Repair Canon iPF650 Printer Error Codes Canon Servie Tool

Repair Canon iPF650 Printer Error Codes Canon Servie Tool

– Printer model: Canon iPF650
– Error codes on Canon iPF650 model and its description:

– Canon iPF650 printer Error Codes and quick guide to troubleshooting:

• Code: 03130031-4027
• Description: Lift shift timeout error A lift operation has been executed, but no sensor has been detected or a sensor has remained detected.
• Solutions: 1. Switch off the printer, then back on. 2. The carriage cannot travel to the lift drive position. 3. The lift drive cam is not engaged. 4. Faulty lift drive sensor 5. Faulty lift drive motor 6. Replace the main controller PCB.

• Code: 03xxxxxx-20xx
• Description: Media feeding error. Data mismatch error
• Solutions:

• Code: 03xxxxxx-25xx
• Description: Ink error
• Solutions:

• Code: 03xxxxxx-280x
• Description: Printhead error
• Solutions:

• Code: 03xxxxxx-281x
• Description: Maintenance cartridge error
• Solutions:

• Code: 03xxxxxx-282x
• Description: Adjustment error
• Solutions:

• Code: 03xxxxxx-2Exx
• Description: Media feeding error. Data mismatch error
• Solutions:

• Code: 03xxxxxx-2Fxx
• Description: Other errors
• Solutions:

• Code: E141-4046
• Description: Recovery part revolutions reaching 50,000 cycles or more Recovery part operations have reached a predetermined count.
• Solutions: Check the parts counter and replace required parts. (Replacement of the parts coming to the end of their useful lives is recommended.) Initialize the counter for the replacement unit mounted. The iPF5000/500/600 have a counter problem fixed. Identify the firmware version and start in download mode to upgrade the firmware to Ver.1.13 or later from any earlier release.

• Code: E144-4047
• Description: Carriage count error Supply part operations have reached a predetermined count.
• Solutions: Check the parts counter and replace the target unit or Refresh Service Kit. Initialize the parts counter for the target unit after the replacement.

• Code: E144-4048
• Description: Non-discharging nozzles on initial filling An unallowable number of nondischarging nozzles have been detected at the completion of initial filling.
• Solutions:

• Code: E144-404F
• Description: Pump revolutions full The number of HP pre-ejection pump revolution has reached the defined value.
• Solutions: Clear the counter in service mode after having replaced the HP pre-ejection tray unit.

• Code: E146-4001
• Description: Borderless/flow pre-ejection/mist recovery count full
• Solutions: Check the parts counter and replace the target unit or Refresh Service Kit. Initialize the parts counter for the target unit after the replacement.

• Code: E161-403E
• Description: Head abnormal temperature rise (printhead 1 (R), or A model) Either of the two Di sensors maintained for each printhead chip (color-specific) has been detected at 120 degrees C or higher or -10 degrees C or lower.
• Solutions:

• Code: E161-403F
• Description: Head abnormal temperature rise (printhead 2 (L)) Either of the two Di sensors maintained for each printhead chip (color-specific) has been detected at 120 degrees C or higher or -10 degrees C or lower.
• Solutions:

• Code: E161-4050
• Description: Non-ejection detection error The timing of ‘ink priming sequence’ is fallowing. -At installation of a new model printer -At reinstallation after the second transportation. -At replacement of the printhead
• Solutions:

• Code: E173-4037
• Description: Linear scale error No signal is available from the carriage encoder when the printhead is driven.
• Solutions:

• Code: E194-404A
• Description: Non-ejection count error A non-ejection part operation counter has reached a specified limit.
• Solutions: Check the parts counter and replace the target unit or Refresh Service Kit. Initialize the parts counter for the target unit after the replacement.

• Code: E196-4034
• Description: Multisensor unit version error A different version of multisensor is installed. This would not occur in an ordinary user environment.
• Solutions: Replace the multisensor unit.

• Code: E196-4040
• Description: Checksum error The checksum of a file transmitted on execution of the firmware update is unmatched.
• Solutions: 1. Start in download mode to upgrade the firmware. 2. Restart the printer in service mode to clear the error. 3. Replace the main controller PCB.

• Code: E196-4041
• Description: Flash erase error Failed to erase flash ROM on execution of the firmware update.
• Solutions: 1. Start in download mode to upgrade the firmware. 2. Restart the printer in service mode to clear the error. 3. Replace the main controller PCB.

• Code: E196-4042
• Description: Flash write error Failed to write flash ROM on execution of the firmware update.
• Solutions: 1. Start in download mode to upgrade the firmware. 2. Restart the printer in service mode to clear the error. 3. Replace the main controller PCB

• Code: E196-4043
• Description: Firmware update failure error Failed to allocate a work area on RAM on firmware update.
• Solutions: 1. Start in download mode to upgrade the firmware. 2. Restart the printer in service mode to clear the error. 3. Replace the main controller PCB.

