Remedy: • Close the appropriate paper tray correctly.
  1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 An LT/TT paper feed actuator coming off or caught in some sections of the machine Reattach the appropriate LT/TT paper feed actuator. 3 An LT/TT paper feed sensor failure Replace the appropriate LT/TT paper feed sensor PCB ASSY. 4 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 5 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 6 TT relay PCB failure Replace a TT relay PCB ASSY. 7 TT control PCB failure Replace the TT control PCB ASSY. 8 Main PCB failure Replace the main PCB ASSY.

• Code: 8502
• Description: When printing from paper tray 2, 3, 4 or 5, the T2(LT or TT) paper feed sensor detected open paper tray 2 (before registering printing data to engine).
• Remedy: • Close the appropriate paper tray correctly.
  1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 An LT/TT paper feed actuator coming off or caught in some sections of the machine Reattach the appropriate LT/TT paper feed actuator. 3 An LT/TT paper feed sensor failure Replace the appropriate LT/TT paper feed sensor PCB ASSY. 4 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 5 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 6 TT relay PCB failure Replace a TT relay PCB ASSY. 7 TT control PCB failure Replace the TT control PCB ASSY. 8 Main PCB failure Replace the main PCB ASSY.

• Code: 8503
• Description: When printing from paper tray 3, 4 or 5, the T3(LT or TT) paper feed sensor detected open paper tray 3 (before registering printing data to engine).
• Remedy: • Close the appropriate paper tray correctly.
  1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 An LT/TT paper feed actuator coming off or caught in some sections of the machine Reattach the appropriate LT/TT paper feed actuator. 3 An LT/TT paper feed sensor failure Replace the appropriate LT/TT paper feed sensor PCB ASSY. 4 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 5 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 6 TT relay PCB failure Replace a TT relay PCB ASSY. 7 TT control PCB failure Replace the TT control PCB ASSY. 8 Main PCB failure Replace the main PCB ASSY.

• Code: 8504
• Description: When printing from paper tray 4 or 5, the T4(LT or TT) paper feed sensor detected open paper tray 4 (before registering printing data to engine).
• Remedy: • Close the appropriate paper tray correctly.
  1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 An LT/TT paper feed actuator coming off or caught in some sections of the machine Reattach the appropriate LT/TT paper feed actuator. 3 An LT/TT paper feed sensor failure Replace the appropriate LT/TT paper feed sensor PCB ASSY. 4 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 5 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 6 TT relay PCB failure Replace a TT relay PCB ASSY. 7 TT control PCB failure Replace the TT control PCB ASSY. 8 Main PCB failure Replace the main PCB ASSY.

• Code: 8505
• Description: When printing from paper tray 1, 2, 3, 4 or 5, the T1 paper feed sensor detected open paper tray 1 (after registering printing data to engine).
• Remedy: • Close the appropriate paper tray correctly.
  1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 An LT/TT paper feed sensor failure Replace the appropriate LT/TT paper feed sensor PCB ASSY. 3 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 4 TT relay PCB failure Replace a TT relay PCB ASSY. 5 TT control PCB failure Replace the TT control PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY.

• Code: 8506
• Description: When printing from paper tray 2, 3, 4 or 5, the T2(LT or TT) paper feed sensor detected open paper tray 2 (after registering printing data to engine).
• Remedy: • Close the appropriate paper tray correctly.
  1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 An LT/TT paper feed sensor failure Replace the appropriate LT/TT paper feed sensor PCB ASSY. 3 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 4 TT relay PCB failure Replace a TT relay PCB ASSY. 5 TT control PCB failure Replace the TT control PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY.

• Code: 8507
• Description: When printing from paper tray 3, 4 or 5, the T3(LT or TT) paper feed sensor detected open paper tray 3 (after registering printing data to engine).
• Remedy: • Close the appropriate paper tray correctly.
  1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 An LT/TT paper feed sensor failure Replace the appropriate LT/TT paper feed sensor PCB ASSY. 3 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 4 TT relay PCB failure Replace a TT relay PCB ASSY. 5 TT control PCB failure Replace the TT control PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY.

