Repair Canon MF742Cdw Printer Error Codes Canon Servie Tool

– Printer model: Canon MF742Cdw
– Error codes on Canon MF742Cdw model and its description:

– Canon MF742Cdw printer Error Codes and quick guide to troubleshooting:

Code: 0001
Description: Delay jam
Causes: Document End Sensor SR10
Solutions: ADF Pickup Feed Area

Code: 0002
Description: Stationary Jam
Causes: Document End Sensor SR10
Solutions: ADF Pickup Feed Area

Code: 0071
Description: Sequence Jam (Timing Error)
Causes:
Solutions:

Code: 0094
Description: Initial Residual Jam
Causes: Document End Sensor SR10
Solutions: ADF Pickup Feed Area

Code: 0901
Description: Pickup Delay Jam
Causes: Registration Sensor SR1
Solutions: Pickup Cassette of the host machine

Code: 0902
Description: Pickup Delay Jam
Causes: Registration Sensor SR1
Solutions: Multi-purpose Tray

Code: 0903
Description: Pickup Delay Jam
Causes: Registration Sensor SR1
Solutions: Cassette Feeding Module

Code: 0907
Description: Pickup Delay Jam
Causes: Registration Sensor SR1
Solutions: Registration to Drum Area

Code: 0908
Description: Pickup Delay Jam
Causes: Registration Sensor SR1
Solutions: Drum to Fixing Area

Code: 0909
Description: Pickup Delay Jam
Causes: Registration Sensor SR1
Solutions: Fixing to Delivery Area

Code: 090C
Description: Pickup Delay Jam
Causes: Registration Sensor SR1
Solutions: Duplex Reverse Area

Code: 090D
Description: Pickup Delay Jam
Causes: Registration Sensor SR1
Solutions: Duplex Feed Area

Code: 0A01
Description: Pickup Delay Jam
Causes: Cassette Feed Sensor SR31
Solutions: Pickup Cassette of the host machine

Code: 0A03
Description: Pickup Delay Jam
Causes: Cassette Feed Sensor SR31
Solutions: Cassette Feeding Module

Code: 0A07
Description: Pickup Delay Jam
Causes: Cassette Feed Sensor SR31
Solutions: Registration to Drum Area

Code: 0A08
Description: Pickup Delay Jam
Causes: Cassette Feed Sensor SR31
Solutions: Drum to Fixing Area

Code: 0A09
Description: Pickup Delay Jam
Causes: Cassette Feed Sensor SR31
Solutions: Fixing to Delivery Area

Code: 0A0C
Description: Pickup Delay Jam
Causes: Cassette Feed Sensor SR31
Solutions: Duplex Reverse Area

Code: 0A0D
Description: Pickup Delay Jam
Causes: Cassette Feed Sensor SR31
Solutions: Duplex Feed Area

Code: 10-0100
Description: Toner Cartridge replacement notification alarm (K)
Causes: Detail Code: 0071
Solutions: When the replacement with a genuine Toner Cartridge was detected.

Code: 10-0100
Description: Toner Cartridge replacement notification alarm (Y)
Causes: Detail Code: 0072
Solutions: When the replacement with a genuine Toner Cartridge was detected.

Code: 10-0100
Description: Toner Cartridge replacement notification alarm (M)
Causes: Detail Code: 0073
Solutions: When the replacement with a genuine Toner Cartridge was detected.

Code: 10-0100
Description: Toner Cartridge replacement notification alarm (C)
Causes: Detail Code: 0074
Solutions: When the replacement with a genuine Toner Cartridge was detected.

Code: 10-0100
Description: Unidentified Toner Cartridge replacement notification alarm (K)
Causes: Detail Code: 0181
Solutions: When the replacement with a non-genuine Toner Cartridge was detected.

Code: 10-0100
Description: Unidentified Toner Cartridge replacement notification alarm (Y)
Causes: Detail Code: 0182
Solutions: When the replacement with a non-genuine Toner Cartridge was detected.

Code: 10-0100
Description: Unidentified Toner Cartridge replacement notification alarm (M)
Causes: Detail Code: 0183
Solutions: When the replacement with a non-genuine Toner Cartridge was detected.

Code: 10-0100
Description: Unidentified Toner Cartridge replacement notification alarm (C)
Causes: Detail Code: 0184
Solutions: When the replacement with a non-genuine Toner Cartridge was detected.

Code: 10-0401
Description: Toner Cartridge empty alarm (Y)
Causes: Alarm to be generated once the Toner Cartridge becomes empty.
Solutions:

Code: 10-0402
Description: Toner Cartridge empty alarm (M)
Causes: Alarm to be generated once the Toner Cartridge becomes empty.
Solutions:

Code: 10-0403
Description: Toner Cartridge empty alarm (C)
Causes: Alarm to be generated once the Toner Cartridge becomes empty.
Solutions:

Code: 10-0404
Description: Toner Cartridge empty alarm (Bk)
Causes: Alarm to be generated once the Toner Cartridge becomes empty.
Solutions:

Code: 1101
Description: Pickup Stationary Jam
Causes: Registration Sensor SR1
Solutions: Pickup Cassette of the host machine

Code: 1103
Description: Pickup Stationary Jam
Causes: Registration Sensor SR1
Solutions: Cassette Feeding Module

Code: 1107
Description: Pickup Stationary Jam
Causes: Registration Sensor SR1
Solutions: Registration to Drum Area

Code: 1108
Description: Pickup Stationary Jam
Causes: Registration Sensor SR1
Solutions: Drum to Fixing Area

Code: 1109
Description: Pickup Stationary Jam
Causes: Registration Sensor SR1
Solutions: Fixing to Delivery Area

