Repair Canon MF269dw Printer Error Codes Canon Servie Tool
– Printer model: Canon MF269dw
– Error codes on Canon MF269dw model and its description:
– Canon MF269dw printer Error Codes and quick guide to troubleshooting:
- Code: 0001
- Description: Pickup delay jam
- Causes: Document End Sensor DADF: PS6 SADF: PS8
- Solutions:
- Code: 0002
- Description: Pickup stationary Jam
- Causes: TOP Sensor PS3
- Solutions:
- Code: 0002
- Description: Pickup stationary Jam
- Causes: Document End Sensor DADF: PS6 SADF: PS8
- Solutions:
- Code: 0003
- Description: Fixing delivery delay Jam
- Causes: Fixing Delivery Sensor PS4
- Solutions:
- Code: 0004
- Description: Fixing delivery stationary Jam
- Causes: Fixing Delivery Sensor PS4
- Solutions:
- Code: 0007
- Description: Reverse Assembly Jam
- Causes: Fixing Delivery Sensor PS4
- Solutions:
- Code: 000B
- Description: 2-sided re-pickup delay Jam
- Causes: TOP Sensor PS3
- Solutions:
- Code: 000C
- Description: Wrapping Jam
- Causes: Fixing Delivery Sensor PS4
- Solutions:
- Code: 000E
- Description: Internal residual Jam
- Causes: TOP Sensor/Fixing Delivery Sensor/Fixing Paper Width Sensor PS3/PS4/PS5
- Solutions:
- Code: 000F
- Description: Door open Jam
- Causes: TOP Sensor/Fixing Delivery Sensor/Fixing Paper Width Sensor PS3/PS4/PS5
- Solutions:
- Code: 0071
- Description: Sequence Jam (abnormal timing)
- Causes: Document End Sensor DADF: PS6 SADF: PS8
- Solutions:
- Code: 0094
- Description: Internal residual Jam
- Causes: Document End Sensor DADF: PS6 SADF: PS8
- Solutions:
- Code: 0095
- Description: Others
- Causes: Document End Sensor DADF: PS6 SADF: PS8
- Solutions:
- Code: E000-0000
- Description: Fixing temperature control startup failure
- Causes: Temperature of the Fixing Unit does not reach the specified temperature within the specified period of time.
- Solutions: 1. Check the harness/connector of the Fixing Unit. 2. Replace the Fixing Film Unit. 3. Replace the Fixing Unit. 4. Replace the Engine Controller PCB.
- Code: E001-0000
- Description: Abnormal high temperature of the Fixing Unit
- Causes: It was detected that the temperature of the Fixing Unit was abnormally high.
- Solutions: 1. Check the harness/connector of the Fixing Unit. 2. Replace the Fixing Film Unit. 3. Replace the Fixing Unit. 4. Replace the Engine Controller PCB.
- Code: E003-0000
- Description: Abnormal low temperature of the Fixing Assembly
- Causes: It was detected that the temperature of the Fixing Assembly was abnormally low.
- Solutions: 1. Check the harness/connector of the Fixing Unit. 2. Replace the Fixing Film Unit. 3. Replace the Fixing Unit. 4. Replace the Engine Controller PCB.
- Code: E004-0000
- Description: Fixing Heater drive circuit error
- Causes: A frequency failure was detected in the Fixing Assembly.
- Solutions: 1. Check the harness/connector of the Fixing Unit. 2. Replace the Fixing Film Unit. 3. Replace the Fixing Unit. 4. Replace the Engine Controller PCB.
- Code: E015-0001
- Description: Developing Disengagement error
- Causes: A developing disengagement error was detected.
- Solutions: 1. Check the harness/connector between the Developing Disengagement Solenoid and the Engine Controller PCB. 2. Check the harness/connector between the Main Motor and the Engine Controller PCB. 3. Replace the Developing Disengagement Solenoid. 4. Replace the Motor PCB. 5. Replace the Engine Controller PCB.
- Code: E066-0000
- Description: Environment Sensor error
- Causes: An error in the Environment Sensor was detected.
- Solutions: 1. Check the harness/connector between the Environment/Pickup Sensor PCB and the DC Controller PCB. 2. Replace the Environment/Pickup Sensor PCB. 3. Replace the Engine Controller PCB.
- Code: E100-0001
- Description: BD error
- Causes: BD error was detected.
- Solutions: 1. Check the harness/connector between the Laser Scanner Unit and the Engine Controller PCB. 2. Replace the Laser Scanner Unit. 3. Replace the Engine Controller PCB.
- Code: E110-0000
- Description: Error in startup of the Scanner Motor
- Causes: An error in any of the Scanner Motor, Laser Unit, or BD detection was detected at startup of the Scanner Motor.
- Solutions: 1. Check the harness/connector between the Laser Scanner Unit and the Engine Controller PCB. 2. Replace the Laser Scanner Unit. 3. Replace the Engine Controller PCB.