• Code: 8508
• Description: When printing from paper tray 4 or 5, the T4(LT or TT) paper feed sensor detected open paper tray 4 (after registering printing data to engine).
• Remedy: • Close the appropriate paper tray correctly.
  1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 An LT/TT paper feed sensor failure Replace the appropriate LT/TT paper feed sensor PCB ASSY. 3 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 4 TT relay PCB failure Replace a TT relay PCB ASSY. 5 TT control PCB failure Replace the TT control PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY.

• Code: 8701
• Description: MX 1bin, 2bin, 3bin, or 4bin stack sensor or machine stack sensor detected the ejected paper full state at the start of printing.
• Remedy: • Remove the paper from all output trays.
  1 Malfunction of the MX control PCB Install the latest main firmware. 2 Machine stack sensor failure Replace the machine stack sensor. 3 MX control PCB failure Replace the MX control PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 8702
• Description: Machine stack sensor detected the eject paper full state at the start of printing when the machine output tray was selected as the output tray.
• Remedy: • Remove the paper from the machine output tray.
  1 Machine stack actuator coming off or caught in some sections of the machine Reattach the machine stack actuator. 2 Machine stack sensor failure Replace the machine stack sensor. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 8708
• Description: MX 1bin stack sensor detected the eject paper full state at the start of printing when the MX 1bin was selected as the output tray.
• Remedy: • Remove the paper from the appropriate tray.
  1 Malfunction of the MX control PCB Install the latest main firmware. 2 MX 1bin, 2bin, 3bin, or 4bin stack actuator coming off or caught in some sections of the machine Reattach the appropriate stack actuator. 3 MX 1bin, 2bin, 3bin, or 4bin stack sensor failure Replace the appropriate stack sensor. 4 MX control PCB failure Replace the MX control PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 8709
• Description: MX 2bin stack sensor detected the eject paper full state at the start of printing when the MX 2bin was selected as the output tray.
• Remedy: • Remove the paper from the appropriate tray.
  1 Malfunction of the MX control PCB Install the latest main firmware. 2 MX 1bin, 2bin, 3bin, or 4bin stack actuator coming off or caught in some sections of the machine Reattach the appropriate stack actuator. 3 MX 1bin, 2bin, 3bin, or 4bin stack sensor failure Replace the appropriate stack sensor. 4 MX control PCB failure Replace the MX control PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 870A
• Description: MX 3bin stack sensor detected the eject paper full state at the start of printing when the MX 3bin was selected as the output tray.
• Remedy: • Remove the paper from the appropriate tray.
  1 Malfunction of the MX control PCB Install the latest main firmware. 2 MX 1bin, 2bin, 3bin, or 4bin stack actuator coming off or caught in some sections of the machine Reattach the appropriate stack actuator. 3 MX 1bin, 2bin, 3bin, or 4bin stack sensor failure Replace the appropriate stack sensor. 4 MX control PCB failure Replace the MX control PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 870B
• Description: MX 4bin stack sensor detected the eject paper full state at the start of printing when the MX 4bin was selected as the output tray.
• Remedy: • Remove the paper from the appropriate tray.