Code: 110C
Description: Pickup Stationary Jam
Causes: Registration Sensor SR1
Solutions: Duplex Reverse Area

Code: 110D
Description: Pickup Stationary Jam
Causes: Registration Sensor SR1
Solutions: Duplex Feed Area

Code: 1901
Description: Fixing Delivery Delay Jam
Causes: Fixing Delivery Sensor SR3
Solutions: Pickup Cassette of the host machine

Code: 1903
Description: Fixing Delivery Delay Jam
Causes: Fixing Delivery Sensor SR3
Solutions: Cassette Feeding Module

Code: 1907
Description: Fixing Delivery Delay Jam
Causes: Fixing Delivery Sensor SR3
Solutions: Registration to Drum Area

Code: 1908
Description: Fixing Delivery Delay Jam
Causes: Fixing Delivery Sensor SR3
Solutions: Drum to Fixing Area

Code: 1909
Description: Fixing Delivery Delay Jam
Causes: Fixing Delivery Sensor SR3
Solutions: Fixing to Delivery Area

Code: 190C
Description: Fixing Delivery Delay Jam
Causes: Fixing Delivery Sensor SR3
Solutions: Duplex Reverse Area

Code: 190D
Description: Fixing Delivery Delay Jam
Causes: Fixing Delivery Sensor SR3
Solutions: Duplex Feed Area

Code: 2101
Description: Fixing Delivery Stationary Jam
Causes: Registration Sensor SR1
Solutions: Pickup Cassette of the host machine

Code: 2103
Description: Fixing Delivery Stationary Jam
Causes: Registration Sensor SR1
Solutions: Cassette Feeding Module

Code: 2107
Description: Fixing Delivery Stationary Jam
Causes: Registration Sensor SR1
Solutions: Registration to Drum Area

Code: 2108
Description: Fixing Delivery Stationary Jam
Causes: Registration Sensor SR1
Solutions: Drum to Fixing Area

Code: 2109
Description: Fixing Delivery Stationary Jam
Causes: Registration Sensor SR1
Solutions: Fixing to Delivery Area

Code: 210C
Description: Fixing Delivery Stationary Jam
Causes: Registration Sensor SR1
Solutions: Duplex Reverse Area

Code: 210D
Description: Fixing Delivery Stationary Jam
Causes: Registration Sensor SR1
Solutions: Duplex Feed Area

Code: 2901
Description: Delivery Delay Jam
Causes: Fixing Delivery Sensor SR3
Solutions: Pickup Cassette of the host machine

Code: 2903
Description: Delivery Delay Jam
Causes: Fixing Delivery Sensor SR3
Solutions: Cassette Feeding Module

Code: 2907
Description: Delivery Delay Jam
Causes: Fixing Delivery Sensor SR3
Solutions: Registration to Drum Area

Code: 2908
Description: Delivery Delay Jam
Causes: Fixing Delivery Sensor SR3
Solutions: Drum to Fixing Area

Code: 2909
Description: Delivery Delay Jam
Causes: Fixing Delivery Sensor SR3
Solutions: Fixing to Delivery Area

Code: 290C
Description: Delivery Delay Jam
Causes: Fixing Delivery Sensor SR3
Solutions: Duplex Reverse Area

Code: 290D
Description: Delivery Delay Jam
Causes: Fixing Delivery Sensor SR3
Solutions: Duplex Feed Area

Code: 3101
Description: Delivery Stationary Jam
Causes: Delivery Sensor SR4
Solutions: Pickup Cassette of the host machine

Code: 3103
Description: Delivery Stationary Jam
Causes: Delivery Sensor SR4
Solutions: Cassette Feeding Module

Code: 3107
Description: Delivery Stationary Jam
Causes: Delivery Sensor SR4
Solutions: Registration to Drum Area

Code: 3108
Description: Delivery Stationary Jam
Causes: Delivery Sensor SR4
Solutions: Drum to Fixing Area

Code: 3109
Description: Delivery Stationary Jam
Causes: Delivery Sensor SR4
Solutions: Fixing to Delivery Area

Code: 310A
Description: Delivery Stationary Jam
Causes: Delivery Sensor SR4
Solutions: Delivery Area Duplex Reverse Area

Code: 310D
Description: Delivery Stationary Jam
Causes: Delivery Sensor SR4
Solutions: Duplex Feed Area

Code: 3901
Description: Reverse Delay Jam
Causes: Duplex Reverse Sensor R21
Solutions: Pickup Cassette of the host machine

Code: 3903
Description: Reverse Delay Jam
Causes: Duplex Reverse Sensor R21
Solutions: Cassette Feeding Module

Code: 3907
Description: Reverse Delay Jam
Causes: Duplex Reverse Sensor R21
Solutions: Registration to Drum Area

Code: 3908
Description: Reverse Delay Jam
Causes: Duplex Reverse Sensor R21
Solutions: Drum to Fixing Area

Code: 3909
Description: Reverse Delay Jam
Causes: Duplex Reverse Sensor R21
Solutions: Fixing to Delivery Area

Code: 390C
Description: Reverse Delay Jam
Causes: Duplex Reverse Sensor R21
Solutions: Duplex Reverse Area

Code: 390D
Description: Reverse Delay Jam
Causes: Duplex Reverse Sensor R21
Solutions: Duplex Feed Area

Code: 4101
Description: Reverse Stationary Jam
Causes: Duplex Reverse Sensor R21
Solutions: Pickup Cassette of the host machine

Code: 4103
Description: Reverse Stationary Jam
Causes: Duplex Reverse Sensor R21
Solutions: Cassette Feeding Module

Code: 4107
Description: Reverse Stationary Jam
Causes: Duplex Reverse Sensor R21
Solutions: Registration to Drum Area

