Repair Canon LBP3900 Printer Error Codes Canon Servie Tool

Repair Canon LBP3900 Printer Error Codes Canon Servie Tool

– Printer model: Canon LBP3900
– Error codes on Canon LBP3900 model and its description:

– Canon LBP3900 printer Error Codes and quick guide to troubleshooting:

• Code: E000-0
• Description: Fixing fault
• Causes: When heater temperature control is under way during initial rotation, the reading of the main thermistor fails to reach the target temperature within 80 sec. Cause The fixing film unit is faulty. The DC controller PCB is faulty.
• Solutions: – Replace the fixing film unit. – Replace the DC controller PCB.

• Code: E000-1
• Description: Fixing fault
• Causes: When the heater is on, the heater drive current level is below a specific value for as long as 5 waves of the zero-cross signal. Cause The fixing film unit is faulty. The DC controller PCB is faulty.
• Solutions: – Replace the fixing film unit. – Replace the DC controller PCB.

• Code: E001-0
• Description: Fixing error high temperature
• Causes: The reading of the main thermistor is 240 deg C or more continuously for 0.1 sec or more. Cause The main thermistor is faulty. The DC controller PCB is faulty.
• Solutions: – Replace the fixing film unit. – Replace the DC controller PCB.

• Code: E001-1
• Description: Fixing error high temperature
• Causes: The reading of the sub thermistor is 300 deg C or more continuously for 0.5 sec or more. Cause The sub thermistor is faulty. The DC controller PCB is faulty.
• Solutions: – Replace the fixing film unit. – Replace the DC controller PCB.

• Code: E003-0
• Description: Fixing low temperature
• Causes: The reading of the main thermistor fails to exceed 40 deg C within 4 sec after the start of the heater during the wait period. While heater temperature control is under way during initial rotation, the reading of the main thermistor is 70 deg C or lower continuously for 4 sec or more. While heater temperature control is under way during a standby state, the reading of the main thermistor is 50 deg C or less continuously for 0.5 or more. While heater temperature control is under way during printing, the reading of the main thermistor is 80 deg C or less continuously for 0.5 sec or more. While heater temperature control is under way during printing, the reading of the main thermistor is 40 deg C or lower than the target temperature continuously for 0.5 sec or more. The reading of any of the sub thermistors (1, 2, 3) fails to exceed 60 deg C or more within 4 sec after the start of the heater during the wait period. Cause The main thermistor is faulty. The DC controller PCB is faulty. The connector has
• Solutions: – Replace the fixing film unit. – Replace the DC controller PCB.

• Code: E003-1
• Description: Fixing low temperature
• Causes: The reading of any of the sub thermistors (1, 2, 3) fails to exceed 60 deg C within 4 sec after the start of the heater during the wait period. Cause The sub thermistor is faulty. The DC controller PCB is faulty. The connector has poor contact, or the harness is faulty.
• Solutions: – Replace the fixing film unit. – Replace the DC controller PCB.

• Code: E004-0
• Description: Fixing assembly drive assembly circuit error
• Causes: The zero-cross signal is not detected for a specific period of time or more. Cause The fixing control circuit is faulty.
• Solutions: – Replace the DC controller PCB.

• Code: E012-0
• Description: Main Motor Error
• Causes: The main motor fails to reach its normal rotation speed within 1.2 sec after it has started. Cause The main motor is faulty. The DC controller PCB is faulty.
• Solutions: – Replace the main motor. – Replace the DC controller PCB.

• Code: E012-1
• Description: Main Motor Error
• Causes: While the main motor is rotating, it fails to maintain its normal rotation speed continuously for 1.2 sec. Cause The main motor is faulty. The DC controller PCB is faulty.
• Solutions: – Replace the main motor. – Replace the DC controller PCB.

• Code: E014-0
• Description: Fixing Motor Error
• Causes: The fixing motor fails to reach its normal rotation speed within 1.2 sec after it has started. Cause The fixing motor is faulty. The DC controller PCB is faulty.
• Solutions: – Replace the fixing motor. – Replace the DC controller PCB.

• Code: E014-1
• Description: Fixing Motor Error
• Causes: The fixing motor fails to maintain its normal rotation speed continuously for 1.2 sec after its has started. Cause The fixing motor is faulty. The DC controller PCB is faulty.
• Solutions: – Replace the fixing motor. – Replace the DC controller PCB.

• Code: E015-0
• Description: Lift-up Motor Fault
• Causes: SR1 does not indicate the presence of paper when the lift-up operation is executed for 8 sec or more (i.e., the paper surface is not detected). Cause The lift-up motor is faulty. The paper feeder driver PCB is faulty. The DC controller PCB is faulty.
• Solutions: – Replace the lift-up gear. – Replace the paper feeder driver PCB. – Replace the DC controller PCB.

• Code: E100-0
• Description: Scanner Assembly Fault. The laser scanner unit is faulty. The DC controller PCB is faulty.
• Causes: BD Error While the /BD signal is being sent to the video controller, the / BDI signal is not detected at specific intervals continuously for 0.1 sec. Cause The laser scanner unit is faulty. The DC controller PCB is faulty.
• Solutions: – Replace the laser scanner unit. – Replace the DC controller PCB.

• Code: E100-1
• Description: Scanner Assembly Fault. The laser scanner unit is faulty. The DC controller PCB is faulty.
• Causes: Scanner Fault The voltage of the laser intensity output signal drops below a specific level.
• Solutions: – Replace the laser scanner unit. – Replace the DC controller PCB.

• Code: E110-0
• Description: Scanner Motor Error
• Causes: The revolution of the scanner motor does not reach 98.3% of a specific value within 4 sec after it has started.
• Solutions: – Replace the laser scanner unit.

• Code: E110-1
• Description: Scanner Motor Error
• Causes: While the scanner motor is being driven, its revolution deviates between 98.3% and 102.1% of a specific range continuously for 1 sec or more.
• Solutions: – Replace the laser scanner unit.

• Code: E805-0
• Description: Fan error
• Causes: Sub Fan Error Cause The sub fan is faulty. The DC controller PCB is faulty.
• Solutions: – Replace the sub fan. – Replace the DC controller PCB.

• Code: E805-1
• Description: Fan error
• Causes: Main Fan Error Cause The main fan is faulty. The DC controller PCB is faulty.
• Solutions: – Replace the main fan. – Replace the DC controller PCB.

• Code: E805-5
• Description: Fan error
• Causes: Duplexing Fan Error Cause The duplexing fan is faulty. The duplexing driver PCB is faulty. The DC controller PCB is faulty.
• Solutions: – Replace the duplexing fan. – Replace the duplexing driver PCB. – Replace the DC controller PCB.

• Code: E808-1
• Description: Low-Voltage Power Suplly Fault
• Causes: The low-voltage power supply PCB is faulty. The DC controller PCB.
• Solutions: – Replace the low-voltage power supply PCB. – Replace the DC controller PCB.

About Canon Servie Tool V5610

– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.

– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.

Canon Service Tool V5610 Functions

– Fix Canon printer 7 times/ 8 times red light blinking:

– Fix Canon printer error code: 5B00, 5B01, 1700, 1701

Enter Service Mode on Canon Printer

1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.

– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-ipf820-pro-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-sp-7700-driver-firmware-and-manuals/

Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html

Contact us to get support with Canon LBP3900 Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/