Samsung CLX3160FN model and fix error codes list

Samsung CLX3160FN model and fix error codes list

– Compatible Printer model: Samsung CLX3160FN
– Samsung CLX3160FN Error Codes with quick guides:

• Code: 01
• Display: [Color] Toner Empty
• Description: The color toner cartridge has run out. The machine stops printing.
• Troubleshooting Guides: Replace the color toner cartridge with a new one.

• Code: 02
• Display: [Color] Toner Low
• Description: The corresponding color toner cartridge is almost empty.
• Troubleshooting Guides: Take out the toner cartridge and thoroughly shake it. By doing this, you can tem porarily reestablish printing operations.

• Code: 03
• Display: [COMM. Error]
• Description: The machine has a communication problem.
• Troubleshooting Guides: Ask the sender to try again.

• Code: 04
• Display: [Incompatible]
• Description: The remote machine does not have the requested feature, such as polling. This message also occurs if the remote machine does not have enough memory space to complete the operation you are attempting.
• Troubleshooting Guides: Reconfirm the remote machine’s features.

• Code: 05
• Display: [Line Error]
• Description: Your machine cannot connect with the receiving fax machine or has lost contact because of a problem with the phone line.
• Troubleshooting Guides: Try again. If the problem persists, wait an hour or so for the line to clear and try again. Or, turn the ECM mode on.

• Code: 06
• Display: [No Answer]
• Description: The receiving fax machine has not answered after several redial attempts.
• Troubleshooting Guides: Try again. Make sure that the receiving machine is operational.

• Code: 07
• Display: [No Paper] Add Paper
• Description: The paper in the tray has run out.
• Troubleshooting Guides: Load paper in the tray.

• Code: 08
• Display: [Stop Pressed]
• Description: Stop/Clear has been pressed during an operation.
• Troubleshooting Guides: Try again.

• Code: 09
• Display: ADC Not Confirm Error
• Description: Aproblem has occurred in the ADC in the machine.
• Troubleshooting Guides: Replace to the Main board.

• Code: 10
• Display: Cancel? 1:Yes 2:No
• Description: Your machine’s memory has become full while trying to store an original into memory.
• Troubleshooting Guides: To cancel the fax job, press the 1 button to accept Yes. If you want to send those pages that have been successfully stored, press the 2 button to accept No. You should send the remaining pages later, when memory is available.

• Code: 11
• Display: Deve Home Sensor Error
• Description: There is a problem in the fuser unit.
• Troubleshooting Guides: Unplug the power cord and plug it back in. If the problem persists, Replace to the Main board.

• Code: 12
• Display: Document Jam
• Description: The loaded original has jammed in the ADF.
• Troubleshooting Guides: Clear the jam.

Solve Samsung CLX3160FN Error codes

• Code: 13
• Display: Door Open
• Description: The front cover or rear cover is not securely latched.
• Troubleshooting Guides: Close the cover until it locks into place.

• Code: 14
• Display: Enter Again
• Description: You entered an unavailable item.
• Troubleshooting Guides: Enter the correct item again.

• Code: 15
• Display: Fuser Fan Locked
• Description: There is a problem in the cooling fan of the machine.
• Troubleshooting Guides: Open and then close the front cover.

• Code: 16
• Display: Group Not Available
• Description: You have tried to select a group location number where only a single location number can be used, such as when adding locations for a Multiple Send operation.
• Troubleshooting Guides: Use a speed dial number or dial a number manually using the number keypad.

• Code: 17
• Display: Install [Color] Toner
• Description: The color toner cartridge is not installed.
• Troubleshooting Guides: Install the color toner cartridge.

• Code: 18
• Display: Install [Part]
• Description: The corresponding part of the machine is not installed.
• Troubleshooting Guides: Install the part into your machine.

• Code: 19
• Display: Invalid [Color] Toner
• Description: The color toner cartridge you have installed is not for your machine.
• Troubleshooting Guides: Install the a Samsung-genuine color toner cartridge designed for your machine.

• Code: 20
• Display: Invalid [Part]
• Description: The color part of the machine is not for your machine.
• Troubleshooting Guides: Install the a Samsung-genuine part designed for your machine.

• Code: 21
• Display: Line Busy
• Description: The receiving fax machine did not answer or the line is already engaged.
• Troubleshooting Guides: Try again after a few minutes.

• Code: 22
• Display: Low Heat Error Cycle Power
• Description: There is a problem in the fuser unit.
• Troubleshooting Guides: Unplug the power cord and plug it back in. If the problem persists, Replace to the Toner Cartridge.

• Code: 23
• Display: LSU Hsync Error Cycle Power
• Description: Aproblem has occurred in the LSU (Laser Scanning Unit).
• Troubleshooting Guides: Unplug the power cord and plug it back in. If the problem persists, Replace to the Toner Cartridge.

• Code: 24
• Display: LSU Motor Error Cycle Power
• Description: Aproblem has occurred in the LSU (Laser Scanning Unit).
• Troubleshooting Guides: Unplug the power cord and plug it back in. If the problem persists, Replace to the LSU Unit.

• Code: 25
• Display: Main Motor Locked
• Description: There is a problem in the main motor.
• Troubleshooting Guides: Open and then close the front cover.

• Code: 26
• Display: Memory Dial Full
• Description: You are trying to schedule a fax job when memory for storing fax jobs is full.
• Troubleshooting Guides: Wait until a scheduled job is complete.