• Code: E196-4044
• Description: EEPROM size error Size information about the firmware data transmitted on firmware update and the size of actually transmitted data do not match.
• Solutions: 1. Start in download mode to upgrade the firmware. 2. Restart the printer in service mode to clear the error. 3. Check the firmware transfer environment (IF changes, PC). 4. Replace the main controller PCB.

• Code: E196-4045
• Description: Engine EEPROM write error An EEPROM read/write failure has been detected in the engine portion of the firmware.
• Solutions: 1. Start in download mode to upgrade the firmware. 2. Restart the printer in service mode to clear the error. 3. Replace the main controller PCB.

• Code: E196-404C
• Description: Serial number information mismatch A mismatch has been detected between the serial number information stored in the EEPROM on the main controller PCB and that stored in the EEPROM on the MTC relay PCB at startup.
• Solutions: 1. Check to see if the correct PCB is mounted, since a PCB of the wrong model may have been mistakenly mounted during servicing. 2. Invoke service mode to implement PCB replacement.

• Code: E196-404D
• Description: Machine ID information mismatch A mismatch has been detected between the model ID information stored in the EEPROM on the main controller PCB and that stored in the EEPROM on the MTC relay PCB at startup.
• Solutions: 1. Check to see if the correct PCB is mounted, since a PCB of the wrong model may have been mistakenly mounted during servicing. 2. Invoke service mode to implement PCB replacement.

• Code: E196-404E
• Description: An EEPROM read/ write error has been detected in the controller portion of the firmware.
• Solutions: 1. Start in download mode to upgrade the firmware. 2. Start in service mode to clear the error. 3. Replace the main controller PCB.

• Code: E198-401C
• Description: Faulty RTC Any error other than the two errors mentioned below has been detected while initializing the RTC at startup.
• Solutions: 1. Restart the printer in service mode. 2. Replace the main controller PCB.

• Code: E198-401D
• Description: RTC low battery error A battery error has been detected while initializing the RTC at startup.
• Solutions: 1. Restart the printer in service mode. 2. Check the RTC battery. 3. Replace the main controller PCB.

• Code: E198-401E
• Description: RTC clock stop The RTC has been detected idle while initializing the RTC at startup.
• Solutions: 1. Restart the printer in service mode. 2. Replace the main controller PCB.

• Code: E199-404B
• Description: Temperature/humidity sensor error When temperature 0 and humidity 0% are detected, the detection mechanism is considered failed and an error message is displayed.
• Solutions: 1. Restart the printer in service mode to clear the error. 2. Identify the firmware version and update the firmware to the last release if it is earlier than Ver.1.31 (firmware defect). 3. Remove and reinsert the temperature/humidity sensor PCB connector 4. Replace the temperature/humidity sensor PCB.

• Code: E602-401A
• Description: HDD failure Failed to read and write to and from the HDD.
• Solutions: 1. Restart in service mode. 2. Remove and install HDD 3. Replace HDD. Switch on service mode after the replacement.

• Code: E602-401B
• Description: Poor HDD connection The HDD and the HDD controller are not indefinable.
• Solutions: 1. Restart in service mode. 2. Remove and install HDD 3. Replace HDD. Switch on service4. Replace HDD controller or the main controller PCB. Restart after the replacement.

• Code: E602-405A
• Description: Incorrect capacity HDD model is connected.
• Solutions: Replace HDD

• Code: E602-405B
• Description: Mismatched HDD model is connected.
• Solutions: Replace HDD

• Code: Exxx-40xx
• Description: Service call error
• Solutions:

• Code: W100x
• Description: Ink warning
• Solutions:

• Code: W110x
• Description: Waste ink warning
• Solutions:

• Code: x-4042
• Description: Unknown file. Check file format. Turn off printer, wait a while, then turn it on again. MIT data transfer failure Failed to write MIT data on its transmission.
• Solutions: 1. Execute ‘Initialize Paper Type’ from the system settings. (Note: All paper information will be reset to its factory defaults and additional Paper deleted.) 2. Upgrade the firmware in download mode. 3. Replace the main controller PCB.

• Code: x-4049
• Description: Unknown file. Check file format. Turn off printer, wait a while, then turn it on again. Wrong transfer ROM data model Files for a different model have been transferred on firmware update.
• Solutions: 1. Restart the printer in service mode to clear the error (this error won’t occur when FUT is used). 2. Start in download mode to upgrade the firmware. 3. Replace the main controller PCB

About Canon Servie Tool V5610

– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.

– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.

Canon Service Tool V5610 Functions

– Fix Canon printer 7 times/ 8 times red light blinking:

– Fix Canon printer error code: 5B00, 5B01, 1700, 1701

Enter Service Mode on Canon Printer

1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.

– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-mf242dw-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-sp-10600-driver-firmware-and-manuals/

Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html

Contact us to get support with Canon iPF650 Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/