Repair Canon MF732Cdw Printer Error Codes Canon Servie Tool

Repair Canon MF732Cdw Printer Error Codes Canon Servie Tool

– Printer model: Canon MF732Cdw
– Error codes on Canon MF732Cdw model and its description:

– Canon MF732Cdw printer Error Codes and quick guide to troubleshooting:

• Code: 0001
• Description: Delay Jam
• Causes: Document End Sensor
• Solutions: SR10 ADF Pickup Feed Area

• Code: 0002
• Description: Stationary Jam
• Causes: Document End Sensor
• Solutions: SR10 ADF Pickup Feed Area

• Code: 0021
• Description: Other
• Causes: Document End Sensor
• Solutions: SR10 ADF Pickup Feed Area

• Code: 0094
• Description: Power-on jam
• Causes: Document End Sensor
• Solutions: SR10 ADF Pickup Feed Area

• Code: 0104
• Description: Pickup Delay Jam 1
• Causes: Registration sensor/Multi-purpose Tray Paper Sensor/Cassette Feed Sensor
• Solutions: SR1/SR6/SR31 Cassette1/Multi-purpose Tray/Cassette2

• Code: 0105
• Description: Pickup Delay Jam 2
• Causes: Cassette Feed Sensor
• Solutions: SR31 Cassette2

• Code: 014C
• Description: Fixing Delivery Delay Jam1
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor
• Solutions: SR1/SR3/SR4 Cartridge to Fixing Roller Area

• Code: 016C
• Description: Delivery Delay Jam1
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor
• Solutions: SR1/SR3/SR4 Fixing Roller to Delivery Area

• Code: 0248
• Description: Pickup Stationary Jam 1
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor
• Solutions: SR1/SR3/SR4 Registration Area to Cartridge Cartridge to Fixing Roller Area

• Code: 0250
• Description: Fixing Delivery Stationary Jam 1
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor
• Solutions: SR1/SR3/SR4 Fixing Roller to Delivery Area

• Code: 025C
• Description: Wrap Jam1
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor
• Solutions: SR1/SR3/SR4 Cartridge to Fixing Roller Area Fixing Roller to Delivery Area

• Code: 025D
• Description: Wrap Jam2
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor
• Solutions: SR1/SR3/SR4/SR22 Cartridge to Fixing Roller Area Fixing Roller to Delivery Area

• Code: 0260
• Description: Reverse Area Jam1
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor
• Solutions: SR1/SR3/SR4/SR22 Fixing Roller to Delivery Area

• Code: 0270
• Description: Delivery Stationary Jam 1
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor
• Solutions: SR1/SR3/SR4 Fixing Roller to Delivery Area

• Code: 029D
• Description: Wrap Jam2
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor
• Solutions: SR1/SR3/SR4/SR22 Duplex Re-pickup Assembly

• Code: 02A0
• Description: Reverse Area Jam1
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor
• Solutions: SR1/SR3/SR4/SR22 Duplex Re-pickup Assembly

• Code: 02A4
• Description: Duplex Re-pickup Assembly Jam1
• Causes: Duplex Re-pickup Sensor
• Solutions: SR22 Duplex Re-pickup Assembly

• Code: 02A5
• Description: Duplex Re-pickup Assembly Jam2
• Causes: Duplex Re-pickup Sensor
• Solutions: SR22 Duplex Re-pickup Assembly

• Code: 02CD
• Description: Wrap Jam2
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor
• Solutions: SR1/SR3/SR4/SR22 Registration Area to Delivery Area Duplex Re-pickup Assembly

• Code: 02E0
• Description: Reverse Area Jam1
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor
• Solutions: SR1/SR3/SR4/SR22 Registration Area to Delivery Area Duplex Re-pickup Assembly

• Code: 10-0401
• Description: Toner Bottle empty alarm (Y)
• Causes: When the Toner Bottle empty was detected
• Solutions:

