Repair Canon Faxphone L100 Printer Error Codes Canon Servie Tool
– Printer model: Canon Faxphone L100
– Error codes on Canon Faxphone L100 model and its description:
– Canon Faxphone L100 printer Error Codes and quick guide to troubleshooting:
- Code: E000 0000
- Description: Startup failure
- Solutions: (1) Check the connectors of the Fixing Assembly. (J101, J1011, J552 and J702) (2) Replace the Fixing Assembly. (3) Replace the Engine Controller PCB.
- Code: E001 0000
- Description: Abnormal high temperature
- Solutions: 1) Check the connectors of the Fixing Assembly. (J101, J1011, J552 and J702) (2) Replace the Fixing Assembly. (3) Replace the Engine Controller PCB.
- Code: E003 0000
- Description: Abnormal low temperature
- Solutions: (1) Check the connectors of the Fixing Assembly. (J101, J1011, J552 and J702) (2) Replace the Fixing Assembly. (3) Replace the Engine Controller PCB.
- Code: E004 0000
- Description: Fixing heater drive circuit error
- Solutions: (1) Check the connectors of the Fixing Assembly. (J101, J1011, J552 and J702) (2) Replace the Fixing Assembly. (3) Replace the Engine Controller PCB.
- Code: E100 0001
- Description: Scanner area failure (in Scanner Motor, Laser Unit, or BD detection)
- Solutions: (1) Check the connectors of the Laser Scanner Unit. (J1, J542 J571 and J923) (2) Replace the Laser Scanner Unit. (3) Replace the Engine Controller PCB.
- Code: E196 2000
- Description: ROM read/write error (error in storing setting values in user mode/ service mode/factory mode)
- Solutions: When the same error repeatedly occurs although the power is turned OFF and then ON for several times, execute the following remedies. (1) Update the firmware of the Main Controller PCB. (2) Replace the Main Controller PCB.
- Code: E225 0001
- Description: Insufficient lamp light intensity (The light intensity is at the reference level or below.)
- Solutions: When the same error repeatedly occurs although the power is turned OFF and then ON for several times, execute the following remedies. (1) Check the connection between the Main Controller PCB and the CIS Unit. (J2) (2) Replace CIS Unit. (3) Replace the Main Controller PCB.
- Code: E225 0002
- Description: Insufficient lamp light intensity (The light intensity is partially at the reference level or below.)
- Solutions: When the same error repeatedly occurs although the power is turned OFF and then ON for several times, execute the following remedies. (1) Check the connection between the Main Controller PCB and the CIS Unit. (J2) (2) Replace CIS Unit.
- Code: E736 0000
- Description: Communication error with CCU/modem, or no FAX Board installed on FAX model
- Solutions: When the same error repeatedly occurs although the power is turned OFF and then ON for several times, execute the following remedies. (1) Replace the Main Controller PCB.
- Code: E744 0002
- Description: Language file size error
- Solutions: When the same error repeatedly occurs although the power is turned OFF and then ON for several times, execute the following remedies. Install the set of the Main controller firmware.
- Code: E744 4000
- Description: Engine ID error.(Invalid engine connection was detected.)
- Solutions: When the same error repeatedly occurs although the power is turned OFF and then ON for several times, execute the following remedies. (1) Check the Main Controller PCB. (2)Update the firmware of the Main Controller PCB. (3)Update the firmware of the Engine Controller PCB.
About Canon Servie Tool V5610
– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.
– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.
Canon Service Tool V5610 Functions
– Fix Canon printer 7 times/ 8 times red light blinking:
– Fix Canon printer error code: 5B00, 5B01, 1700, 1701
Enter Service Mode on Canon Printer
1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-mg2922-mg2900-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-nx100-driver-firmware-and-manuals/
Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html
Contact us to get support with Canon Faxphone L100 Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