Code: 4108
Description: Reverse Stationary Jam
Causes: Duplex Reverse Sensor R21
Solutions: Drum to Fixing Area

Code: 4109
Description: Reverse Stationary Jam
Causes: Duplex Reverse Sensor R21
Solutions: Fixing to Delivery Area

Code: 410C
Description: Reverse Stationary Jam
Causes: Duplex Reverse Sensor R21
Solutions: Duplex Reverse Area

Code: 410D
Description: Reverse Stationary Jam
Causes: Duplex Reverse Sensor R21
Solutions: Duplex Feed Area

Code: 4901
Description: Duplex Feed Delay Jam
Causes: Duplex Re-pickup Sensor SR22
Solutions: Pickup Cassette of the host machine

Code: 4903
Description: Duplex Feed Delay Jam
Causes: Duplex Re-pickup Sensor SR22
Solutions: Cassette Feeding Module

Code: 4907
Description: Duplex Feed Delay Jam
Causes: Duplex Re-pickup Sensor SR22
Solutions: Registration to Drum Area

Code: 4908
Description: Duplex Feed Delay Jam
Causes: Duplex Re-pickup Sensor SR22
Solutions: Drum to Fixing Area

Code: 4909
Description: Duplex Feed Delay Jam
Causes: Duplex Re-pickup Sensor SR22
Solutions: Fixing to Delivery Area

Code: 490C
Description: Duplex Feed Delay Jam
Causes: Duplex Re-pickup Sensor SR22
Solutions: Duplex Reverse Area

Code: 490D
Description: Duplex Feed Delay Jam
Causes: Duplex Re-pickup Sensor SR22
Solutions: Duplex Feed Area

Code: 5901
Description: Duplex Re-pickup Jam
Causes: Registration Sensor SR1
Solutions: Pickup Cassette of the host machine

Code: 5903
Description: Duplex Re-pickup Jam
Causes: Registration Sensor SR1
Solutions: Cassette Feeding Module

Code: 5907
Description: Duplex Re-pickup Jam
Causes: Registration Sensor SR1
Solutions: Registration to Drum Area

Code: 5908
Description: Duplex Re-pickup Jam
Causes: Registration Sensor SR1
Solutions: Drum to Fixing Area

Code: 5909
Description: Duplex Re-pickup Jam
Causes: Registration Sensor SR1
Solutions: Fixing to Delivery Area

Code: 590C
Description: Duplex Re-pickup Jam
Causes: Registration Sensor SR1
Solutions: Duplex Reverse Area

Code: 590D
Description: Duplex Re-pickup Jam
Causes: Registration Sensor SR1
Solutions: Duplex Feed Area

Code: 590E
Description: Duplex Re-pickup Jam
Causes: Registration Sensor SR1
Solutions: Duplex Pickup Area

Code: 6101
Description: Wrapping Jam
Causes: Fixing Delivery Sensor SR3, Duplex Reverse Sensor SR21
Solutions: Pickup Cassette of the host machine

Code: 6103
Description: Wrapping Jam
Causes: Fixing Delivery Sensor SR3, Duplex Reverse Sensor SR21
Solutions: Cassette Feeding Module

Code: 6107
Description: Wrapping Jam
Causes: Fixing Delivery Sensor SR3, Duplex Reverse Sensor SR21
Solutions: Registration to Drum Area

Code: 6108
Description: Wrapping Jam
Causes: Fixing Delivery Sensor SR3, Duplex Reverse Sensor SR21
Solutions: Drum to Fixing Area

Code: 6109
Description: Wrapping Jam
Causes: Fixing Delivery Sensor SR3, Duplex Reverse Sensor SR21
Solutions: Fixing to Delivery Area

Code: 610C
Description: Wrapping Jam
Causes: Fixing Delivery Sensor SR3, Duplex Reverse Sensor SR21
Solutions: Duplex Reverse Area

Code: 610D
Description: Wrapping Jam
Causes: Fixing Delivery Sensor SR3, Duplex Reverse Sensor SR21
Solutions: Duplex Feed Area

Code: 6201
Description: Wrapping Jam
Causes: Fixing Delivery Sensor SR3, Duplex Reverse Sensor SR21
Solutions: Pickup Cassette of the host machine

Code: 6203
Description: Wrapping Jam
Causes: Fixing Delivery Sensor SR3, Duplex Reverse Sensor SR21
Solutions: Cassette Feeding Module

Code: 6207
Description: Wrapping Jam
Causes: Fixing Delivery Sensor SR3, Duplex Reverse Sensor SR21
Solutions: Registration to Drum Area

Code: 6208
Description: Wrapping Jam
Causes: Fixing Delivery Sensor SR3, Duplex Reverse Sensor SR21
Solutions: Drum to Fixing Area

Code: 6209
Description: Wrapping Jam
Causes: Fixing Delivery Sensor SR3, Duplex Reverse Sensor SR21
Solutions: Fixing to Delivery Area

Code: 620C
Description: Wrapping Jam
Causes: Fixing Delivery Sensor SR3, Duplex Reverse Sensor SR21
Solutions: Duplex Reverse Area

Code: 620D
Description: Wrapping Jam
Causes: Fixing Delivery Sensor SR3, Duplex Reverse Sensor SR21
Solutions: Duplex Feed Area

Code: 7101
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Pickup Cassette of the host machine

Code: 7102
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Multi-purpose Tray

Code: 7103
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Cassette Feeding Module

Code: 7107
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Registration to Drum Area

Code: 7108
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Drum to Fixing Area

Code: 7109
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Fixing to Delivery Area

Code: 710C
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Duplex Reverse Area

Code: 710D
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Duplex Feed Area

Code: 710E
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Duplex Pickup Area