• Code: 10-0402
• Description: Toner Bottle empty alarm (M)
• Causes: When the Toner Bottle empty was detected
• Solutions:

• Code: 10-0403
• Description: Toner Bottle empty alarm (C)
• Causes: When the Toner Bottle empty was detected
• Solutions:

• Code: 10-0404
• Description: Toner Bottle empty alarm (BK)
• Causes: When the Toner Bottle empty was detected
• Solutions:

• Code: 1014
• Description: Power ON Jam 1
• Causes: Cassette Feed Sensor
• Solutions: SR31 Cassette2

• Code: 1017
• Description: Power ON Jam 4
• Causes: Cassette Feed Sensor
• Solutions: SR31 Cassette2

• Code: 1054
• Description: Power ON Jam 1
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor
• Solutions: SR1/SR3/SR4/SR22 Registration Area to Delivery Area

• Code: 1057
• Description: Power ON Jam 4
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor
• Solutions: SR1/SR3/SR4/SR22 Registration Area to Delivery Area

• Code: 1094
• Description: Power ON Jam 1
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor
• Solutions: SR1/SR3/SR4/SR22 Duplex Re-pickup Assembly

• Code: 1097
• Description: Power ON Jam 4
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor
• Solutions: SR1/SR3/SR4/SR22 Duplex Re-pickup Assembly

• Code: 10D4
• Description: Power ON Jam 1
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor
• Solutions: SR1/SR3/SR4/SR22 Registration Area to Delivery Area Duplex Re-pickup Assembly

• Code: 10D7
• Description: Power ON Jam 4
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor
• Solutions: SR1/SR3/SR4/SR22 Registration Area to Delivery Area Duplex Re-pickup Assembly

• Code: 1118
• Description: Door Open Jam1
• Causes: Registration sensor/Multi-purpose Tray Paper Sensor/Cassette Feed Sensor
• Solutions: SR1/SR6/SR31 Cassette1/Multi-purpose Tray/Cassette2

• Code: 1158
• Description: Door Open Jam1
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor
• Solutions: SR1/SR3/SR4/SR22 Registration Area to Delivery Area

• Code: 1198
• Description: Door Open Jam1
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor
• Solutions: SR1/SR3/SR4/SR22 Duplex Re-pickup Assembly

• Code: 11D8
• Description: Door Open Jam1
• Causes: Registration sensor/Fixing Delivery Sensor/Delivery Sensor/Duplex Re-pickup Sensor
• Solutions: SR1/SR3/SR4/SR22 Registration Area to Delivery Area Duplex Re-pickup Assembly

• Code: E000-0000
• Description: Error in temperature rising of Fixing Assembly
• Causes: Temperature of the Fixing Assembly did not reach a certain temperature within the specified period of time.
• Solutions: 1. Check the connector connection between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB.

• Code: E001-0000
• Description: Abnormal high temperature of Fixing Assembly
• Causes: It was detected that the temperature of the Fixing Assembly was abnormally high.
• Solutions: 1. Check the connector connection between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB.

• Code: E001-0001
• Description: Abnormal high temperature of Fixing Assembly
• Causes: It was detected that the temperature of the Fixing Assembly (Sub Thermistor) was abnormally high.
• Solutions: 1. Check the connector connection between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB.

• Code: E003-0000
• Description: Abnormal low temperature of Fixing Assembly
• Causes: It was detected that the temperature of the Fixing Assembly was abnormally low.
• Solutions: 1. Check the connector connection between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB.

• Code: E003-0001
• Description: It was detected that the temperature of the Fixing Assembly (Sub Thermistor) was abnormally low.
• Causes: It was detected that the temperature of the Fixing Assembly (Sub Thermistor) was abnormally low.
• Solutions: 1. Check the connector connection between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB.

• Code: E004-0000
• Description: Error in fixing power supply drive circuit
• Causes: The zero cross signal was not detected for the specified period of time or more.
• Solutions: 1. Check the connector connection between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB.

