Repair Canon MF6140dn Printer Error Codes Canon Servie Tool
– Printer model: Canon MF6140dn
– Error codes on Canon MF6140dn model and its description:
– Canon MF6140dn printer Error Codes and quick guide to troubleshooting:
- Code: E000 0000
- Description: Error in temperature rising of Fixing Assembly
- Causes: Temperature of the Fixing Assembly did not reach a certain temperature within the specified period of time.
- Solutions: 1. Check the connector between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB.
- Code: E001 0000
- Description: Abnormal high temperature of Fixing Assembly
- Causes: It was detected that the temperature of the Fixing Assembly was abnormally high.
- Solutions: 1. Check the connector between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB.
- Code: E003 0000
- Description: Abnormal low temperature of Fixing Assembly
- Causes: It was detected that the temperature of the Fixing Assembly was abnormally low.
- Solutions: 1. Check the connector between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB.
- Code: E004 0000
- Description: Error in fixing power supply drive circuit
- Causes: Failed to detect the zero cross signal for the specified period of time or more.
- Solutions: 1. Check the connection of connector between the Fixing Assembly and the Engine Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the Engine Controller PCB.
- Code: E014 0000
- Description: Error in startup of the Main Motor
- Causes: Revolution of the Main Motor did not reach the specified value.
- Solutions: 1. Check the connection of connector between the Main Motor and the Engine Controller PCB. 2. Replace the Main Motor. 3. Replace the Engine Controller PCB.
- Code: E100 0000
- Description: Laser Scanner Assembly error
- Causes: At the Laser Scanner Unit, BD cycle was not within the specified range.
- Solutions: 1. Check the connection of connector between the Main Controller PCB and the Laser Scanner Unit. 2. Check the connection of connector between the Relay PCB and the Laser Scanner Unit. 3. Replace the Laser Scanner Unit.
- Code: E196 1000
- Description: Main Controller PCB reading/writing error
- Causes: Error in reading/writing of main program in the Main Controller PCB
- Solutions: 1. Install the set of the controller firmware. 2. Replace the Main Controller PCB.
- Code: E196 2000
- Description: Main Controller PCB reading/writing error
- Causes: Error in reading/writing of setting values storage area in the Main Controller PCB
- Solutions: 1. Install the set of the controller firmware. 2. Replace the Main Controller PCB.
- Code: E202 0001
- Description: CIS Unit HP error (outward)
- Causes: CIS Unit did not move to HP even it moved backward. Reader HP Sensor error, Reader Motor error, CIS Unit error
- Solutions: 1. Replace the Reader HP Sensor. 2. Replace the Reader Motor. 3. Replace the CIS Unit. 4. Replace the Reader Unit.
- Code: E202 0002
- Description: CIS Unit HP error (homeward)
- Causes: CIS Unit did not move to HP even it moved forward. Reader HP Sensor error, Reader Motor error, CIS Unit error
- Solutions: 1. Replace the Reader HP Sensor. 2. Replace the Reader Motor. 3. Replace the CIS Unit. 4. Replace the Reader Unit.
- Code: E248 0001
- Description: Error in access to backup data for Reader (reading error at power-on)
- Causes: The Reader-related adjustment values could not be read.
- Solutions: 1. Clear the backup RAM of RCON. Execute COPIER>FUNCTION>CLEAR>RCON. 2. Enter all the values written on the service label in service mode again. 3. Turn OFF and then ON the main power. 4. Replace the Main Controller PCB.
- Code: E351 0000
- Description: System error
- Causes: System error
- Solutions: 1. Install the set of the controller firmware. 2. Replace the Main Controller PCB.
- Code: E733 0000
- Description: Printer communication error
- Causes: Communication error between the Engine Controller PCB and the Main Controller PCB occurred.
- Solutions: 1. Check the connection of connector between the Engine Controller PCB and the Main Controller PCB. 2. Install the set of the controller firmware. 3. Replace the Main Controller PCB. 4. Replace the Engine Controller PCB.