Code: 7201
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Pickup Cassette of the host machine

Code: 7202
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Multi-purpose Tray

Code: 7203
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Cassette Feeding Module

Code: 7207
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Registration to Drum Area

Code: 7208
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Drum to Fixing Area

Code: 7209
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Fixing to Delivery Area

Code: 720C
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Duplex Reverse Area

Code: 720D
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Duplex Feed Area

Code: 720E
Description: Internal residual jam
Causes: Registration Sensor Fixing Delivery Sensor Arch Sensor SR1 SR3 SR2
Solutions: Duplex Pickup Area

Code: 7901
Description: Door Open Jam
Causes: Registration Sensor Multi-purpose Tray Paper Sensor Fixing Delivery Sensor Delivery Sensor Duplex Re-pickup Sensor SR1 SR6 SR3 SR4 SR22
Solutions: Pickup Cassette of the host machine

Code: 7902
Description: Door Open Jam
Causes: Registration Sensor Multi-purpose Tray Paper Sensor Fixing Delivery Sensor Delivery Sensor Duplex Re-pickup Sensor SR1 SR6 SR3 SR4 SR22
Solutions: Multi-purpose Tray

Code: 7903
Description: Door Open Jam
Causes: Registration Sensor Multi-purpose Tray Paper Sensor Fixing Delivery Sensor Delivery Sensor Duplex Re-pickup Sensor SR1 SR6 SR3 SR4 SR22
Solutions: Cassette Feeding Module

Code: 7907
Description: Door Open Jam
Causes: Registration Sensor Multi-purpose Tray Paper Sensor Fixing Delivery Sensor Delivery Sensor Duplex Re-pickup Sensor SR1 SR6 SR3 SR4 SR22
Solutions: Registration to Drum Area

Code: 7908
Description: Door Open Jam
Causes: Registration Sensor Multi-purpose Tray Paper Sensor Fixing Delivery Sensor Delivery Sensor Duplex Re-pickup Sensor SR1 SR6 SR3 SR4 SR22
Solutions: Drum to Fixing Area

Code: 7909
Description: Door Open Jam
Causes: Registration Sensor Multi-purpose Tray Paper Sensor Fixing Delivery Sensor Delivery Sensor Duplex Re-pickup Sensor SR1 SR6 SR3 SR4 SR22
Solutions: Fixing to Delivery Area

Code: 790C
Description: Door Open Jam
Causes: Registration Sensor Multi-purpose Tray Paper Sensor Fixing Delivery Sensor Delivery Sensor Duplex Re-pickup Sensor SR1 SR6 SR3 SR4 SR22
Solutions: Duplex Reverse Area

Code: 790D
Description: Door Open Jam
Causes: Registration Sensor Multi-purpose Tray Paper Sensor Fixing Delivery Sensor Delivery Sensor Duplex Re-pickup Sensor SR1 SR6 SR3 SR4 SR22
Solutions: Duplex Feed Area

Code: 790E
Description: Door Open Jam
Causes: Registration Sensor Multi-purpose Tray Paper Sensor Fixing Delivery Sensor Delivery Sensor Duplex Re-pickup Sensor SR1 SR6 SR3 SR4 SR22
Solutions: Duplex Pickup Area

Code: E000-0000
Description: Error in temperature rising of Fixing Assembly
Causes: The temperature of the Fixing Assembly did not reach a certain temperature within the specified time after starting temperature control.
Solutions: 1. Check the harness/connector between the Fixing Assembly and the Engine Controller PCB (UN1). 2. Check the harness/connector between the Fixing Assembly and the Fixing Power Supply PCB (UN3). 3. Check the harness/connector between the Fixing Power Supply PCB (UN3) and the Engine Controller PCB (UN1). 4. Replace the Fixing Assembly. 5. Replace the Fixing Power Supply PCB (UN3). 6. Replace the Low Voltage Power Supply PCB (UN2). 7. Replace the Engine Controller PCB (UN1).

Code: E001-0000
Description: Abnormal high temperature of the Fixing Assembly
Causes: It was detected that the temperature of the Fixing Assembly (Main Thermistor) (TH801) was abnormally high.
Solutions: 1. Check the harness/connector between the Fixing Assembly and the Engine Controller PCB (UN1). 2. Check the harness/connector between the Fixing Assembly and the Fixing Power Supply PCB (UN3). 3. Check the harness/connector between the Fixing Power Supply PCB (UN3) and the Engine Controller PCB (UN1). 4. Replace the Fixing Assembly. 5. Replace the Fixing Power Supply PCB (UN3). 6. Replace the Low Voltage Power Supply PCB (UN2). 7. Replace the Engine Controller PCB (UN1).

Code: E001-0001
Description: Abnormal high temperature of the Fixing Assembly
Causes: It was detected that the temperature of the Fixing Assembly (Sub Thermistor) (TH802/TH803) was abnormally high.
Solutions: 1. Check the harness/connector between the Fixing Assembly and the Engine Controller PCB (UN1). 2. Check the harness/connector between the Fixing Assembly and the Fixing Power Supply PCB (UN3). 3. Check the harness/connector between the Fixing Power Supply PCB (UN3) and the Engine Controller PCB (UN1). 4. Replace the Fixing Assembly. 5. Replace the Fixing Power Supply PCB (UN3). 6. Replace the Low Voltage Power Supply PCB (UN2). 7. Replace the Engine Controller PCB (UN1).