  1 Malfunction of the MX control PCB Install the latest main firmware. 2 MX 1bin, 2bin, 3bin, or 4bin stack actuator coming off or caught in some sections of the machine Reattach the appropriate stack actuator. 3 MX 1bin, 2bin, 3bin, or 4bin stack sensor failure Replace the appropriate stack sensor. 4 MX control PCB failure Replace the MX control PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 870C
• Description: Machine stack sensor or MX 1bin stack sensor detected the eject paper full state at the start of printing when the MX 1bin was selected as the output tray and ‘Use Std. Tray when full’ setting was ON.
• Remedy: • Remove the paper from the appropriate output tray.
  1 Malfunction of the MX control PCB Install the latest main firmware. 2 MX 1bin, 2bin, 3bin, or 4bin stack actuator coming off or caught in some sections of the machine Reattach the appropriate stack actuator. 3 MX 1bin, 2bin, 3bin, or 4bin stack sensor failure Replace the appropriate stack sensor. 4 MX control PCB failure Replace the MX control PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 870D
• Description: Machine stack sensor or MX 2bin stack sensor detected the eject paper full state at the start of printing when the MX 2bin was selected as the output tray and ‘Use Std. Tray when full’ setting was ON.
• Remedy: • Remove the paper from the appropriate output tray.
  1 Malfunction of the MX control PCB Install the latest main firmware. 2 MX 1bin, 2bin, 3bin, or 4bin stack actuator coming off or caught in some sections of the machine Reattach the appropriate stack actuator. 3 MX 1bin, 2bin, 3bin, or 4bin stack sensor failure Replace the appropriate stack sensor. 4 MX control PCB failure Replace the MX control PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 870E
• Description: Machine stack sensor or MX 3bin stack sensor detected the eject paper full state at the start of printing when the MX 3bin was selected as the output tray and ‘Use Std. Tray when full’ setting was ON.
• Remedy: • Remove the paper from the appropriate output tray.
  1 Malfunction of the MX control PCB Install the latest main firmware. 2 MX 1bin, 2bin, 3bin, or 4bin stack actuator coming off or caught in some sections of the machine Reattach the appropriate stack actuator. 3 MX 1bin, 2bin, 3bin, or 4bin stack sensor failure Replace the appropriate stack sensor. 4 MX control PCB failure Replace the MX control PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 870F
• Description: Machine stack sensor or MX 4bin stack sensor detected the eject paper full state at the start of printing when the MX 4bin was selected as the output tray and ‘Use Std. Tray when full’ setting was ON.
• Remedy: • Remove the paper from the appropriate output tray.
  1 Malfunction of the MX control PCB Install the latest main firmware. 2 MX 1bin, 2bin, 3bin, or 4bin stack actuator coming off or caught in some sections of the machine Reattach the appropriate stack actuator. 3 MX 1bin, 2bin, 3bin, or 4bin stack sensor failure Replace the appropriate stack sensor. 4 MX control PCB failure Replace the MX control PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 8808
• Description: MX back cover sensor detected the open cover when the MX was selected as the output tray (before registering printing data to engine).
• Remedy: • Close the MX back cover correctly.
  1 MX back cover sensor attachment failure Reattach the MX back cover sensor. 2 Connection failure of the MX back cover sensor harness Reconnect the MX back cover sensor harness. 3 Damaged MX back cover Replace the MX back cover. 4 MX back cover sensor failure Replace the MX back cover sensor. 5 MX control PCB failure Replace the MX control PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY.