- Code: E736 0000
- Description: Communication error with CCU/modem
- Causes: Communication error with CCU/modem. NCU PCB type error.
- Solutions: 1. Install the set of the controller firmware. 2. Replace the NCU PCB. 3. Replace the Main Controller PCB.
- Code: E744 0001
- Description: Language file version error
- Causes: Language file version was not matched with the main program.
- Solutions: Install the set of the controller firmware.
- Code: E744 0002
- Description: Language file size error
- Causes: The size of the language file exceeded the upper limit.
- Solutions: Install the set of the controller firmware.
- Code: E744 1001
- Description: Firmware version error
- Causes: Version of the main program and the version of the start-up program was not matched.
- Solutions: Install the set of the controller firmware.
- Code: E744 4000
- Description: Engine ID error
- Causes: Invalid engine connection was detected.
- Solutions: 1. Turn OFF and then ON the main power. 2. Check the Engine Controller PCB. 3. Install the Engine Controller PCB. 4. Install the set of the controller firmware. 5. Check the model code. (When the model code and the engine code are mismatched, E744-4000 occurs.)
- Code: E744 5000
- Description: Error in the Control Panel PCB
- Causes: Error in the Control Panel PCB (microcomputer).
- Solutions: 1. Check the Control Panel PCB, and install the firmware (PANEL). 2. Install the set of the controller firmware. 3. Replace the Main Controller PCB.
- Code: E744 6000
- Description: Communication error with the Wireless LAN PCB
- Causes: Unable to communicate with the Wireless LAN.
- Solutions: 1. Turn OFF and then ON the main power. 2. Check the connection of the Wireless LAN. 3. Install the set of the controller firmware. 4. Replace the Main Controller PCB.
- Code: E744 7000
- Description: Main Controller PCB error
- Causes: An error in the microcomputer which retains fax job information of the Main Controller PCB.
- Solutions: 1. Install the firmware of BKUP. 2. Install the set of the controller firmware. 3. Replace the Main Controller PCB.
- Code: E746 0000
- Description: Main Controller PCB error
- Causes: Main Controller communication error occurred (other than scan).
- Solutions: 1. Install the set of the controller firmware. 2. Replace the Main Controller PCB.
- Code: E766 8000
- Description: Digital registration error
- Causes: Information at digital registration could not be obtained.
- Solutions: 1. Install the Engine Controller firmware. 2. Install the set of the controller firmware. 3. Replace the Engine Controller PCB.
- Code: E766 9000
- Description: Scanner power state error
- Causes: An error was detected in power state of the Laser Scanner Unit.
- Solutions: 1. Install the set of the controller firmware. 2. Replace the Laser Scanner Unit.
- Code: E766 xxxx*1
- Description: Firmware error
- Causes: An error due to the controller software occurred so that print could not be proceeded. *1 Task number related to Exception is shown in decimal
- Solutions: Due to firmware error, the possibility of solving the error by replacing the Main Controller PCB is low. Check the installed engine again.
- Code: E804 0004
- Description: Controller Fan error
- Causes: Since the startup of the Controller Fan, the Fan was locked for a specified consecutive period of time.
- Solutions: 1. Check power supply to the Controller Fan. 2. Replace the Controller Fan.
- Code: E805 0000
- Description: Main Fan error
- Causes: The Main Fan was locked for a specified consecutive period of time.
- Solutions: 1. Check the connection of the Main Fan. 2. Replace the Main Fan.
- Code: E808 0000
- Description: Failure detection of Low Voltage Power Supply PCB
- Causes: Printer detected failure of the Low Voltage Power Supply PCB.
- Solutions: Replace the Engine Controller PCB.
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-ix6520-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-wf-7710-driver-firmware-and-manuals/
Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html
Contact us to get support with Canon MF6140dn Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