Code: E003-0000
Description: Abnormal low temperature of the Fixing Assembly
Causes: It was detected that the temperature of the Fixing Assembly (main Thermistor) (TH801) was abnormally low.
Solutions: 1. Check the harness/connector between the Fixing Assembly and the Engine Controller PCB (UN1). 2. Check the harness/connector between the Fixing Assembly and the Fixing Power Supply PCB (UN3). 3. Check the harness/connector between the Fixing Power Supply PCB (UN3) and the Engine Controller PCB (UN1). 4. Replace the Fixing Assembly. 5. Replace the Fixing Power Supply PCB (UN3). 6. Replace the Low Voltage Power Supply PCB (UN2). 7. Replace the Engine Controller PCB (UN1).

Code: E003-0001
Description: Abnormal low temperature of the Fixing Assembly
Causes: It was detected that the temperature of the Fixing Assembly (Sub Thermistor) (TH802/TH803) was abnormally low.
Solutions: 1. Check the harness/connector between the Fixing Assembly and the Engine Controller PCB (UN1). 2. Check the harness/connector between the Fixing Assembly and the Fixing Power Supply PCB (UN3). 3. Check the harness/connector between the Fixing Power Supply PCB (UN3) and the Engine Controller PCB (UN1). 4. Replace the Fixing Assembly. 5. Replace the Fixing Power Supply PCB (UN3). 6. Replace the Low Voltage Power Supply PCB (UN2). 7. Replace the Engine Controller PCB (UN1).

Code: E004-0000
Description: Error in fixing power supply drive circuit
Causes: The zero cross signal was not detected for the specified period of time or longer.
Solutions: 1. Check the harness/connector between the Engine Controller PCB (UN1) and the Thermistor (TH801/TH802/TH803). 2. Check the harness/connectors between the Fixing Assembly and the Fixing Power Supply PCB (UN3). 3. Check the harness/connector between the Fixing Power Supply PCB (UN3) and the Engine Controller PCB (UN1). 4. Replace the Fixing Assembly. 5. Replace the Fixing Power Supply PCB (UN3). 6. Replace the Low Voltage Power Supply PCB (UN2). 7. Replace the Engine Controller PCB (UN1).

Code: E012-0000
Description: Drum Motor startup error
Causes: Revolution of the Drum Motor (M2) did not reach the specified value
Solutions: 1. Check the harness/connector between the Drum Motor (M2) and the Driver PCB (UN11). 2. Check the harness/connectors between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Drum Motor (M2). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1).

Code: E012-0001
Description: Drum Motor rotation error
Causes: Revolution of the Drum Motor (M2) was out of the specified range.
Solutions: 1. Check the harness/connector between the Drum Motor (M2) and the Driver PCB (UN11). 2. Check the harness/connectors between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Drum Motor (M2). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1).

Code: E014-0000
Description: Error in startup of the Fixing motors
Causes: Revolution of the Fixing Motor (M4) did not reach the specified value.
Solutions: 1. Check the harness/connector between the Fixing Motor (M4) and the Driver PCB (UN11). 2. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Fixing Motor (M4). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1).

Code: E014-0001
Description: Fixing Motor rotation error
Causes: Revolution of the Fixing Motor (M4) did not reach the specified value.
Solutions: 1. Check the harness/connector between the Fixing Motor (M4) and the Driver PCB (UN11). 2. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Fixing Motor (M4). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1).

Code: E015-0000
Description: Development engagement/disengagement error
Causes: The error was detected after the development disengagement operation.
Solutions: The error is likely caused by failure of the Developing Disengagement Solenoid (K) (SL2) / Developing Disengagement Solenoid (YMC) (SL4) or the Developing Disengagement Switch (K) (SW3) / Developing Disengagement Switch (YMC) (SW2). 1. Check the harness/connector between the Developing Disengagement Solenoid (K) (SL2) / Developing Disengagement Solenoid (YMC) (SL4) and the Driver PCB (UN11), and the harness/ connector between the Developing Disengagement Switch (K) (SW3) / Developing Disengagement Switch (YMC) (SW2) and the Driver PCB (UN11).2. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1).3. Replace the Developing Disengagement Switch (K) (SW3) or the Developing Disengagement Switch (YMC) (SW2).4. Replace the Developing Disengagement Solenoid (K) (SL2) or the Developing Disengagement Solenoid (YMC) (SL4).5. Replace the Driver PCB (UN11).6. Replace the Engine Controller PCB (UN1).

Code: E015-0001
Description: Pickup cassette (host machine) lift-up error
Causes: After lift-up of the Lifting Plate of the cassette of the host machine started, ON status of the Paper Surface Sensor of the cassette of the host machine was not detected within the specified period of time.
Solutions: 1. While the cassette of the host machine is removed, turn ON the power and insert the cassette, then check the operation sound of the Lifter Motor.When there is operation sound of the Lifter Motor, check if the Lifting Plate has been lifted up.<When the Lifting Plate has been lifted up>1. Check the harness/connector between the Cassette Feeder Driver PCB (UN20) and the Cassette Paper Surface Sensor (SR32) of the host machine.2. Replace the Cassette Paper Surface Sensor (SR32).3. Replace the Cassette Feeder Driver PCB (UN20).4. Replace the Engine Controller PCB (UN1).<When the Lifting Plate has not been lifted up>1. Check the condition of the gear at the host machine side (missing teeth, swing). 2. Check the harness/connector between the Lifter Solenoid (SL5) and the Engine Controller PCB (UN1).3. Check the harness/connector between the Pickup Motor (M1) and the Driver PCB (UN11). 4. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 5. Replace the Lifter Solenoid (SL5) 6. Replace the Pickup Motor (M1).7. Replace the Driver PCB (UN11).8. Replace the Engine Controller PCB (UN1).<When there is no operation sound of the motor>1. Check the harness/ connector between the Pickup Motor (M1) and the Driver PCB (UN11).2. Check the harness/ connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1).3. Replace the Pickup Motor (M1).4. Replace the Driver PCB (UN11).5. Replace the Engine Controller PCB (UN1).

