Xerox 5318 error and solving error codes
– Compatible Printer model: Xerox 5318
– Xerox 5318 Error Codes with quick guides:
- Code: A1-1 … A1-32
- Description: All indicate a paper path problem, etc. in the ADF.
- Code: A1-11
- Description: Original ready switch
- Code: A1-12
- Description: Feed sensor
- Code: A1-21
- Description: Original ready switch and document registration sensor or both the document feed sensor and document registration sensor
- Code: A1-22
- Description: ADF registration sensor
- Code: A1-23
- Description: Original did not reach ADF registration sensor quickly enough
- Code: A1-24
- Description: ADF sensor stuck down too long
- Code: A1-25
- Description: ADF sensor actuated at the wrong time during single sheet feed
- Code: A1-26
- Description: ADF sensor not actuated quickly enough in sheet feed mode
- Code: A1-31
- Description: In reverse, ADF sensor is not actuated soon enough
- Code: A1-32
- Description: In reverse, ADF sensor is actuated too long
- Code: A2
- Description: ADF exit problems
Solve Xerox 5318 Error codes
- Code: A2-1
- Description: Original ready sensor and ADF exit switch are actuated or ADF feed in sensor and ADF exit switch are both actuated
- Code: A2-2
- Description: ADF exit switch
- Code: A2-3
- Description: ADF exit switch is not actuated on time
- Code: A3
- Description: Irregular size documents
- Code: A3-1
- Description: Wrong size original sensed in 1 to 1 mode
- Code: A3-2
- Description: Wrong size original sensed in the 2:1 mode
- Code: A5
- Description: ADF interlock
- Code: A5
- Description: ADF interlock
- Code: A6
- Description: ADF single sheet document reset.
- Code: A6-1
- Description: Reset original
- Code: A6-2
- Description: Reset sheet feeder
- Code: A7
- Description: Platen interlock
- Code: A7
- Description: Document cover interlock
- Code: A8
- Description: ADF exit interlock
- Code: A8
- Description: ADF interlock at exit end
- Code: C1
- Description: Tray 1 jam
- Code: C1-2
- Description: Paper feed problem in tray 1
- Code: C1-3
- Description: Paper does not reach registration
- Code: C2
- Description: Tray 2 jam
- Code: C3
- Description: Tray 3 jam
- Code: C3-1
- Description: Paper feed problem from tray 3
- Code: C3-2
- Description: Paper feed problem from tray 3
- Code: C3-3
- Description: Paper feed problem from tray 1
- Code: C6-1
- Description: Duplex paper feed problem
- Code: C6-1,-2
- Description: Jams related to duplex
- Code: C6-2
- Description: Duplex and/or tray 1 paper feed problem
- Code: C6-3
- Description: Paper feed problem from tray 1
- Code: C6-3
- Description: Registration sensor, re tray 1
- Code: C7-1
- Description: Paper feed problem from HCF
- Code: C7-1,-2
- Description: HCF feed problems
- Code: C7-2
- Description: Paper feed problem from HCF on tray 1
- Code: C7-3
- Description: Paper feed problem from tray 1
- Code: C7-3
- Description: Tray 1 feed problem
- Code: C8
- Description: Paper stays in tray or duplex or HCF
- Code: C8-1
- Description: Paper on tray 1 feed sensor
- Code: C8-2
- Description: Paper on tray 2 feed sensor
- Code: C8-3
- Description: Paper on tray 3 feed sensor
- Code: C8-4
- Description: Paper on HCF feed sensor
- Code: C8-5
- Description: Paper in duplex section
- Code: C9
- Description: Bypass feed problem
- Code: C9-3
- Description: Paper from bypass did not reach registration sensor quickly enough
- Code: E1-10 … E-15
- Description: Paper did not reach exit switch
- Code: E1-10 … E1-25
- Description: Internal jam
- Code: E1-20 … E-25
- Description: Paper stayed on registration sensor too long
- Code: E1-6
- Description: Paper on registration sensor
- Code: E1-6
- Description: Paper on registration sensor
- Code: E2
- Description: Reset signal happened. Might read E-2 something else.
