Repair Canon LBP6030w Printer Error Codes Canon Servie Tool
– Printer model: Canon LBP6030w
– Error codes on Canon LBP6030w model and its description:
– Canon LBP6030w printer Error Codes and quick guide to troubleshooting:
- Code: E000-0000
- Description: Fixing temperature control startup error
Temperature of the Fixing Assembly did not reach the specified temperature within the specified period of time. - Solutions: 1. Check connectors on the fixing film unit. 2. Replace the fixing film unit. 3. Replace the engine controller PCB.
- Code: E001-0000
- Description: Abnormal high temperature of Fixing Assembly
Temperature of the Thermistor continuously exceeded a certain value. - Solutions: 1. Check connectors on the fixing film unit. 2. Replace the fixing film unit. 3. Replace the engine controller PCB.
- Code: E003-0000
- Description: Abnormal low temperature of Fixing Assembly
Fixing temperature was lower than the target value at printing/cleaning mode. - Solutions: 1. Check connectors on the fixing film unit. 2. Replace the fixing film unit. 3. Replace the engine controller PCB.
- Code: E004-0000
- Description: Fixing Heater drive circuit error
Abnormal frequency was detected in fixing drive circuit within the specified period of time from power-on. - Solutions: 1. Check connectors on the fixing film unit. 2. Replace the fixing film unit. 3. Replace the engine controller PCB.
- Code: E100-0000
- Description: Laser area failure
Scanner Motor control error Scanner Motor startup error BDI signal error - Solutions: 1. Check connectors on the scanner unit. 2. Replace the scanner unit. 3. Replace the engine controller PCB.
- Code: E196-0000
- Description: Error in Engine controller
A data communication error occurred in the Engine Controller PCB. - Solutions: Replace the Engine Controller PCB.
- Code: E196-2000
- Description: Error in main controller communication
Access to the Flash ROM in the Main Controller failed. - Solutions: Replace the Engine Controller PCB.
- Code: E733-0000
- Description: Printer communication error
Communication error between the Engine Controller PCB and the Main Controller PCB occurred. - Solutions: 1. Turn OFF and then ON the main power. 2. Replace the Main Controller PCB. 3. Replace the Engine Controller PCB.?
- Code: E733-0001
- Description: Printer communication error
Communication error between the Engine Controller PCB and the Main Controller PCB occurred.? - Solutions: 1. Turn OFF and then ON the main power. 2. Replace the Main Controller PCB. 3. Replace the Engine Controller PCB.
- Code: E733-0004
- Description: Printer communication error
Communication error between the Engine Controller PCB and the Main Controller PCB occurred. - Solutions: 1. Turn OFF and then ON the main power. 2. Replace the Main Controller PCB. 3. Replace the Engine Controller PCB.
- Code: E733-0005
- Description: Printer communication error
Communication error between the Engine Controller PCB and the Main Controller PCB occurred. - Solutions: 1. Turn OFF and then ON the main power. 2. Replace the Main Controller PCB. 3. Replace the Engine Controller PCB.
- Code: E733-0006
- Description: Printer communication error
Communication error between the Engine Controller PCB and the Main Controller PCB occurred. - Solutions: 1. Turn OFF and then ON the main power. 2. Replace the Main Controller PCB. 3. Replace the Engine Controller PCB.
- Code: E733-0007
- Description: Printer communication error
?Communication error between the Engine Controller PCB and the Main Controller PCB occurred. - Solutions: 1. Turn OFF and then ON the main power. 2. Replace the Main Controller PCB. 3. Replace the Engine Controller PCB.
- Code: E743-0000
- Description: Error in main controller communication
An error in reading of/writing to the Flash ROM in the Main Controller occurred. - Solutions: 1. Turn OFF and then ON the main power. 2. Replace the Main Controller PCB.
- Code: E744-4000
- Description: Engine ID error
Invalid engine connection was detected. - Solutions: 1. Turn OFF and then ON the main power. 2. Check if the installed Engine Controller PCB is for this model. 3. Replace the Engine Controller PCB.
- Code: E744-6000
- Description: Communication error with the Wireless LAN PCB
Unable to communicate with the Wireless LAN. - Solutions: 1. Turn OFF and then ON the main power. 2. Check the connection of the Wireless LAN. 3. Replace the Wireless LAN PCB. 4. Replace the Main Controller PCB.
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-ipf8300-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-sp-9880-driver-firmware-and-manuals/
Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html
Contact us to get support with Canon LBP6030w Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
