Repair Canon MF3010 Printer Error Codes Canon Servie Tool

Repair Canon MF3010 Printer Error Codes Canon Servie Tool

– Printer model: Canon MF3010
– Error codes on Canon MF3010 model and its description:

– Canon MF3010 printer Error Codes and quick guide to troubleshooting:

• Code: E000
• Description: Startup failure
• Solutions: (1) Check the connectors of the Fixing Assembly. (J101, J1011, J552 and J702)
  (2) Replace the Fixing Assembly.
  (3) Replace the Engine Controller PCB.

• Code: E001
• Description: Abnormal high temperature
• Solutions: (1) Check the connectors of the Fixing Assembly. (J101, J1011, J552 and J702)
  (2) Replace the Fixing Assembly.
  (3) Replace the Engine Controller PCB.

• Code: E003
• Description: Abnormal low temperature
• Solutions: (1) Check the connectors of the Fixing Assembly. (J101, J1011, J552 and J702)
  (2) Replace the Fixing Assembly.
  (3) Replace the Engine Controller PCB.

• Code: E004
• Description: Fixing heater drive circuit error (200V models only)
• Solutions:

• Code: E100
• Description: Scanner area failure
• Solutions: (1) Check the connectors of the Fixing Assembly. (J101, J1011, J552 and J702)
  (2) Replace the Fixing Assembly.
  (3) Replace the Engine Controller PCB.

• Code: E196
• Description: ROM read/write error (error in storing setting values in user mode/service mode/ factory mode)
• Solutions: When the same error repeatedly occurs although the power is turned OFF and then ON for several times, execute the following remedies.
  (1) Update the firmware of the Main Controller PCB.
  (2) Replace the Main Controller PCB.

• Code: E202
• Description: CIS Unit home position detection error / homeward reading position error
• Solutions: When the same error repeatedly occurs although the power is turned OFF and then ON for several times, execute the following remedies.
  (1) Check the connection between the Main Controller PCB and the CIS Unit. (J2)
  (2) Replace CIS Unit.
  (3) Check the connection between the Main Controller PCB and the Reader Motor (M3). (J11)
  (4) Replace the Reader Motor (M3).
  (5) Replace the Main Controller PCB.

• Code: E225
• Description: Insufficient lamp light intensity (The light intensity is at the reference level or below.)
• Solutions: When the same error repeatedly occurs although the power is turned OFF and then ON for several times, execute the following remedies.
  (1) Check the connection between the Main Controller PCB and the CIS Unit. (J2)
  (2) Replace CIS Unit.
  (3) Replace the Main Controller PCB.

• Code: E301
• Description: Insufficient light intensity at shading
• Solutions: When the same error repeatedly occurs although the power is turned OFF and then ON for several times, execute the following remedies.
  (1) Check the connection between the Main Controller PCB and the CIS Unit. (J2)
  (2) Replace CIS Unit.
  (3) Replace the Main Controller PCB.

• Code: E744
• Description: System error
• Solutions: When the same error repeatedly occurs although the power is turned OFF and then ON for several times, execute the following remedies.
  (1) Replace the Main Controller PCB.
  (2) Replace the Engine Controller PCB.

About Canon Servie Tool V5610

– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.

– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.

Canon Service Tool V5610 Functions

– Fix Canon printer 7 times/ 8 times red light blinking:

– Fix Canon printer error code: 5B00, 5B01, 1700, 1701

Enter Service Mode on Canon Printer

1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.

– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-d340-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-sc-s80600-driver-firmware-and-manuals/

Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html

Contact us to get support with Canon MF3010 Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/