- Code: E3-30 … E3-35
- Description: Exit switch actuated too long
- Code: E3-30 … E4-14
- Description: Exit jam
- Code: E3-6
- Description: Exit jam
- Code: E3-6
- Description: Paper on exit switch
- Code: E4-10 … E4-14
- Description: Inverter sensor not actuated.
- Code: E4-10 … E4-45
- Description: Paper did not reach inverter switch soon enough
- Code: E4-15
- Description: Inverter sensor
- Code: E4-40, E4-41, E4-12 ,E4-43, E4-44, E4-45
- Description: Duplex entry sensor
- Code: E4-6
- Description: Paper on inverter switch
- Code: E4-6
- Description: Inverter sensor
- Code: E5
- Description: Front door interlock
- Code: E5
- Description: Front door interlock
- Code: E6-1
- Description: Tray 1 interlock
- Code: E6-1
- Description: Tray 1 interlock
- Code: E6-2
- Description: Tray 1 or duplex interlock
- Code: E6-2
- Description: 2 tray or duplex interlock
- Code: E6-3
- Description: HCF interlock
- Code: E6-3
- Description: HCF interlock
- Code: E7-2
- Description: Duplex inverter interlock
- Code: E7-2,-3
- Description: Duplex interlock
- Code: E7-3
- Description: Duplex interlock
- Code: E8-10 … E8-15
- Description: Paper on duplex feed sensor is not actuated soon enough
- Code: E8-6
- Description: Paper in duplex
- Code: E8-6 … E8-15
- Description: Duplex entry sensor
- Code: F1-1
- Description: Paper did not reach sorter
- Code: F1-1
- Description: Sorter entry sensor
- Code: F1-2
- Description: Paper stayed on sorter feed sensor
- Code: F1-6
- Description: Sorter exit sensor
- Code: F1-6
- Description: Paper on sorter exit sensor
- Code: F3
- Description: Paper size can not stack or sort
- Code: F3
- Description: Paper size not available for sort/stack
- Code: F5
- Description: Sorter interlock
- Code: F5
- Description: Sorter interlock
- Code: H2-1
- Description: Communication problem between main board and duplex board
- Code: H2-2
- Description: Side guard sensor problem
- Code: H3-1
- Description: Communication problem between main board and HCF
- Code: H3-2
- Description: Upper limit sensor problem on HCF
- Code: H6-1
- Description: ADF size sensor
- Code: H6-2
- Description: ADF nudgeer sensor
- Code: H6-3
- Description: Belt drive motor does not have 24 volts. Black toner is empty, but 100 copies have been run without changing toner
- Code: J1
- Description: Add toner
- Code: J1
- Description: Black toner is empty, but 100 copies have been run without changing toner
- Code: J3
- Description: Replace copy cartridge
- Code: J3
- Description: No copy cartridge (drum unit)
- Code: J7
- Description: Replace copy cartridge
- Code: J7
- Description: Copy cartrige must be replaced
- Code: J8-1
- Description: Wrong copy cartridge installed
- Code: J8-1
- Description: Wrong copy cartridge installed
- Code: J8-2
- Description: Copy cartridge EEPROM
- Code: J8-2
- Description: Copy cartridge EEPROM must be changed
- Code: L6
- Description: Auditron or other counter problem
- Code: L6
- Description: Key counter not installed
- Code: L8
- Description: Platen glass temperature is too high
- Code: L8
- Description: Platen glass too hot
- Code: L9
- Description: Communication problem between inter image and main board
- Code: L9
- Description: Communication problem between interimage erase/edge lamps and main board
- Code: U1-1
- Description: Main motor drive problem
- Code: U1-1
- Description: Drive problem
- Code: U2-1
- Description: Scan home problem
- Code: U2-1, U2–2, U2–3, U2–4
- Description: Scan home sensor
- Code: U2-2
- Description: Scan home problem or optics problem
- Code: U2-3
- Description: Scan home problem
- Code: U2-4
- Description: Scan home problem
- Code: U3-1
- Description: Lens sensor problem
- Code: U3-1
- Description: Lens sensor
- Code: U4-1
- Description: Fuser thermistor open
- Code: U4-1
- Description: Open fuser thermistor