Code: E015-0002
Description: Pickup Cassette (Option) lift-up error
Causes: After lift-up of the Lifting Plate of the 1st Paper Feeder started, ON status of the Paper Surface Sensor of the 1st Paper Feeder was not detected within the specified period of time.
Solutions: 1. While the cassette of the Paper Feeder is removed, turn ON the power and insert the cassette, then check the operation sound of the Lifter Motor.When there is operation sound of the Lifter Motor, check if the Lifting Plate has been lifted up.<When the Lifting Plate has been lifted up>1. Check the harness/connector between the Cassette Feeder Driver PCB (UN20) and the Cassette Paper Surface Sensor (SR32).2. Replace the Cassette Paper Surface Sensor (SR32).3. Replace the Cassette Feeder Driver PCB (UN20).<When the Lifting Plate has not been lifted up>1. Check the condition of the gear of the Paper Feeder (missing teeth, swing). 2. Check the harness/connector between the Lifter Solenoid (SL21) and the Cassette Feeder Driver PCB (UN20). 2. Check the harness/connector between the Cassette Feeder Driver PCB (UN20) and the Pickup Motor(M9).3. Replace the Pickup Motor (M9). 4. Replace the Lifter Solenoid (SL21). 5. Replace the Cassette Feeder Driver PCB (UN20).<When there is no operation sound of the motor>,1. Check the harness/connector between the Cassette Feeder Driver PCB (UN20) and the Pickup Motor (M9)2. Replace the Pickup Motor (M9).3. Replace the Cassette Feeder Driver PCB (UN20).

Code: E020-0000
Description: Color Displacement/Density Sensor error
Causes: An error in the Color Displacement/Density Sensor was detected.
Solutions: 1. Check the harness/connector between the RD Sensor (UN7) and the Engine Controller PCB (UN1). 2. Replace the RD Sensor (UN7). 3. Replace the Engine Controller PCB (UN1).

Code: E021-1000
Description: Yellow Developing Motor rotation error
Causes: It was judged that the Developing Motor did not rotate.
Solutions: 1. Check the harness/connector between the Developing Motor (M3) and the Driver PCB (UN11). 2. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Developing Motor (M3). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1)

Code: E021-1001
Description: Magenta Developing Motor rotation error
Causes: It was judged that the Developing Motor did not rotate.
Solutions: 1. Check the harness/connector between the Developing Motor (M3) and the Driver PCB (UN11). 2. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Developing Motor (M3). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1).

Code: E021-1002
Description: Cyan Developing Motor rotation error
Causes: It was judged that the Developing Motor did not rotate.
Solutions: 1. Check the harness/connector between the Developing Motor (M3) and the Driver PCB (UN11). 2. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Developing Motor (M3). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1).

Code: E021-1003
Description: Black Developing Motor rotation error
Causes: It was judged that the Developing Motor did not rotate.
Solutions: 1. Check the harness/connector between the Developing Motor (M3) and the Driver PCB (UN11). 2. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Developing Motor (M3). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1).

Code: E021-2000
Description: Error in startup of the Yellow Developing Motor
Causes: Revolution of the Developing Motor did not reach the specified value.
Solutions: 1. Check the harness/connector between the Developing Motor (M3) and the Driver PCB (UN11). 2. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Developing Motor (M3). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1).

Code: E021-2001
Description: Error in startup of the Magenta Developing Motor
Causes: Revolution of the Developing Motor did not reach the specified value.
Solutions: 1. Check the harness/connector between the Developing Motor (M3) and the Driver PCB (UN11). 2. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Developing Motor (M3). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1).

Code: E021-2002
Description: Error in startup of the Cyan Developing Motor
Causes: Revolution of the Developing Motor did not reach the specified value.
Solutions: 1. Check the harness/connector between the Developing Motor (M3) and the Driver PCB (UN11). 2. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Developing Motor (M3). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1).

Code: E021-2003
Description: Error in startup of the Black Developing Motor
Causes: Revolution of the Developing Motor did not reach the specified value.
Solutions: 1. Check the harness/connector between the Developing Motor (M3) and the Driver PCB (UN11). 2. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 3. Replace the Developing Motor (M3). 4. Replace the Driver PCB (UN11). 5. Replace the Engine Controller PCB (UN1).

Code: E052-0000
Description: Duplex Feed Unit absent error
Causes: Connection of the Duplex Feed Unit was not correct.
Solutions: 1. Replace the Engine Controller PCB (UN1).

Code: E066-0000
Description: Environment Sensor error
Causes: An error in the Environment Sensor was detected.
Solutions: 1. Check the harness/connection between the Engine Controller PCB (UN1) and the Environment Sensor PCB (UN10). 2. Replace the Environment Sensor PCB (UN10). 3. Replace the Engine Controller PCB (UN1).

Code: E078-0000
Description: Primary transfer disengagement mechanism error
Causes: Primary transfer disengagement mechanism did not work properly.
Solutions: 1. Check the harness/connector between the Primary Transfer Disengagement Switch (SW4) and the Engine Controller PCB (UN1). 2. Check the harness/connector between the Primary Transfer Disengagement Solenoid (SL30) and the Engine Controller PCB (UN1). 3. Replace the ITB Unit (including the Primary Transfer Disengagement Switch / Primary Transfer Disengagement Solenoid). 4. Replace the Engine Controller PCB (UN1).

Code: E100-0000
Description: Yellow Scanner area failure
Causes: Error in the Scanner Motor, Laser Scanner Unit, or BD detection in the yellow scanner area was detected.
Solutions: 1. Check the harness/connector between the Laser Scanner Unit and the Engine Controller PCB (UN1). 2. Replace the Laser Scanner Unit. 3. Replace the Engine Controller PCB (UN1).

