Xerox Phaser 3115 error and solving error codes
– Compatible Printer model: Xerox Phaser 3115
– Xerox Phaser 3115 Error Codes with quick guides:
- Code: -1
- Description: All LEDs blinking (Fuser Error) 1. All the lamps on the operator panel blink. 2. Gear of the fuser does not work and breaks away melt away. When printing, motor breaks away from its place due to defective fuser gear.
- Causes: 1. Check if the thermostat, AC wire and Heat Lamp is open. 2. Check if the thermistor sensor is in place. 3. Check if the heat lamp works properly. 4. Check if the overheat circuit works properly. 5. The fuser gear is defective due to melting away.
- Troubleshooting Guides: 1. If the thermostat is open replace the fuser and check following items. 2. If the thermistor sensor device is located deep in the sponge, replace the fuser. 3. Check if the circuit of overheat mode works properly. 4. Run DCU mode : Perform DCU diagnostic code 10.
- Code: -2
- Description: All LEDs blinking (Scan Error) 1. All lamps on the operator panel blink.
- Causes: DCU Mode : Perform DCU diagnostic code 05. If the DCU error code 95 is displayed, replace LSU.
- Troubleshooting Guides: Replace LSU. If you cannot solve the problem after you replace LSU, replace the main board.
- Code: 60, 62, 68
- Description: Fuser Error
- Causes: The error in the fuser occurred. There is a short circuit in the thermistor and the thermostat while printing, Low Temperature Error occurs. • 60: Open Fuser Error • 62: Low Heat Error • 68: Over Heat Error
- Troubleshooting Guides: 1. If the thermostat is open replace the fuser and check following items. 2. If the thermistor sensor device is located deep in the sponge, replace the fuser. 3. Check if the circuit of overheat mode works properly. 4. Run DCU mode : Perform DCU diagnostic code 10.
- Code: 64
- Description: Cover Open
- Causes: The Printer Cover is open or Toner Cartridge not installed.
- Troubleshooting Guides:
- Code: 70
- Description: No Paper
- Causes: No paper in the paper cassette.
- Troubleshooting Guides:
- Code: 71
- Description: Paper Jam 0
- Causes: The front part of paper is jammed between pickup unit and Feed sensor.
- Troubleshooting Guides:
- Code: 72
- Description: Paper Jam 1
- Causes: The front part of paper is jammed between the Discharge sensor and Feed sensor.
- Troubleshooting Guides:
- Code: 73
- Description: Paper Jam 2
- Causes: The front part of paper is jammed just after passing through the discharge sensor.
- Troubleshooting Guides:
- Code: 95
- Description: LSU Not Ready
- Causes: LSU Scanner Motor not ready or Hsync signal not output.
- Troubleshooting Guides: Replace LSU. If you cannot solve the problem after you replace LSU, replace the main board.
Solve Xerox Phaser 3115 Error codes
– Get more error code list with quick guide to fix printer product, click here
– About get help with reseting Epson inkpad or others, click here
– Get more information about Epson XP 15000 troubleshooting, click here
Xerox printer reset software introduction:
Notes before resetting Xerox printer:
– Identify accurate version, serial and crum of Xerox printer.
– How to get Xerox printer model info: Click Here
– Before you continue with the reprogramming of the firmware, please make sure that the device is installed on your computer.
– It is very important that under no circumstances should you remove the chip from the cartridge while reprogramming the firmware. After you have succesfully reprogrammed the printer, remove the chip from the cartridge and store it somewhere safely (the chip – a key). In all cartridges which you are going to use in the printer, the chip has to be either removed or sealed. If you have accidently inserted a new cartridge without removing the chip, the device will be blocked. In order to unblock it, you can use the stored chip as a key which help you to unblock the printer.
– And make sure that any other devices (except mouse and keyboard), which are connected to your computer via USB or LPT ports are disconnected. It’s preferable that the computer is connected to the “UPS” (uninterruptible power source) device, because if during the reprogramming process the electricity source has any interruptions, then the reprogramming will be carried out with an error, which makes the device unable to work.
– This firmware will be installed directly to your printer. Before opening firmare link make sure that printer is turned on and connected to your computer and printer drivers are installed correctly.
Be aware that with the reprogramming of the firmware the manufacturer’s warranty goes lost!!
How To Run Firmware Fix Xerox printer
1. Connect the printer to the computer and turn it on.
2. Wait until the printer is ready for work.
3. Drag and drop *.hd to usbprns2.exe file.
4. The reprogramming process starts automatically.
5. Wait until the printer reprograms (10-20 minute) and restarts.
6. After that the reprogramming process is finished, restart the printer.
– Fix Xerox B205 Toner Empty Error, click here
Contact us to get support with Xerox Phaser 3115 Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
Or click here to get more ways.