• Code: E012-0000
• Description: Black Drum Motor error
• Causes: An error in the initial operation of the Drum Motor was detected.
• Solutions: 1. Reconnect the connector of the Main Motor. 2. Replace the Engine Controller PCB.

• Code: E012-0001
• Description: Black Drum Motor error
• Causes: Rotation error of the Drum Motor was detected.
• Solutions: 1. Reconnect the connector of the Main Motor. 2. Replace the Engine Controller PCB.

• Code: E014-0000
• Description: Error in startup of the Main Motor
• Causes: Revolution of the Main Motor did not reach the specified value.
• Solutions: 1. Check the connector connection between the Main Motor and the Engine Controller PCB. 2. Replace the Main Motor. 3. Replace the Engine Controller PCB.

• Code: E014-0001
• Description: Error in startup of the Main Motor
• Causes: Revolution of the Main Motor was out of the specified range.
• Solutions: 1. Check the connector connection between the Main Motor and the Engine Controller PCB. 2. Replace the Main Motor. 3. Replace the Engine Controller PCB.

• Code: E015-0000
• Description: Error in Developing Disengagement Motor
• Causes: The engine detected an error in the Developing Disengagement Motor.
• Solutions: 1. Check the harnesses/connectors connecting the Developing Disengagement Switch, the Developing Disengagement Solenoid and the Engine Controller PCB. 2. Check that the Developing Disengagement Switch is properly installed. 3. Replace the Developing Disengagement Switch. 4. Replace the Developing Disengagement Solenoid. 5. Replace the Engine Controller PCB.

• Code: E015-0001
• Description: Cassette 1 lift-up error
• Causes: After lift-up of the Lifting Plate of the cassette of the host machine started, ON status of the Lifter Sensor of the cassette of the host machine was not detected within the specified period of time.
• Solutions: 1. While the cassette of the host machine is removed, turn ON the power and insert the cassette, then check the operation sound of the motor. When there is operation sound of the motor, check if the Lifting Plate has been lifted up. When the Lifting Plate has been lifted up: 1-1. Check that the Lifter Sensor of the cassette of the host machine is properly installed. 1-2. Check the harness/connector between the Engine Controller PCB and the Lifter Sensor. 1-3. Replace the Lifter Sensor.1-4. Replace the Engine Controller PCB. When the Lifting Plate has not been lifted up: 2-1. Check the condition of the gear at the host machine side (missing teeth, swing). 2-2. Check the harness/connector between the Engine Controller PCB and the Lifter Solenoid of the cassette of the host machine. 2-3. Replace the Lifter Solenoid. 2-4. Replace the Pickup Motor of the cassette of the host machine. 2-5. Replace the Driver PCB. 2-6. Replace the Engine Controller PCB. When there is no operation sound of the motor, check the followings: 3-1. Check the harness/connector between the Engine Controller PCB and the Pickup Motor of the cassette of the host machine. 3-2. Check the condition of the gear at the host machine side (missing teeth, swing). 3-3. Check the Pickup Motor. 3-4. Replace the Driver PCB. 3-5. Replace the Engine Controller PCB.