• Code: 8809
• Description: MX back cover sensor detected the open cover when the MX was selected as the output tray (after registering printing data to engine).
• Remedy: • Close the MX back cover correctly.
  1 MX back cover sensor attachment failure Reattach the MX back cover sensor. 2 Connection failure of the MX back cover sensor harness Reconnect the MX back cover sensor harness. 3 Damaged MX back cover Replace the MX back cover. 4 MX back cover sensor failure Replace the MX back cover sensor. 5 MX control PCB failure Replace the MX control PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY.

• Code: 8903
• Description: The back cover/duplex tray sensor detected that the cover was open when duplex printing is started. (Before registering printing data to engine)
• Remedy: • Close the back cover correctly. • Attach the duplex tray correctly.
  1 Back cover/duplex tray sensor attachment failure Reattach the back cover/duplex tray sensor. 2 Connection failure of the back cover/duplex tray sensor harness Reconnect the back cover/duplex tray sensor harness. 3 Damaged back cover Replace the back cover. 4 Damaged duplex tray Replace the duplex tray. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 8904
• Description: The back cover/duplex tray sensor detected that the cover was open during duplex printing. (After registering printing data to engine)
• Remedy: • Close the back cover correctly. • Attach the duplex tray correctly.
  1 Back cover/duplex tray sensor attachment failure Reattach the back cover/duplex tray sensor. 2 Connection failure of the back cover/duplex tray sensor harness Reconnect the back cover/duplex tray sensor harness. 3 Damaged back cover Replace the back cover. 4 Damaged duplex tray Replace the duplex tray. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 8A01
• Description: The registration rear sensor detected that the paper fed was smaller or larger than the specified size in duplex printing mode.
• Remedy: • Use specified paper.
  1 Registration rear actuator caught in some sections of the machine Reattach the registration rear actuator. 2 Registration rear sensor failure Replace the registration front/rear sensor PCB ASSY. 3 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 8B01
• Description: Detected that the TT was not turned ON.
• Remedy: • Turn ON the TT. • Reconnect the AC cord of the TT.
  1 Malfunction of the TT control PCB Install the latest main firmware. 2 Connection failure of the TT lowvoltage power supply PCB harness Reconnect the TT low-voltage power supply PCB harness. 3 TT AC cord breakage Replace the AC cord. 4 TT low-voltage power supply PCB failure Replace the TT low-voltage power supply PCB ASSY. 5 TT control PCB failure Replace the TT control PCB ASSY. 6 Main PCB failure Replace the main PCB ASSY.

• Code: 9001
• Description: When printing from the MP tray, the size of paper set in the MP tray does not match the size specified by the driver.
• Remedy: • Change the driver setting to be matched with the size of the paper set in the paper tray.
  1 Registration rear actuator caught in some sections of the machine Reattach the registration rear actuator. 2 Registration rear sensor failure Replace the registration front/rear sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 9002
• Description: When printing from the paper tray 1, the size of paper set in the paper tray 1 does not match the size specified by the driver.
• Remedy: • Change the driver setting to be matched with the size of the paper set in the paper tray.
  1 Registration rear actuator caught in some sections of the machine Reattach the registration rear actuator. 2 Registration rear sensor failure Replace the registration front/rear sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 9003
• Description: When printing from the paper tray 2, the size of paper set in the paper tray 2 does not match the size specified by the driver.
• Remedy: • Change the driver setting to be matched with the size of the paper set in the paper tray.
  1 Registration rear actuator caught in some sections of the machine Reattach the registration rear actuator. 2 Registration rear sensor failure Replace the registration front/rear sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 9003
• Description: When printing from the paper tray 2, the size of paper set in the paper tray 2 does not match the size specified by the driver.
• Remedy: • Change the driver setting to be matched with the size of the paper set in the paper tray.
  1 Registration rear actuator caught in some sections of the machine Reattach the registration rear actuator. 2 Registration rear sensor failure Replace the registration front/rear sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 9004
• Description: When printing from the paper tray 3, the size of paper set in the paper tray 3 does not match the size specified by the driver.
• Remedy: • Change the driver setting to be matched with the size of the paper set in the paper tray.
  1 Registration rear actuator caught in some sections of the machine Reattach the registration rear actuator. 2 Registration rear sensor failure Replace the registration front/rear sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 9005
• Description: When printing from the paper tray 4, the size of paper set in the paper tray 4 does not match the size specified by the driver.
• Remedy: • Change the driver setting to be matched with the size of the paper set in the paper tray.
  1 Registration rear actuator caught in some sections of the machine Reattach the registration rear actuator. 2 Registration rear sensor failure Replace the registration front/rear sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 9006
• Description: When printing from the paper tray 5, the size of paper set in the paper tray 5 does not match the size specified by the driver.
• Remedy: • Change the driver setting to be matched with the size of the paper set in the paper tray.
  1 Registration rear actuator caught in some sections of the machine Reattach the registration rear actuator. 2 Registration rear sensor failure Replace the registration front/rear sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 9201
• Description: When printing from the MP tray, paper type setting in the machine does not match the setting in the driver.
• Remedy: • Use the same paper type setting for the machine and driver.
  1 Malfunction of the main PCB Install the latest main firmware. 2 Main PCB failure Replace the main PCB ASSY.