Code: E100-0001
Description: Magenta Scanner area failure
Causes: Error in the Scanner Motor, Laser Scanner Unit, or BD detection in the magenta scanner area was detected.
Solutions: 1. Check the harness/connector between the Laser Scanner Unit and the Engine Controller PCB (UN1). 2. Replace the Laser Scanner Unit. 3. Replace the Engine Controller PCB (UN1).

Code: E100-0002
Description: Cyan Scanner area failure
Causes: Error in the Scanner Motor, Laser Unit, or BD detection in the cyan scanner area was detected.
Solutions: 1. Check the harness/connector between the Laser Scanner Unit and the Engine Controller PCB (UN1). 2. Replace the Laser Scanner Unit. 3. Replace the Engine Controller PCB (UN1).

Code: E100-0003
Description: Black scanner area failure
Causes: Error in the Scanner Motor, Laser Scanner Unit, or BD detection in the black scanner area was detected.
Solutions: 1. Check the harness/connector between the Laser Scanner Unit and the Engine Controller PCB (UN1). 2. Replace the Laser Scanner Unit. 3. Replace the Engine Controller PCB (UN1).

Code: E110-0000
Description: Pseudo BD detection error
Causes: The error is detected when the completion of pseudo BD measurement is not notified within the specified period of time after the pseudo BD generation.
Solutions: 1. Check the harness/connector between the Laser Scanner Unit and the Engine Controller PCB (UN1). 2. Replace the Laser Scanner Unit. 3. Replace the Engine Controller PCB (UN1).

Code: E194-0000
Description: Color Displacement/Density Sensor, Color Displacement Sensor error
Causes: An error in the Color Displacement/Density Sensor, Color Displacement Sensor were detected.
Solutions: 1. Replace the Toner Cartridge. 2. Check the harness/connector between the Color Displacement/Density Sensor and the Engine Controller PCB (UN1). 3. Replace the Color Displacement/Density Sensor. 4. Replace the Engine Controller PCB (UN1) 5. Replace the ITB Unit.

Code: E196-0000
Description: DC Controller error
Causes: Update of the DC Controller failed.
Solutions: 1. Install the set of controller firmware. 2. Replace the Engine Controller PCB (UN1).

Code: E196-1000
Description: ROM writing/reading error (Main ROM)
Causes: Error in the writing/reading of the main program in the Main Controller PCB (Main ROM)
Solutions: 1. Update the firmware. 2. Replace the Main Controller PCB (UN30).

Code: E196-2000
Description: ROM writing/reading error (Setting values storage ROM)
Causes: Error in the writing/reading the setting values storage area in the Main Controller PCB (Setting values storage ROM)
Solutions: 1. Update the firmware. 2. Replace the Main Controller PCB (UN30).

Code: E196-3000
Description: ROM writing/reading error (eMMC)
Causes: Unable to read/write data from the eMMC. The eMMC failure occurred.
Solutions: 1. Update the firmware. 2. Replace the Main Controller PCB (UN30).

Code: E196-3001
Description: ROM-ID mismatch (eMMC)
Causes: The eMMC was replaced incorrectly. The eMMC failure occurred.
Solutions: 1. Update the firmware. 2. Replace the Main Controller PCB (UN30).

Code: E198-0000
Description: Engine Controller memory failure
Causes: Error in the nonvolatile memory on the Engine Controller PCB
Solutions: 1. Turn OFF and then ON the power and check if the symptom occurs again. 2. Replace the Engine Controller PCB (UN1).

Code: E202-0001
Description: CIS Unit HP error (outward)
Causes: The Scanner (CIS) could not detect the home position when starting scanning operation.
Solutions: 1. Check the harnesses/connectors connecting from the Main Controller PCB (UN30) to the CIS Unit HP Sensor (SR11) and the Reader Motor (M5) 2. Replace the CIS HP Sensor (SR11). 3. Replace the Reader Motor (M5). 4. Replace the CIS Unit. 5. Replace the Reader Unit. 6. Replace the Main Controller PCB (UN30).

Code: E202-0002
Description: CIS Unit HP error (homeward)
Causes: The Scanner (CIS) could not detect the home position when completing scanning operation.
Solutions: 1. Check the harnesses/connectors connecting from the Main Controller PCB (UN30) to the CIS Unit HP Sensor (SR11) and the Reader Motor (M5) 2. Replace the CIS HP Sensor (SR11). 3. Replace the Reader Motor (M5). 4. Replace the CIS Unit. 5. Replace the Reader Unit. 6. Replace the Main Controller PCB (UN30).

Code: E225-0001
Description: Light intensity of the CIS Unit at the reference level or below
Causes: When the light intensity is at the reference level or below at shading.
Solutions: 1. Disconnect and then connect the Flexible Cable. 2. Replace the Flexible Cable. 3. Replace the CIS Unit. 4. Replace the Main Controller PCB (UN30).

Code: E246-0000
Description: System error
Causes: System error
Solutions: Contact the sales company.

Code: E247-0000
Description: System error
Causes: System error
Solutions: Contact the sales company.

Code: E248-0001
Description: Error in access to backup data for the Reader (reading error at power-on)
Causes: The Reader-related adjustment values could not be read.
Solutions: 1. Install the set of the controller firmware. 2. Replace the Main Controller PCB (UN30).

Code: E350-0000 … E355-0005
Description: System error
Causes: System error
Solutions: Contact the sales company.

Code: E719-0000
Description: Error in communication with the New Card Reader (serial communication)
Causes: Unable to communicate with the new Card Reader.
Solutions: 1. Check the connection of the New Card Reader.