• Code: E015-0002
• Description: Cassette 2 lift-up error
• Causes: After lift-up of the Lifting Plate of the 1-Cassette Unit started, ON status of the Lifter Sensor of the 1-Cassette Unit was not detected within the specified period of time.
• Solutions: 1. While the cassette of the 1-Cassette Unit is removed, turn ON the power and insert the cassette, then check the operation sound of the motor. When there is operation sound of the motor, check if the Lifting Plate has been lifted up. When the Lifting Plate has been lifted up: 1-1. Check that the Lifter Sensor of the Cassette Unit is properly installed. 1-2. Check the harness/connector between the Engine Controller PCB and the Lifter Sensor. 1-3. Replace the Lifter Sensor. 1-4. Replace the Cassette Feeder Driver PCB. 1-5. Replace the Engine Controller PCB. When the Lifting Plate has not been lifted up: 2-1. Check the condition of the gear of the Cassette Unit (missing teeth, swing). 2-2. Check the harness/connector between the Engine Controller PCB and the Lifter Solenoid of the Cassette Unit. 2-3. Replace the Lifter Solenoid. 2-4. Replace the Pickup Motor of the Cassette Unit. 2-5. Replace the Cassette Feeder Driver PCB. 2-6. Replace the Engine Controller PCB. When there is no operation sound of the motor, check the followings: 3-1. Check the harness/connector between the Engine Controller PCB and the Pickup Motor of the Cassette Unit. 3-2. Check the condition of the gear at the Cassette Unit side (missing teeth, swing). 3-3. Replace the Pickup Motor. 3-4. Replace the Cassette Feeder Driver PCB. 3-5. Replace the Engine Controller PCB.

• Code: E020-0000
• Description: Density Sensor error
• Causes: An error in the Density Sensor was detected.
• Solutions: 1. Check the remaining toner level. 2. Replace the Toner Cartridge. 3. Check the harness/connector between the Color Displacement/Density Sensor and the Engine Controller PCB. 4. Replace the Color Displacement/Density Sensor. 5. Replace the ITB. 6. Replace the Engine Controller PCB.

• Code: E021-1000
• Description: Yellow Developing Motor rotation error
• Causes: It was judged that the Developing Motor did not rotate.
• Solutions: 1. Check the harness/connector between the Developing Motor and the Engine Controller PCB. 2. Replace the Developing Motor. 3. Replace the Driver PCB. 4. Replace the Engine Controller PCB.

• Code: E021-1001
• Description: Magenta Developing Motor rotation error
• Causes: It was judged that the Developing Motor did not rotate.
• Solutions: 1. Check the harness/connector between the Developing Motor and the Engine Controller PCB. 2. Replace the Developing Motor. 3. Replace the Driver PCB. 4. Replace the Engine Controller PCB.

• Code: E021-1002
• Description: Cyan Developing Motor rotation error
• Causes: It was judged that the Developing Motor did not rotate.
• Solutions: 1. Check the harness/connector between the Developing Motor and the Engine Controller PCB. 2. Replace the Developing Motor. 3. Replace the Driver PCB. 4. Replace the Engine Controller PCB.

• Code: E021-1003
• Description: Black Developing Motor rotation error
• Causes: It was judged that the Developing Motor did not rotate.
• Solutions: 1. Check the harness/connector between the Developing Motor and the Engine Controller PCB. 2. Replace the Developing Motor. 3. Replace the Driver PCB. 4. Replace the Engine Controller PCB.

• Code: E021-2000
• Description: Error in startup of the Yellow Developing Motor
• Causes: Revolution of the Developing Motor did not reach the specified value.
• Solutions: 1. Check the harness/connector between the Developing Motor and the Engine Controller PCB. 2. Replace the Developing Motor. 3. Replace the Driver PCB. 4. Replace the Engine Controller PCB.

• Code: E021-2001
• Description: Error in startup of the Magenta Developing Motor
• Causes: Revolution of the Developing Motor did not reach the specified value.
• Solutions: 1. Check the harness/connector between the Developing Motor and the Engine Controller PCB. 2. Replace the Developing Motor. 3. Replace the Driver PCB. 4. Replace the Engine Controller PCB.

• Code: E021-2002
• Description: Error in startup of the Cyan Developing Motor
• Causes: Revolution of the Developing Motor did not reach the specified value.
• Solutions: 1. Check the harness/connector between the Developing Motor and the Engine Controller PCB. 2. Replace the Developing Motor. 3. Replace the Driver PCB. 4. Replace the Engine Controller PCB.

