Repair Canon PC720 Printer Error Codes Canon Servie Tool
– Printer model: Canon PC720
– Error codes on Canon PC720 model and its description:
– Canon PC720 printer Error Codes and quick guide to troubleshooting:
- Code: C
- Description: No problem. Means that the machine is correcting the fuser film tracking.
- Code: CC
- Description: Drum must be changed. Could be the drum serial number is identified by the logic as being non-compatible to that particular copier.
- Code: E0
- Description: Fuser problem
- Code: E000
- Description: Low fuser temperature
- Code: E001
- Description: High fuser temperature
- Code: E002
- Description: High fuser temperature
- Code: E003
- Description: Erratic fuser temperature
- Code: E007
- Description: Fuser film off track and will not repair itself
- Code: E010
- Description: Main drive problem
- Code: E030
- Description: Counter problem
- Code: E064
- Description: Scan problem, or power supply
- Code: E202
- Description: Scan problem
- Code: E210
- Description: Lens drive problem or lens sensor
- Code: E220
- Description: Exposure lamp stays on or off
- Code: E240
- Description: DC controller (main board) or composite power supply
- Code: E261
- Description: Zero cross problem. Power frequency or composite power supply
- Code: E400
- Description: Communication problem between boards
- Code: E803
- Description: 24 volt problem
- Code: H
- Description: Fuser overheat
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-ip6310d-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-wf-3540-driver-firmware-and-manuals/
Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html
Contact us to get support with Canon PC720 Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