Code: E732-0000
Description: Scanner communication error.
Causes: Scanner communication error
Solutions: 1. Install the set of the controller firmware. 2.Replace the Main Controller PCB (UN30).

Code: E733-0000
Description: Printer communication error
Causes: Communication error between the Engine Controller PCB and the Main Controller PCB occurred.
Solutions: 1. Check the harness/connector connection between the Engine Controller PCB (UN1) and the Main Controller PCB (UN30). 2. Install the set of the controller firmware. 3. Replace the Main Controller PCB (UN30). 4. Replace the Engine Controller PCB (UN1).

Code: E736-0000
Description: Fax communication error
Causes: Communication error with CCU/modem.
Solutions: 1. Check the connection of the NCU PCB (UN38). 2. Replace the NCU PCB (UN38). 3. Replace the Main Controller PCB (UN30).

Code: E736-0001
Description: Error in ROM for backing up fax data
Causes: An error occurred in ROM for backing up fax data.
Solutions: 1. Check the connection of the NCU PCB (UN38). 2. Replace the NCU PCB (UN38). 3. Replace the Main Controller PCB (UN30).

Code: E743-0000
Description: DDI communication error
Causes: Software sequence error
Solutions: 1. Turn OFF and then ON the power.

Code: E744-0001
Description: Incorrect combination of language file versions
Causes: Language file version did not match that of the main program.
Solutions: 1. Update the firmware

Code: E744-0002
Description: Language file error
Causes: The size of the language file exceeded the allowed size.
Solutions: 1. Update the firmware.

Code: E744-1001
Description: Version mismatch between BOOTABLE and BOOTROM
Causes: Version of the main program and that of the start-up program did not mach.
Solutions: 1. Update the firmware.

Code: E744-4000
Description: Invalid engine connection error
Causes: Invalid engine connection was detected.
Solutions: 1. Check if the valid Engine Controller PCB (UN1) is installed. 2. Update the firmware. 3. Replace the Engine Controller PCB (UN1).

Code: E744-5000
Description: Communication error between the Controller PCB and the Main Controller PCB
Causes: Communication with the Control Panel PCB could not be established.
Solutions: 1. Check the harness/connector between the Panel PCB (UN31) and the Main Controller PCB (UN30). 2. Replace the Control Panel (including the Panel PCB(UN31)). 3. Replace the Main Controller PCB (UN30).

Code: E744-6000
Description: Communication error with Wireless LAN PCB
Causes: Communication with the Wireless LAN PCB could not be established.
Solutions: 1. Turn OFF and then ON the main power. 2. Check the harness/connector connection between the Wireless LAN PCB (UN35) and the Main Controller PCB (UN30) 3. Install the set of the controller firmware. 4. Replace the Wireless LAN PCB (UN35). 5. Replace the Main Controller PCB (UN30).

Code: E744-7000
Description: Backup microcomputer error
Causes: An error in the microcomputer which retains fax job information of the Main Controller PCB.
Solutions: 1. Update the firmware. 2. Replace the Main Controller PCB (UN30).

Code: E746-0000
Description: Main Controller PCB error (others)
Causes: A communication error of the Main Controller PCB occurred (other than scan-related communication error).
Solutions: 1. Update the firmware. 2. Replace the Main Controller PCB (UN30).

Code: E766-8000
Description: Firmware error
Causes: Information on digital registration could not be obtained.
Solutions: 1. Install the Engine Controller firmware. 2. Install the set of Controller firmware. 3. Replace the Engine Controller (UN1).

Code: E766-9000
Description: Scanner power state error
Causes: Error in power state of the Laser Scanner Unit (firmware-dependent).
Solutions: 1. Update the firmware. 2. Replace the Laser Scanner Unit.

Code: E805-0005
Description: Cartridge Fan error
Causes: The Cartridge Fan failed to rotate at the specified revolution.
Solutions: 1. Check the connection of the Cartridge Fan (FM2). 2. Replace the Cartridge Fan (FM2).

Code: E806-0000
Description: Power Supply Fan error
Causes: The Power Supply Fan (power supply) failed to rotate at the specified revolution.
Solutions: 1. Check the connection of the Power Supply Fan. 2. Replace the Power Supply Fan (FM1).

Code: E808-0000
Description: Low voltage power supply failure
Causes: When the printer has detected a low voltage power supply failure.
Solutions: 1. Check the harness/connector between the Engine Controller PCB (UN1) and the Low Voltage Power Supply PCB (UN2). 2. Replace the Low Voltage Power Supply PCB (UN2). 3. Replace the Engine Controller PCB (UN1).

Code: E840-0000
Description: Pressure release mechanism error
Causes: An error in pressure release mechanism of the Fixing Assembly was detected.
Solutions: 1. Check the harness/connector between the Fixing Pressure Release Switch (SW5) and the Engine Controller PCB (UN1). 2. Check the harness/connector between the Fixing Motor (M4) and the Driver PCB (UN11). 3. Check the harness/connector between the Driver PCB (UN11) and the Engine Controller PCB (UN1). 4. Replace the Fixing Pressure Release Switch (SW5). 5. Replace the Fixing Motor (M4). 6. Replace the Fixing Assembly. 7. Replace the Driver PCB (UN11). 8. Replace the Engine Controller PCB (UN1).

About Canon Servie Tool V5610

– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.

– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.

Canon Service Tool V5610 Functions

– Fix Canon printer 7 times/ 8 times red light blinking:

– Fix Canon printer error code: 5B00, 5B01, 1700, 1701

Enter Service Mode on Canon Printer

1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.

– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-ts5320-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-fx-850-driver-firmware-and-manuals/

Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html

Contact us to get support with Canon MF742Cdw Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/

Repair Canon MF742Cdw Printer Error Codes Canon Servie Tool