Repair Canon NP8580 Printer Error Codes Canon Servie Tool
– Printer model: Canon NP8580
– Error codes on Canon NP8580 model and its description:
– Canon NP8580 printer Error Codes and quick guide to troubleshooting:
- Code: E000
- Description: The temperature of the upper fixing roller has not increased above the specified level 90 seconds after switching power on. The temperature of the upper fixing roller does not reach 150 C within 8 minutes after switching power ON. The temperature of the upper fixing roller does not reach 180 C within 5 minutes of reaching 150 C. The temperature of the upper fixing roller drops below 50 C during STANDBY.
- Code: E001
- Description: The temperature of the upper fixing roller exceeds 250 C.
- Code: E005
- Description: The length of fixing assembly cleaning belt wound on the take-up reel exceeds the specified length.
- Code: E010
- Description: When two or more clock pulses are not inputted for a period of 2 seconds after a MAIN MOTOR DRIVE command is generated.
- Code: E011
- Description: When excessive current is detected by the fault detection circuit of the DC driver PCB. When excessive current is detected by the fault detection circuit of the duplexing unit driver PCB. When excessive current is detected by the fault detection circuit of the scanner motor driver PCB.
- Code: E020
- Description: When a toner out signal (TSP) is emitted from the developing assembly for a total of at least two minutes.
- Code: E050
- Description: When the HOLDING TRAY HOME POSITION signal (THP) is not generated within 4 seconds from the beginning of HOLDING TRAY MOTOR DRIVE command (TMDP1,2) When the HOLDING TRAY HOME POSITION signal (THP) is generated for at least one second while the HOLDING TRAY MOTOR DRIVE command (TMDSP1,2) is being generated.
- Code: E203
- Description: When two or more clock pulses are not inputted from the SCANNER MOTOR DRIVE command is being generated.
- Code: E210
- Description: When the LENS HOME POSITION signal (LHP) is not generated within 4.8 seconds after the power switch or door switch goes ON. When the LENS HOME POSITION signal (LHP) is generated for 2 seconds or more.
- Code: E243
- Description: When an abnormally in communication occurs between the microprocessors on the DC controller PCB and those on the control panel PCB.
- Code: E400
- Description: When an abnormality in communication occurs between the DC controller PCB detect RDF controller PCB.
- Code: E401
- Description: When a flag mounted on the pick-up roller HOME position sensor (S3), it indicates that M1 is turning. S3 should go ON and OFF two or more times in one second.
- Code: E402
- Description: The number of pulses in a 200 ms period is too low.
- Code: E403
- Description: When the number of feed motor clock pulses in a 200 ms period is less than the correct value.
- Code: E411
- Description: When the sensor output is greater than 2.3V when there is paper.
- Code: E500
- Description: When an abnormality in communication occurs between the DC controller PCB of sorter detect main controller PCB.
- Code: E510
- Description: When there is no pulse output from the feed roller motor and when the first copy jams.
- Code: E540
- Description: The lead can HOME position sensor does not go ‘OFF’ within 0.5 second after the BIN MOTOR DRIVE signal (BMON) is output.
- Code: E541
- Description: The lead can HOME position sensor does not go ‘ON’ within 1.0 second after the lead cam position sensor goes ‘OFF’.
- Code: E710
- Description: When an abnormality in communication occurs between the DC controller PCB and the RF controller PCB or sorter controller PCB detect DC controller PCB.
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-ip2700-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-wp-4533-driver-firmware-and-manuals/
Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html
Contact us to get support with Canon NP8580 Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