• Code: 9202
• Description: When printing from the paper tray 1, paper type setting in the machine does not match the setting in the driver.
• Remedy: • Use the same paper type setting for the machine and driver.
  1 Malfunction of the main PCB Install the latest main firmware. 2 Main PCB failure Replace the main PCB ASSY.

– Get more error code list with quick guide to fix printer product, click here
– About get help with reseting Epson inkpad or others, click here

• Code: 9203
• Description: When printing from the paper tray 2, paper type setting in the machine does not match the setting in the driver.
• Remedy: • Use the same paper type setting for the machine and driver.
  1 Malfunction of the main PCB Install the latest main firmware. 2 Main PCB failure Replace the main PCB ASSY.

• Code: 9204
• Description: When printing from the paper tray 3, paper type setting in the machine does not match the setting in the driver.
• Remedy: • Use the same paper type setting for the machine and driver.
  1 Malfunction of the main PCB Install the latest main firmware. 2 Main PCB failure Replace the main PCB ASSY.

• Code: 9205
• Description: When printing from the paper tray 4, paper type setting in the machine does not match the setting in the driver.
• Remedy: • Use the same paper type setting for the machine and driver.
  1 Malfunction of the main PCB Install the latest main firmware. 2 Main PCB failure Replace the main PCB ASSY.

• Code: 9206
• Description: When printing from the paper tray 5, paper type setting in the machine does not match the setting in the driver.
• Remedy: • Use the same paper type setting for the machine and driver.
  1 Malfunction of the main PCB Install the latest main firmware. 2 Main PCB failure Replace the main PCB ASSY.

• Code: 9301
• Description: When printing from the MP tray, the MP paper empty sensor detected that there was no paper set in the MP tray.
• Remedy: • Set paper in the appropriate paper tray.
  1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 Connection failure of a LT/TT paper empty sensor harness Reconnect the appropriate LT/TT paper empty sensor harness. 3 An LT/TT paper empty actuator caught in some sections of the machine Reattach the appropriate LT/TT paper empty actuator. 4 An LT/TT paper empty sensor PCB failure Replace the appropriate LT/TT paper empty sensor PCB ASSY. 5 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 6 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 7 TT relay PCB failure Replace a TT relay PCB ASSY. 8 TT control PCB failure Replace the TT control PCB ASSY. 9 Main PCB failure Replace the main PCB ASSY.

• Code: 9302
• Description: When printing from paper tray 1, the T1 paper empty sensor or the T1 paper feed sensor detected that there was no paper set in paper tray 1.
• Remedy: • Set paper in the appropriate paper tray.
  1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 Connection failure of a LT/TT paper empty sensor harness Reconnect the appropriate LT/TT paper empty sensor harness. 3 An LT/TT paper empty actuator caught in some sections of the machine Reattach the appropriate LT/TT paper empty actuator. 4 An LT/TT paper empty sensor PCB failure Replace the appropriate LT/TT paper empty sensor PCB ASSY. 5 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 6 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 7 TT relay PCB failure Replace a TT relay PCB ASSY. 8 TT control PCB failure Replace the TT control PCB ASSY. 9 Main PCB failure Replace the main PCB ASSY.

• Code: 9303
• Description: When printing from paper tray 2, the T2(LT or TT) paper empty sensor detected that there was no paper set in paper tray 2.
• Remedy: • Set paper in the appropriate paper tray.
  1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 Connection failure of a LT/TT paper empty sensor harness Reconnect the appropriate LT/TT paper empty sensor harness. 3 An LT/TT paper empty actuator caught in some sections of the machine Reattach the appropriate LT/TT paper empty actuator. 4 An LT/TT paper empty sensor PCB failure Replace the appropriate LT/TT paper empty sensor PCB ASSY. 5 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 6 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 7 TT relay PCB failure Replace a TT relay PCB ASSY. 8 TT control PCB failure Replace the TT control PCB ASSY. 9 Main PCB failure Replace the main PCB ASSY.