• Code: E021-2003
• Description: Error in startup of the Black Developing Motor
• Causes: Revolution of the Developing Motor did not reach the specified value.
• Solutions: 1. Check the harness/connector between the Developing Motor and the Engine Controller PCB. 2. Replace the Developing Motor. 3. Replace the Driver PCB. 4. Replace the Engine Controller PCB.

• Code: E052-0000
• Description: Duplex Feed Unit absent error
• Causes: Connection of the Duplex Feed Unit was not correct.
• Solutions: 1. Reinstall the Duplex Feed Unit.

• Code: E066-0000
• Description: Environment Sensor error
• Causes: An error in the Environment Sensor was detected.
• Solutions: 1. Check the harness/connection of the Environment Sensor and the Engine Controller PCB. 2. Replace the Environment Sensor. 3. Replace the Engine Controller PCB.

• Code: E078-0000
• Description: Primary transfer disengagement mechanism error
• Causes: Primary transfer disengagement mechanism did not work properly.
• Solutions: 1. Check the harnesses/connectors connecting the Primary Transfer Disengagement Switch, the Primary Transfer Disengagement Solenoid and the Engine Controller PCB. 2. Replace the Primary Transfer Disengagement Switch. 3. Replace the Primary Transfer Disengagement Solenoid. 4. Replace the Engine Controller PCB.

• Code: E100-0000
• Description: Yellow scanner area failure
• Causes: Error in the Scanner Motor, Laser Unit, or BD detection in the yellow scanner area
• Solutions: 1. Check the harness/FFC/connector between the Laser Unit and the Engine Controller PCB. 2. Replace the FFC. 3. Replace the Laser Unit. 4. Replace the Engine Controller PCB.

• Code: E100-0001
• Description: Magenta scanner area failure
• Causes: Error in the Scanner Motor, Laser Unit, or BD detection in the magenta scanner area
• Solutions: 1. Check the harness/FFC/connector between the Laser Unit and the Engine Controller PCB. 2. Replace the FFC. 3. Replace the Laser Unit. 4. Replace the Engine Controller PCB.

• Code: E100-0002
• Description: Cyan scanner area failure
• Causes: Error in the Scanner Motor, Laser Unit, or BD detection in the cyan scanner area
• Solutions: 1. Check the harness/FFC/connector between the Laser Unit and the Engine Controller PCB. 2. Replace the FFC. 3. Replace the Laser Unit. 4. Replace the Engine Controller PCB.

• Code: E100-0003
• Description: Black scanner area failure
• Causes: Error in the Scanner Motor, Laser Unit, or BD detection in the black scanner area
• Solutions: 1. Check the harness/FFC/connector between the Laser Unit and the Engine Controller PCB. 2. Replace the FFC. 3. Replace the Laser Unit. 4. Replace the Engine Controller PCB.

• Code: E110-0000
• Description: Primary pseudo BD correction error
• Causes: The scanner failed to be Ready within 3 seconds after start of pseudo BD control.
• Solutions: 1. Check that the engine test print is properly printed. 2. Check the FFC between the Main Controller PCB and the Engine Controller PCB. 3. Replace the Main Controller PCB.

• Code: E194-0000
• Description: CPR Sensor error
• Causes: An error in the CPR Sensor was detected.
• Solutions: 1. Replace the Toner Cartridge. 2. Check the harness/connector between the Color Displacement/Density Sensor and the Engine Controller PCB. 3. Replace the Color Displacement/Density Sensor Unit. 4. Replace the Engine Controller PCB. 5. Replace the ITB Unit.

• Code: E196-0000
• Description: Engine Controller error
• Causes: Update of the Engine Controller was failed. (RFU mode right after the startup)
• Solutions: 1. Replace the Engine Controller PCB.

• Code: E198-0000
• Description: Engine Controller memory failure
• Causes: Error in the nonvolatile memory on the Engine Controller PCB
• Solutions: 1. Turn OFF and then ON the power and check if the symptom occurs again. 2. Replace the Engine Controller PCB.