- Code: U4-2
- Description: Fuser did not warm up properly
- Code: U4-2
- Description: Low fuser temperature
- Code: U4-3
- Description: Fuser temperature too high
- Code: U4-3
- Description: High fuser temperature
- Code: U4-4
- Description: Fuser problem. Staying on too long
- Code: U4-4
- Description: High fuser temperature
- Code: U4-6
- Description: High fuser temperature
- Code: U4-6
- Description: High fuser temperature
- Code: U5-1
- Description: Sorter bin home switch not activated
- Code: U5-1 … U5-4
- Description: Sorter bin home problem
- Code: U5-2
- Description: Sorter bin home switch stayed actuated
- Code: U5-3
- Description: Sorter bin home switch
- Code: U5-4
- Description: Sorter bin home switch
- Code: U6-1
- Description: ROM problem
- Code: U6-1
- Description: ROM problem
- Code: U6-2
- Description: RAM problem
- Code: U6-2
- Description: RAM problem
- Code: U6-3
- Description: Battery
- Code: U6-3
- Description: Low battery
- Code: U6-4
- Description: NVM problem. Reinitialize.
- Code: U6-4
- Description: Incorrect value in NVM. Reinitialize main board with code 20-96
- Code: U8-1
- Description: Exposure lamp problem
- Code: U8-1, U8-2, U8–3, U8–4, U8–5, U8–6
- Description: Problem with exposure lamp, lamp sensor, lamp board
- Code: U8-2
- Description: Communication problem main board and exposure board
- Code: U8-3
- Description: Exposure lamp or exposure lamp board problem
– Get more error code list with quick guide to fix printer product, click here
– About get help with reseting Epson inkpad or others, click here
– Get more information about Epson XP 15000 troubleshooting, click here
Xerox printer reset software introduction:
Notes before resetting Xerox printer:
– Identify accurate version, serial and crum of Xerox printer.
– How to get Xerox printer model info: Click Here
– Before you continue with the reprogramming of the firmware, please make sure that the device is installed on your computer.
– It is very important that under no circumstances should you remove the chip from the cartridge while reprogramming the firmware. After you have succesfully reprogrammed the printer, remove the chip from the cartridge and store it somewhere safely (the chip – a key). In all cartridges which you are going to use in the printer, the chip has to be either removed or sealed. If you have accidently inserted a new cartridge without removing the chip, the device will be blocked. In order to unblock it, you can use the stored chip as a key which help you to unblock the printer.
– And make sure that any other devices (except mouse and keyboard), which are connected to your computer via USB or LPT ports are disconnected. It’s preferable that the computer is connected to the “UPS” (uninterruptible power source) device, because if during the reprogramming process the electricity source has any interruptions, then the reprogramming will be carried out with an error, which makes the device unable to work.
– This firmware will be installed directly to your printer. Before opening firmare link make sure that printer is turned on and connected to your computer and printer drivers are installed correctly.
Be aware that with the reprogramming of the firmware the manufacturer’s warranty goes lost!!
How To Run Firmware Fix Xerox printer
1. Connect the printer to the computer and turn it on.
2. Wait until the printer is ready for work.
3. Drag and drop *.hd to usbprns2.exe file.
4. The reprogramming process starts automatically.
5. Wait until the printer reprograms (10-20 minute) and restarts.
6. After that the reprogramming process is finished, restart the printer.
– Fix Xerox B205 Toner Empty Error, click here
Contact us to get support with Xerox 5318 Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
Or click here to get more ways.
