Repair Canon NP3325 Printer Error Codes Canon Servie Tool
– Printer model: Canon NP3325
– Error codes on Canon NP3325 model and its description:
– Canon NP3325 printer Error Codes and quick guide to troubleshooting:
- Code: E000
- Description: Low fuser temperature. Heat lamp, thermoswitch, thermofuse, thermistor, SSR
- Code: E001
- Description: High fuser temperature. Thermistor, SSR, pinched wire
- Code: E002
- Description: Low fuser temperature. Same as E002
- Code: E003
- Description: Same as E000/E001
- Code: E010
- Description: Same as E002
- Code: E022
- Description: Motor drive problem
- Code: E030
- Description: Counter
- Code: E202
- Description: Scan motor, sensor
- Code: E204
- Description: Scan motor, sensor
- Code: E210
- Description: Lens motor, sensor
- Code: E220
- Description: Exposure lamp
- Code: E240
- Description: DC controller (main board)
- Code: E401
- Description: Pickup drive problem (might be Doc. Feeder)
- Code: E402
- Description: Document belt drive problem
- Code: E404
- Description: Exit motor (document feeder)
- Code: E411
- Description: Document sensor (document feeder)
- Code: E500
- Description: Sorter/machine communication problem
- Code: E510
- Description: Sorter drive problem
- Code: E530
- Description: Sorter home sensor
- Code: E531
- Description: Stapler unit swing sensor
- Code: E540
- Description: Sorter cam sensor
- Code: E541
- Description: Sorter cam sensor
- Code: E710
- Description: DC controller (main board)
- Code: E712
- Description: DC controller or document feeder board
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-mb2020-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-wf-3820-driver-firmware-and-manuals/
Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html
Contact us to get support with Canon NP3325 Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
