Xerox 5332 error and solving error codes
– Compatible Printer model: Xerox 5332
– Xerox 5332 Error Codes with quick guides:
- Code: A1
- Description: Document in ADF
- Code: A1-8
- Description: Main board received reset signal
- Code: A2
- Description: ADF jams
- Code: A6
- Description: ADF registration jam
- Code: A7
- Description: ADF interlock
- Code: A9
- Description: Tray 1 jam
- Code: C1
- Description: Tray 2 jam
- Code: C2
- Description: Tray 3 jam
- Code: C3
- Description: Bypass feed jams
- Code: C4
- Description: Machine has reset
- Code: E1
- Description: Jam
- Code: E1 … E1-0
- Description: Registration jam
Solve Xerox 5332 Error codes
- Code: E1-5
- Description: Clamshell interlock
- Code: E1-6
- Description: Right side interlock
- Code: E1-7
- Description: Two tray interlock, or duplex interlock
- Code: E1-8
- Description: Sorter interlock
- Code: E1-9
- Description: Copy cartridge interlock
- Code: E2
- Description: Reset signal happened
- Code: E3
- Description: Jam in transfer area
- Code: E4
- Description: Exit jam
- Code: E4-0
- Description: Exit jam
- Code: E4-5
- Description: Clamshell interlock
- Code: E4-6
- Description: Right side interlock
- Code: E4-7
- Description: Two tray interlock
- Code: E4-8
- Description: Sorter interlock
- Code: E4-9
- Description: Copy cartridge interlock
- Code: E5
- Description: Clamshell interlock
- Code: E6
- Description: Right side interlock
- Code: E9
- Description: Copy cartridge interlock
- Code: F3-1
- Description: Sorter bin home switch
- Code: F3-2
- Description: Sorter cam switch
- Code: F3-3
- Description: Sorter cam switch
- Code: F5
- Description: Sorter interlock
- Code: J1-1
- Description: Add toner
- Code: J1-2
- Description: Temporary low toner signal
- Code: J2-1, J2-2
- Description: Replace copy cartridge
- Code: J5, J6
- Description: ADF to machine communications problem
- Code: L2
- Description: 2000 copies left on cartridge
- Code: L3
- Description: ADF to machine communications problem
- Code: L4
- Description: (flashing) 1000 copier left on fuser web
- Code: L6
- Description: Auditron or other counter problem
- Code: LL
- Description: Main board. Try simulation 1.1 to initialize
- Code: rc
- Description: Wrong operation panel installed
- Code: rr
- Description: Bad EPROM on main board. Try 1.1
- Code: U0
- Description: Main board
- Code: U2
- Description: Scan problem
- Code: U2-1
- Description: Scan home
- Code: U2-2
- Description: Scan home or scan encoder
- Code: U2-4
- Description: Scan home or scan dual page sensor
- Code: U2-7
- Description: Scan home
- Code: U4-1
- Description: Fuser problem. Long warm up
- Code: U4-2
- Description: Low fuser temperature after warm up
- Code: U4-3
- Description: High fuser temperature
- Code: U4-4
- Description: Open fuser thermistor
- Code: U4-6
- Description: Replace fuser web.
- Code: U4-7
- Description: Thermistor signal problem
- Code: U7-1
- Description: Copy cartridge belt drive problem
- Code: U9-3
- Description: Exposure lamp problem
- Code: U9-4
- Description: Toner motor
- Code: U9-5
- Description: Problem in warm-up.
– Get more error code list with quick guide to fix printer product, click here
– About get help with reseting Epson inkpad or others, click here
– Get more information about Epson XP 15000 troubleshooting, click here
Xerox printer reset software introduction:
Notes before resetting Xerox printer:
– Identify accurate version, serial and crum of Xerox printer.
– How to get Xerox printer model info: Click Here
– Before you continue with the reprogramming of the firmware, please make sure that the device is installed on your computer.
– It is very important that under no circumstances should you remove the chip from the cartridge while reprogramming the firmware. After you have succesfully reprogrammed the printer, remove the chip from the cartridge and store it somewhere safely (the chip – a key). In all cartridges which you are going to use in the printer, the chip has to be either removed or sealed. If you have accidently inserted a new cartridge without removing the chip, the device will be blocked. In order to unblock it, you can use the stored chip as a key which help you to unblock the printer.
– And make sure that any other devices (except mouse and keyboard), which are connected to your computer via USB or LPT ports are disconnected. It’s preferable that the computer is connected to the “UPS” (uninterruptible power source) device, because if during the reprogramming process the electricity source has any interruptions, then the reprogramming will be carried out with an error, which makes the device unable to work.
– This firmware will be installed directly to your printer. Before opening firmare link make sure that printer is turned on and connected to your computer and printer drivers are installed correctly.
Be aware that with the reprogramming of the firmware the manufacturer’s warranty goes lost!!
How To Run Firmware Fix Xerox printer
1. Connect the printer to the computer and turn it on.
2. Wait until the printer is ready for work.
3. Drag and drop *.hd to usbprns2.exe file.
4. The reprogramming process starts automatically.
5. Wait until the printer reprograms (10-20 minute) and restarts.
6. After that the reprogramming process is finished, restart the printer.
– Fix Xerox B205 Toner Empty Error, click here
Contact us to get support with Xerox 5332 Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
Or click here to get more ways.
