Repair Canon MF8180c Printer Error Codes Canon Servie Tool
– Printer model: Canon MF8180c
– Error codes on Canon MF8180c model and its description:
– Canon MF8180c printer Error Codes and quick guide to troubleshooting:
- Code: E000
- Description: Fixing assembly faulty start-up (open circuit in the main thermistor). fixing assembly faulty start-up (open circuit in the sub thermistor). fixing assembly faulty start-up (open circuit in the fixing heater)
- Solutions: Check the connector of the fixing film unit. Replace the fixing film unit. Replace the DCNT Borad PCB.
- Code: E001
- Description: fixing heater overheating (short-circuit in the main thermistor). fixing heater overheating (short-circuit in the sub thermistor)
- Solutions: Check the connector of the fixing film unit. Replace the fixing film unit. Replace the DCNT Borad.
- Code: E002
- Description: fixing assembly low temperature (open circuit in the main thermistor). fixing assembly low temperature (open circuit in the sub thermistor). fixing assembly low temperature (open circuit in the fixing heater)
- Solutions: Check the connector of the fixing film unit. Replace the fixing film unit. Replace the DCNT Borad.
- Code: E010
- Description: main motor fault
- Solutions: Check the connector of the main motor. Replace the main motor. replace the DCNT Borad.
- Code: E021
- Description: developing rotary motor fault
- Solutions: Check the connector of the developing rotary motor. Replace the developing rotary motor. Replace the DCNT Borad PCB.
- Code: E022
- Description: developing rotary drive mechanism fault
- Solutions: Check the connector of the developing rotary drive sensor. Check the connector of the drive motor. Replace the developing rotary drive sensor. Replace the drive motor. Replace the DC controller PCB.
- Code: E071
- Description: ITB home position sensor fault
- Solutions: Check the connector of the ITB home position sensor. Replace the ITB home position sensor. Replace the DC controller PCB.
- Code: E078
- Description: secondary transfer roller drive mechanism fault
- Solutions: Check the connector of the roller drive sensor. Check the connector of the roller drive clutch. Replace the main drive assembly (roller Drive sensor). Replace the drum cartridge (roller drive cam). Replace the DC controller PCB.
- Code: E100
- Description: scanner fault
- Solutions: Check the connector of the laser scanner assembly. Replace the laser scanner assembly. Replace the DCNT Borad.
- Code: E196
- Description: DCNT Borad memory fault
- Solutions: Replace the DCNT Borad.
- Code: E197
- Description: engine communication error
- Solutions: Replace the DCNT Borad.
- Code: E747
- Description: SCNT board memory fault
- Solutions: Replace the SCNT Borad.
- Code: E805
- Description: fan fault
- Solutions: Check the connector of the cooling fan. Replace the cooling fan. Replace the DCNT Borad.
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-lbp113w-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-stylusrip-driver-firmware-and-manuals/
Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html
Contact us to get support with Canon MF8180c Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