• Code: 9304
• Description: When printing from paper tray 3, the T3(LT or TT) paper empty sensor detected that there was no paper set in paper tray 3.
• Remedy: • Set paper in the appropriate paper tray.
  1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 Connection failure of a LT/TT paper empty sensor harness Reconnect the appropriate LT/TT paper empty sensor harness. 3 An LT/TT paper empty actuator caught in some sections of the machine Reattach the appropriate LT/TT paper empty actuator. 4 An LT/TT paper empty sensor PCB failure Replace the appropriate LT/TT paper empty sensor PCB ASSY. 5 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 6 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 7 TT relay PCB failure Replace a TT relay PCB ASSY. 8 TT control PCB failure Replace the TT control PCB ASSY. 9 Main PCB failure Replace the main PCB ASSY.

• Code: 9305
• Description: When printing from paper tray 4, the T4(LT or TT) paper empty sensor detected that there was no paper set in paper tray 4.
• Remedy: • Set paper in the appropriate paper tray.
  1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 Connection failure of a LT/TT paper empty sensor harness Reconnect the appropriate LT/TT paper empty sensor harness. 3 An LT/TT paper empty actuator caught in some sections of the machine Reattach the appropriate LT/TT paper empty actuator. 4 An LT/TT paper empty sensor PCB failure Replace the appropriate LT/TT paper empty sensor PCB ASSY. 5 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 6 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 7 TT relay PCB failure Replace a TT relay PCB ASSY. 8 TT control PCB failure Replace the TT control PCB ASSY. 9 Main PCB failure Replace the main PCB ASSY.

• Code: 9306
• Description: When printing from paper tray 5, the T5TT paper empty sensor detected that there was no paper set in paper tray 5.
• Remedy: • Set paper in the appropriate paper tray.
  1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 Connection failure of a LT/TT paper empty sensor harness Reconnect the appropriate LT/TT paper empty sensor harness. 3 An LT/TT paper empty actuator caught in some sections of the machine Reattach the appropriate LT/TT paper empty actuator. 4 An LT/TT paper empty sensor PCB failure Replace the appropriate LT/TT paper empty sensor PCB ASSY. 5 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 6 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 7 TT relay PCB failure Replace a TT relay PCB ASSY. 8 TT control PCB failure Replace the TT control PCB ASSY. 9 Main PCB failure Replace the main PCB ASSY.

• Code: 9309
• Description: Detected that there was no paper set in all trays when TrayAuto was selected for printing.
• Remedy: • Set paper in the paper tray.
  1 Malfunction of an LT control PCB or TT control PCB Install the latest main firmware. 2 Connection failure of an LT/TT paper empty sensor harness Reconnect the appropriate LT/TT paper empty sensor harness. 3 Connection failure of the T1 paper feed sensor harness Reconnect the T1 paper feed sensor harness. (Models with 250-sheet only) 4 An LT/TT paper empty actuator caught in some sections of the machine Reattach the appropriate LT/TT paper empty actuator. 5 T1 paper feed actuator caught in some sections of the machine Reattach the T1 paper feed actuator. (Models with 250-sheet only) 6 Abrasion of a PF kit Replace the appropriate PF kit. 7 An LT/TT paper empty sensor PCB failure Replace the appropriate LT/TT paper empty sensor PCB ASSY. 8 T1 paper feed sensor PCB failure Replace the T1 paper feed sensor PCB ASSY. (Models with 250-sheet only) 9 T1, T2, or T3(LT or TT) pickup clutch failure Replace the T1, T2, or T3(LT or TT) pickup clutch. 10 Paper feed motor failure Replace the paper feed motor. (Models with 250-sheet only) 11 High-voltage power supply PCB failure Replace the high-voltage power supply PCB ASSY. 12 An LT control PCB failure Replace the appropriate LT control PCB ASSY. 13 TT relay PCB failure Replace a TT relay PCB ASSY. 14 TT control PCB failure Replace the TT control PCB ASSY. 15 Damaged gears in the paper feeding system Replace the main frame L ASSY. (Models with 250-sheet only) 16 Main PCB failure Replace the main PCB ASSY.

