Samsung ML2525W model and fix error codes list
– Compatible Printer model: Samsung ML2525W
– Samsung ML2525W Error Codes with quick guides:
- Code: 00 … 05
- Display: Ready(kind of paper)
- Description: The printer is ready, the paper is detected when the first paper is printed. 00: Legal ,01: Letter ,02: A4 ,03: EXEC ,04: B5 ,05: Folio, 06: A5/A6
- Code: 20, 21, 22
- Display: Print Start
- Description: The engine controller received the print order from the video controller. 20: 1st, 21: MP, 22: SCF
- Code: 30
- Display: Feed Sensor On
- Description: The paper is passing out of the Feed Sensor.
- Code: 40
- Display: Feed Sensor off
- Description: The paper has passed out of the Feed Sensor.
- Code: 50
- Display: Paper Out
- Description: The paper has passed out of Exit Sensor.
- Code: 60, 62, 68
- Display: Fuser Error
- Description: The error in the fuser occurred. There is a short circuit in the thermistor and the thermostat while printing, Low Temperature Error occurs. • 60: Open Fuser Error • 62: Low Heat Error • 68: Over Heat Error
- Code: 61
- Display: Warm up
- Description: The printer is on, the cover is open or close.
- Code: 64
- Display: Cover Open
- Description: The Printer Cover is open.
- Code: 65
- Display: CRU Error
- Description: The Toner Cartridge not installed,
- Code: 69
- Display: Sleep Mode
- Description: The fuser power turned off to minimize the power consumption.
- Code: 70
- Display: No Paper
- Description: No paper in the paper cassette.
- Code: 71
- Display: Paper Jam 0
- Description: The front part of paper is jammed between pickup unit and Feed sensor.
Solve Samsung ML2525W Error codes
- Code: 72
- Display: Paper Jam 1
- Description: The front part of paper is jammed between the Discharge sensor and Feed sensor.
- Code: 73
- Display: Paper Jam 2
- Description: The front part of paper is jammed just after passing through the discharge sensor.
- Code: 76
- Display: Out Bin Full
- Description: The Out bin is filled with paper.
- Code: 95
- Display: LSU Not Ready
- Description: LSU Scanner Motor not ready or Hsync signal not output.
– Get more information about Epson XP 15000 troubleshooting, click here
– Get more error code list with quick guide to fix printer product, click here
– About get help with reseting Epson inkpad or others, click here
Samsung printer reset software introduction:
Notes before resetting Samsung printer:
– Identify accurate version, serial and crum of Samsung printer.
– How to get Samsung printer model info: Click Here
– Before you continue with the reprogramming of the firmware, please make sure that the device is installed on your computer.
– It is very important that under no circumstances should you remove the chip from the cartridge while reprogramming the firmware. After you have succesfully reprogrammed the printer, remove the chip from the cartridge and store it somewhere safely (the chip – a key). In all cartridges which you are going to use in the printer, the chip has to be either removed or sealed. If you have accidently inserted a new cartridge without removing the chip, the device will be blocked. In order to unblock it, you can use the stored chip as a key which help you to unblock the printer.
– And make sure that any other devices (except mouse and keyboard), which are connected to your computer via USB or LPT ports are disconnected. It’s preferable that the computer is connected to the “UPS” (uninterruptible power source) device, because if during the reprogramming process the electricity source has any interruptions, then the reprogramming will be carried out with an error, which makes the device unable to work.
– This firmware will be installed directly to your printer. Before opening firmare link make sure that printer is turned on and connected to your computer and printer drivers are installed correctly.
Be aware that with the reprogramming of the firmware the manufacturer’s warranty goes lost!!
How To Run Firmware Fix Samsung printer
1. Connect the printer to the computer and turn it on.
2. Wait until the printer is ready for work.
3. Drag and drop *.hd to usbprns2.exe file.
4. The reprogramming process starts automatically.
5. Wait until the printer reprograms (10-20 minute) and restarts.
6. After that the reprogramming process is finished, restart the printer.
Contact us to get support with Samsung ML2525W Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
Or click here to get more ways.
