Repair Canon LBP2000 Printer Error Codes Canon Servie Tool
– Printer model: Canon LBP2000
– Error codes on Canon LBP2000 model and its description:
– Canon LBP2000 printer Error Codes and quick guide to troubleshooting:
- Code: 677, 6F-61
- Description: internal ROM error
- Solutions: 1 . The video controller PCB is faulty. Action: Turn off the power switch, and then turn it on. If the problem is not corrected, replace the video controller PCB.
- Code: 677, 6F-63
- Description: internal RAM error
- Solutions: 1 . The video controller PCB is faulty. Action: Turn off the power switch, and then turn it on. If the problem is not corrected, replace the video controller PCB.
- Code: 677, 6F-7A
- Description: SRAM error
- Solutions: 1 . The video controller PCB is faulty. Action: Turn off the power switch, and then turn it on. If the problem is not corrected, replace the video controller PCB.
- Code: E000
- Description: fault in fixing assembly
- Solutions: 1 . The fixing assembly is not properly mounted. Action: Turn off the power, and correct the mounting of the fixing assembly. Then, turn the power back on. 2 . The connector has poor contact. Action: Turn off the power, and check the wiring and connector from the power supply PCB/ DC controller PCB to the fixing assembly. 3 . The fixing assembly drive circuit on the power supply PCB is faulty. Action: Replace the power supply PCB. 4 . The DC controller PCB is faulty. Action: Replace the DC controller PCB.
- Code: E001
- Description: low temperature error
- Solutions: 1 . The fixing assembly is not properly mounted. Action: Turn off the power, and correct the mounting of the fixing assembly. Then, turn the power back on. 2 . The connector has poor contact. Action: Turn off the power, and check the wiring and connector from the power supply PCB/ DC controller PCB to the fixing assembly. 3 . The fixing assembly drive circuit on the power supply PCB is faulty. Action: Replace the power supply PCB. 4 . The DC controller PCB is faulty. Action: Replace the DC controller PCB.
- Code: E003
- Description: temperature error
- Solutions: 1 . The fixing assembly is not properly mounted. Action: Turn off the power, and correct the mounting of the fixing assembly. Then, turn the power back on. 2 . The connector has poor contact. Action: Turn off the power, and check the wiring and connector from the power supply PCB/ DC controller PCB to the fixing assembly. 3 . The fixing assembly drive circuit on the power supply PCB is faulty. Action: Replace the power supply PCB. 4 . The DC controller PCB is faulty. Action: Replace the DC controller PCB.
- Code: E011
- Description: main motor fault
- Solutions: 1 . The connector of the main motor (M101) drive signal has poor contact. Action: Correct the connection of the connector J903 of the main motor and the connector J106 on the DC controller PCB. 2 . The main motor (M101) is faulty. Action: Replace the main motor. 3 . The DC controller PCB is faulty. Action: Replace the DC controller PCB.
- Code: E110
- Description: scanner unit fault
- Solutions: 1 . The connector of the BD signal line has poor contact. Action: Correct the connection of the connector J908 on the BD PCB and the connector J102 on the DC controller PCB. 2 . The laser/scanner unit fault (BD) signal is not generated properly. Action: Replace the laser/scanner unit. 3 . The connector of the scanner motor (M102) drive signal line has poor contact. Action: Correct the connection of the connector J907 on the scanner driver PCB and the connector J102 on the DC controller PCB. If the fault cannot be corrected, replace the scanner unit. 4 . The DC controller PCB is faulty. Action: Replace the DC controller PCB.
- Code: E676
- Description: communication error
- Solutions: 1 . A communication error occurred between the video controller PCB and the DC controller PCB. Action: Reconnect the flexible cable between the video controller and the DC controller. If not, replace it. Then replace the DC controller PCB. If the fault cannot be corrected, replace the video controller PCB.
- Code: E805
- Description: The heat discharge fan is faulty
- Solutions: 1 . The connector of the heat discharge (FM101) drive signal line has poor contact. Action: Connect the connector J109 of the DC controller PCB correctly. 2 . The heat discharge fan (FM101) is faulty. Action: Replace the heat discharge fan. 3 . The DC controller PCB is faulty. Action: Replace the DC controller PCB.
- Code: E808
- Description: fuser drive circuit error
- Solutions: 1 . The fixing assembly is not properly mounted. Action: Turn off the power, and correct the mounting of the fixing assembly. Then, turn the power back on. 2 . The connector has poor contact. Action: Turn off the power, and check the wiring and connector from the power supply PCB/ DC controller PCB to the fixing assembly. 3 . The fixing assembly drive circuit on the power supply PCB is faulty. Action: Replace the power supply PCB. 4 . The DC controller PCB is faulty. Action: Replace the DC controller PCB.
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-cp510-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-c823632-driver-firmware-and-manuals/
Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html
Contact us to get support with Canon LBP2000 Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