• Code: 9400
• Description: Firmware version of the main PCB is older than that of the TT, MX and LT.
• Remedy: • Install the latest main firmware.
  1 Main firmware version and firmware version of the TT, MX and LT do not match Install the latest main firmware.

• Code: 9701
• Description: A tray set to duplex printing-incompatible size was specified in duplex printing.
• Remedy: • Select the specified paper size in the driver and set paper with the same size to the specified paper tray.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: 9702
• Description: When printing from paper tray 1, a paper size not supported for paper tray 1 was specified from the driver.
• Remedy: • Select the specified paper size in the driver and set paper with the same size to the specified paper tray.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: 9703
• Description: When printing from paper tray 2, a paper size not supported for paper tray 2 was specified from the driver.
• Remedy: • Select the specified paper size in the driver and set paper with the same size to the specified paper tray.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: 9704
• Description: When printing from paper tray 3, a paper size not supported for paper tray 3 was specified from the driver.
• Remedy: • Select the specified paper size in the driver and set paper with the same size to the specified paper tray.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: 9705
• Description: When printing from paper tray 4, a paper size not supported for paper tray 4 was specified from the driver.
• Remedy: • Select the specified paper size in the driver and set paper with the same size to the specified paper tray.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: 9706
• Description: When printing from paper tray 5, a paper size not supported for paper tray 5 was specified from the driver.
• Remedy: • Select the specified paper size in the driver and set paper with the same size to the specified paper tray.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: C001
• Description: Access request to the server timed out because the server address was wrong, network was not connected, or server was not working.
• Remedy: • Refer to the online User’s Guide to set the network again. • Check the LAN cable routing. • Check the wireless LAN settings.
  1 Connection failure of the wireless LAN PCB connector Reconnect the wireless LAN PCB connector. 2 Wireless LAN PCB failure Replace the wireless LAN PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: C002
• Description: User authentication error due to wrong user name, wrong password, or date and time was not synchronized between the machine and server.
• Remedy: • Refer to the online User’s Guide to set the network again. • Check the LAN cable routing. • Check the wireless LAN settings.
  1 Connection failure of the wireless LAN PCB connector Reconnect the wireless LAN PCB connector. 2 Wireless LAN PCB failure Replace the wireless LAN PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: C003
• Description: Cannot access to the file because the directory name is wrong, writing into directory is not permitted, or writing into file is locked or not permitted.
• Remedy: • Refer to the online User’s Guide to set the network again. • Check the LAN cable routing. • Check the wireless LAN settings.
  1 Connection failure of the wireless LAN PCB connector Reconnect the wireless LAN PCB connector. 2 Wireless LAN PCB failure Replace the wireless LAN PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: C004
• Description: Cannot acquire current time which is required for user authentication because the time has not been acquired.
• Remedy: • Refer to the online User’s Guide to set the network again. • Check the LAN cable routing. • Check the wireless LAN settings.
  1 Connection failure of the wireless LAN PCB connector Reconnect the wireless LAN PCB connector. 2 Wireless LAN PCB failure Replace the wireless LAN PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: C100
• Description: Failed to save data to a USB flash memory.
• Remedy: • Change the USB flash memory. • Check if there is sufficient memory in the USB flash memory.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: C700
• Description: There is insufficient memory to expand PC print data.
  Memo: • HL-L5000D (Except for Iran), HL-5580D, HL-5585D: Main Firmware D001GJ_D.djf (ver.1.17) HL-L5000D (For Iran): Main Firmware D004PT_C.djf (ver.1.08) HL-L5100DN, HL-L5100DNT, HL-5590DN, HL-L5102DW, HL-L5200DW, HL-L5200DWT, HL-L5202DW: Main Firmware D001GH_F.djf (ver.1.19) In case of firmware version before than above is installed, error code C700 (Out of Memory) is displayed on LCD when main firmware is installed by the maintenance driver.
• Remedy: • Print the print data stored in the memory. • Divide the print data and print them separately.
  1 Unable to use the maintenance driver Install the latest main firmware by the printer driver. 2 Main PCB failure Replace the main PCB ASSY.