• Code: 27
• Display: Memory Full
• Description: The memory is full.
• Troubleshooting Guides: Delete unnecessary fax jobs and retransmit after more memory becomes available. Alternatively, split the transmission into more than one operation.

• Code: 28
• Display: MP Tray Paper Empty
• Description: There is no paper in the multi-purpose tray.
• Troubleshooting Guides: Load paper in the multi-purpose tray.

• Code: 29
• Display: Not Assigned
• Description: The speed button or speed dial number you tried to use has no number assigned to it.
• Troubleshooting Guides: Enter the number manually using the number keypad or store the number or address.

• Code: 30
• Display: Open Heat Error Cycle Power
• Description: There is a problem in the fuser unit.
• Troubleshooting Guides: Unplug the power cord and plug it back in. If the problem persists, Replace to the Fuser Unit.

• Code: 31
• Display: Operation Not Assigned
• Description: You are in the Add Page/Cancel Job operation, but there are no jobs stored.
• Troubleshooting Guides: Check the display to see if there are any scheduled jobs.

• Code: 32
• Display: Out Bin Full
• Description: The output tray of the machine is full of paper
• Troubleshooting Guides: Remove paper.

• Code: 33
• Display: Paper Jam 0 Open/Close Door
• Description: Paper has jammed in the feeding area of the tray.
• Troubleshooting Guides: Clear the jam.

• Code: 34
• Display: Paper Jam 1 Open/Close Door
• Description: Paper has jammed in the paper exit area.
• Troubleshooting Guides: Clear the jam.

• Code: 35
• Display: Power Failure
• Description: Power has turned off then on and the machine’s memory has not been back up.
• Troubleshooting Guides: The job which you were trying to do before the power failure must be completely re-done

• Code: 36
• Display: Replace [Color] Toner
• Description: This message appears between Toner Empty and Toner Low status.
• Troubleshooting Guides: Replace the toner cartridge with a new one.

• Code: 37
• Display: Replace [Part]
• Description: The life of the part expires totally.
• Troubleshooting Guides: Replace the part with a new one. Call for service.

• Code: 38
• Display: Replace [Part] Soon
• Description: The life of the part expires soon.
• Troubleshooting Guides: Replace to maintenance part.

• Code: 39
• Display: Retry Redial?
• Description: The machine is waiting for a specified time interval to redial a previously busy station
• Troubleshooting Guides: You can press OK to immediately redial, or Stop/Clear to cancel the redial operation.

• Code: 40
• Display: Scanner locked
• Description: The scanner module is locked
• Troubleshooting Guides: Unlock the scanner and press Stop/Clear.

• Code: 41
• Display: SCF Cover Open
• Description: The jam cover in the optional tray 2 is open.
• Troubleshooting Guides: Close the jam cover in the optional tray 2.

• Code: 42
• Display: SCF Paper Jam
• Description: Paper has jammed in the optional tray 2.
• Troubleshooting Guides: Clear the jam.

• Code: 43
• Display: Self Diagnostic…
• Description: The engine in your machine is checking some problems detected.
• Troubleshooting Guides: Please wait a few minutes.

• Code: 44
• Display: Transfer Belt Error
• Description: Aproblem has occurred in the transfer belt in the machine.
• Troubleshooting Guides: Unplug the power cord and plug it back in. If the problem persists, please call for service.

• Code: 45
• Display: Tray 1 Paper Empty
• Description: There is no paper in the tray 1.
• Troubleshooting Guides: Load paper in the tray 1.

• Code: 46
• Display: Tray 2 Paper Empty
• Description: There is no paper in the optional tray 2.
• Troubleshooting Guides: Load paper in the optional tray 2.

– Get more information about Epson XP 15000 troubleshooting, click here

– Get more error code list with quick guide to fix printer product, click here

– About get help with reseting Epson inkpad or others, click here

Samsung printer reset software introduction:

Notes before resetting Samsung printer:

– Identify accurate version, serial and crum of Samsung printer.
– How to get Samsung printer model info: Click Here
– Before you continue with the reprogramming of the firmware, please make sure that the device is installed on your computer.
– It is very important that under no circumstances should you remove the chip from the cartridge while reprogramming the firmware. After you have succesfully reprogrammed the printer, remove the chip from the cartridge and store it somewhere safely (the chip – a key). In all cartridges which you are going to use in the printer, the chip has to be either removed or sealed. If you have accidently inserted a new cartridge without removing the chip, the device will be blocked. In order to unblock it, you can use the stored chip as a key which help you to unblock the printer.
– And make sure that any other devices (except mouse and keyboard), which are connected to your computer via USB or LPT ports are disconnected. It’s preferable that the computer is connected to the “UPS” (uninterruptible power source) device, because if during the reprogramming process the electricity source has any interruptions, then the reprogramming will be carried out with an error, which makes the device unable to work.
– This firmware will be installed directly to your printer. Before opening firmare link make sure that printer is turned on and connected to your computer and printer drivers are installed correctly.
Be aware that with the reprogramming of the firmware the manufacturer’s warranty goes lost!!

How To Run Firmware Fix Samsung printer

1. Connect the printer to the computer and turn it on.
2. Wait until the printer is ready for work.
3. Drag and drop *.hd to usbprns2.exe file.

4. The reprogramming process starts automatically.
5. Wait until the printer reprograms (10-20 minute) and restarts.
6. After that the reprogramming process is finished, restart the printer.

Contact us to get support with Samsung CLX3160FN Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
Or click here to get more ways.