• Code: E202-0001
• Description: CIS Unit HP error (outward)
• Causes: The CIS Unit did not move to HP even it moved backward. Reader HP Sensor error, Reader Motor error, CIS Unit error
• Solutions: 1. Replace the Reader HP Sensor. 2. Replace the Reader Motor. 3. Replace the CIS Unit. 4. Replace the Reader Unit.

• Code: E202-0002
• Description: CIS Unit HP error (homeward)
• Causes: The CIS Unit did not move to HP even it moved forward. Reader HP Sensor error, Reader Motor error, CIS Unit error
• Solutions: 1. Replace the Reader HP Sensor. 2. Replace the Reader Motor. 3. Replace the CIS Unit. 4. Replace the Reader Unit.

• Code: E246-0000
• Description: System error
• Causes: System error
• Solutions: Contact the sales company.

• Code: E247-0000
• Description: System error
• Causes: System error
• Solutions: Contact the sales company.

• Code: E302-0001
• Description: Shading error
• Causes: When the light intensity is below the reference level at shading
• Solutions: 1. Disconnect and then connect the Flexible Cable. 2. Replace the Flexible Cable. 3. Replace the CIS Unit. 4. Replace the Main Controller PCB (PCB2).

• Code: E302-0002
• Description: Shading error
• Causes: Image sampling for shading was not completed.
• Solutions: 1. Turn OFF and then ON the main power. 2. Check the connection of the harness. 3. Replace the Main Controller PCB. 4. Replace the Reader Unit.

• Code: E350-0000
• Description: System error
• Causes: System error
• Solutions: Contact the sales company.

• Code: E354-0000
• Description: System error
• Causes: System error
• Solutions: Contact the sales company.

• Code: E355-0000
• Description: System error
• Causes: System error
• Solutions: Contact the sales company.

• Code: E355-0004
• Description: System error
• Causes: System error
• Solutions: Contact the sales company.

• Code: E355-0005
• Description: System error
• Causes: System error
• Solutions: Contact the sales company.

• Code: E732-0000
• Description: Scanner communication error
• Causes: Scanner communication error
• Solutions: 1. Install the set of the controller firmware. 2. Replace the Main Controller PCB.

• Code: E733-0000
• Description: Printer communication error
• Causes: Communication error between the Engine Controller PCB and the Main Controller PCB occurred.
• Solutions: 1. Check the connector connection between the Engine Controller PCB and the Main Controller PCB. 2. Install the set of the controller firmware. 3. Replace the Main Controller PCB. 4. Replace the Engine Controller PCB.

• Code: E743-0000
• Description: DDI communication error
• Causes: Software sequence error
• Solutions: 1. Turn OFF and then ON the main power.

• Code: E805-0005
• Description: Sub Fan error
• Causes: The Sub Fan was locked for a specified consecutive period of time.
• Solutions: 1. Check the connection of the Sub Fan. 2. Replace the Sub Fan.

• Code: E806-0000
• Description: Main Fan error
• Causes: The Main Fan was locked for a specified consecutive period of time.
• Solutions: 1. Check the connection of the Main Fan. 2. Replace the Main Fan.

• Code: E808-0000
• Description: Low-voltage power supply failure detection
• Causes: Printer detected low-voltage power supply failure.
• Solutions: 1. Replace the Engine Controller PCB

• Code: E840-0000
• Description: Pressure release mechanism error
• Causes: An error in pressure release mechanism of the Fixing Assembly was detected.
• Solutions: 1. Replace the Fixing Assembly. 2. Replace the Fixing Motor.

About Canon Servie Tool V5610

– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.

– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.

Canon Service Tool V5610 Functions

– Fix Canon printer 7 times/ 8 times red light blinking:

– Fix Canon printer error code: 5B00, 5B01, 1700, 1701

Enter Service Mode on Canon Printer

1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.

– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-imageclass-2200-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-cx6000-driver-firmware-and-manuals/

Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html

Contact us to get support with Canon MF732Cdw Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/