• Code: C800
• Description: The memory size allotted for Secure Print was exceeded when saving Secure Print data.
• Remedy: • Print the print data stored in the memory. • Divide the print data and print them separately.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: D800
• Description: An error occurred while initializing the touch panel.
• Remedy: 1 Panel firmware version and main firmware version do not match Install the latest main firmware. 2 Connection failure of the panel PCB flat cable Reconnect the panel PCB flat cable. 3 LCD relay PCB failure Replace the LCD panel ASSY. 4 Main PCB failure Replace the main PCB ASSY.

• Code: E000
• Description: An error occurred in the ROM check sum.
• Remedy: 1 Malfunction of the main firmware Install the latest main firmware. 2 Main PCB failure Replace the main PCB ASSY.

• Code: E100
• Description: Program error
• Remedy: 1 Malfunction of the main firmware Install the latest main firmware. 2 Main PCB failure Replace the main PCB ASSY.

• Code: E500
• Description: An error occurred during access to the DRAM in the main PCB ASSY.
• Remedy: 1 Malfunction of the main firmware Install the latest main firmware. 2 Main PCB failure Replace the main PCB ASSY.

• Code: E600
• Description: Write error in the EEPROM of the main PCB ASSY
• Remedy: 1 Malfunction of the main firmware Install the latest main firmware. 2 Main PCB failure Replace the main PCB ASSY.

• Code: E701
• Description: System error in the flash ROM
• Remedy: 1 Malfunction of the main firmware Install the latest main firmware. 2 Main PCB failure Replace the main PCB ASSY.

• Code: E702
• Description: Read error in the flash ROM
• Remedy: 1 Malfunction of the main firmware Install the latest main firmware. 2 Main PCB failure Replace the main PCB ASSY.

• Code: E900
• Description: An error occurred while initializing the NFC.
• Remedy: 1 Connection failure of the panel PCB flat cable Reconnect the panel PCB flat cable. 2 Connection failure of the NFC PCB flat cable Reconnect the NFC PCB flat cable. 3 Panel PCB failure Replace the panel PCB ASSY. 4 NFC PCB failure Replace the NFC PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: EC00
• Description: A USB device not within the specification is connected to the USB terminal, resulting in over current.
• Remedy: • Disconnect the USB device from the USB flash memory port and turn the machine OFF. Turn the machine ON again after a while. • Replace the USB device with a different one.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: F900
• Description: The spec code was not entered correctly.
• Remedy: 1 The power was turned OFF while function code 74 was running. Reenter the spec code. 2 Main PCB failure Replace the main PCB ASSY.

About Canon Servie Tool V5610

– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.

– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.

Canon Service Tool V5610 Functions

– Fix Canon printer 7 times/ 8 times red light blinking:

– Fix Canon printer error code: 5B00, 5B01, 1700, 1701

Enter Service Mode on Canon Printer

1. Turn off a printer
2. Press and hold the Resume/Cancel/Stop button
3. Press and hold the ON button (do not release both buttons)
4. Release the Resume/Cancel/Stop button (do not release the ON button)
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
For more information about Canon Serice Tool V5610

– Get more information about Epson XP 15000 troubleshooting, click here
– Buy cheap key of Epson WIC Reset Tool, CLICK HERE
– Key Epson Adjustment Program, CLICK HERE
https://dnasofts.com/download-epson-xp-6100-driver-firmware-and-manuals/

Contact us to get support with Brother HL5595DNH Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
Or click here to get more ways.

Source:
https://dnasofts.com
https://shop.nguyendangnam.com/