- Code: E110-0001
- Description: Scanner Motor rotation error
- Causes: An error in any of the Scanner motor, Laser Unit, or BD detection was detected during steady rotation of the Scanner Motor.
- Solutions: 1. Check the harness/connector between the Laser Scanner Unit and the Engine Controller PCB. 2. Replace the Laser Scanner Unit. 3. Replace the Engine Controller PCB.
- Code: E196-0001
- Description: Error in accessing the NVRAM
- Causes: Failed to access to the NVRAM.
- Solutions: 1. Replace the DC Controller PCB 2. Replace the Main Controller PCB
- Code: E196-2000
- Description: Controller communication error
- Causes: The Flash ROM in the Main Controller cannot be accessed.
- Solutions: 1. Update the set of the controller firmware. 2. Replace the Main Controller PCB.
- Code: E202-0002
- Description: HP error, failure in return
- Causes: Contact Image Sensor HP error, failure in return
- Solutions: When the same error repeatedly occurs although the power is turned OFF and then ON for several times, execute the following remedies. 1. Check the connection of Flat Cable between the Main Controller PCB and the Contact Image Sensor. 2. Replace the Flat Cable between the Main Controller PCB and the Contact Image Sensor. 3. Replace the Contact Image Sensor. 4. Replace the Main Controller PCB.
- Code: E225-0001
- Description: Light intensity of a lamp is less or equal to the criteria
- Causes: Light intensity of a lamp is less or equal to the criteria.
- Solutions: When the same error repeatedly occurs although the power is turned OFF and then ON for several times, execute the following remedies. 1. Check the connection of Flat Cable between the Main Controller PCB and the Contact Image Sensor. 2. Replace the Flat Cable between the Main Controller PCB and the Contact Image Sensor. 3. Replace the Contact Image Sensor. 4. Replace the Main Controller PCB.
- Code: E301-0001
- Description: Insufficient light intensity at shading
- Causes: Insufficient light intensity at shading.
- Solutions: When the same error repeatedly occurs although the power is turned OFF and then ON for several times, execute the following remedies. 1. Check the connection of Flat Cable between the Main Controller PCB and the Contact Image Sensor. 2. Replace the Flat Cable between the Main Controller PCB and the Contact Image Sensor. 3. Replace the Contact Image Sensor. 4. Replace the Main Controller PCB.
- Code: E733-0000
- Description: Controller communication error
- Causes: Communication error between the Main Controller PCB and the Engine Controller PCB.
- Solutions: 1. Check the connection between the Main Controller PCB and the Engine Controller PCB. 2. Update the set of the controller firmware. 3. Replace the Main Controller PCB. 4. Replace the Engine Controller Board.
- Code: E736-0000
- Description: Communication error or FAX board type error
- Causes: Communication error with CCU/modem or FAX type error when no FAX Board installed on FAX model.
- Solutions: 1. Check/replace the connection between the Main Controller PCB and the NCU PCB. 2. Update the set of the controller firmware. 3. Replace the NCU PCB. 4. Replace the Main Controller PCB.
- Code: E740-0002
- Description: Network error
- Causes: A Network Board error or an error in the Mac address was detected.
- Solutions: 1. Check the network cable connection. 2. Replace the Main Controller PCB.
- Code: E744-0002
- Description: Language file error
- Causes: The size of the language file exceeded the allowed size.
- Solutions: Update the set of the controller firmware.
- Code: E744-4000
- Description: Engine ID error
- Causes: Invalid engine connection was detected.
- Solutions: 1. Check the version of the Engine Controller PCB. 2. Update the Engine Controller PCB. 3. Update the set of the controller firmware. 4. Check the model code (because this error occurs also when the model code and the engine code are mismatched).
- Code: E744-6000
- Description: Wireless LAN communication error
- Causes: Communication error between the Main Controller PCB and the Wireless Lan PCB.
- Solutions: 1. Check the connection between the wireless LAN slot (SD-IO) and the Main Controller PCB. 2. Update the set of the controller firmware. 3. Replace the Wireless Lan PCB. 4. Replace the Main Controller PCB.
- Code: E760-0001
- Description: Main Controller PCB error
- Causes: An error occurred with the firmware of the Main Controller.
- Solutions: 1. Update the set of the controller firmware. 2. Replace the Main Controller PCB.
- Code: E806-0000
- Description: Main Fan failure
- Causes: The Main Fan Motor fails to rotate at the specified rotation speed.
- Solutions: 1. Check the harness/connector of the Main Fan. 2. Replace the Main Fan. 3. Replace the Engine Controller PCB.
- Code: E808-0000
- Description: Low Voltage Power Supply failure
- Causes: Low voltage power supply failure was detected.
- Solutions: 1. Check the harness/connector of the Low Voltage Power Supply PCB. 2. Replace the Low Voltage Power Supply Unit (which includes the Low Voltage Power Supply PCB). 3. Replace the Engine Controller PCB.
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-ipf9000s-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-c7500-driver-firmware-and-manuals/
Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html
Contact us to get support with Canon MF269dw Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
