Repair Canon 1643i Printer Error Codes Canon Servie Tool

– Printer model: Canon 1643i
– Error codes on Canon 1643i model and its description:

– Canon 1643i printer Error Codes and quick guide to troubleshooting:

Code: 10-0100
Description: Toner Cartridge replacement notification alarm (K)
Causes: Detail Code: 0071 When the replacement with a genuine Toner Cartridge was detected.
Solutions:

Code: 10-0100
Description: Unidentified Toner Cartridge replacement notification alarm (K)
Causes: Detail Code: 0181 When the replacement with a non-genuine Toner Cartridge was detected.
Solutions:

Code: 10-0404
Description: Toner Cartridge empty alarm (Bk)
Causes: Alarm to be generated once the Toner Cartridge becomes empty.
Solutions:

Code: E000-0000
Description: Error in temperature rising of the Fixing Assembly
Causes: The temperature of the Fixing Assembly did not reach a certain temperature within the specified period of time.
Solutions: 1. Check the harness/connector between the Fixing Assembly and the DC Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the DC Controller PCB.

Code: E001-0000
Description: Abnormal high temperature of the Fixing Assembly
Causes: It was detected that the temperature of the Fixing Assembly was abnormally high.
Solutions: 1. Check the harness/connector between the Fixing Assembly and the DC Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the DC Controller PCB.

Code: E003-0000
Description: Abnormal low temperature of the Fixing Assembly
Causes: It was detected that the temperature of the Fixing Assembly was abnormally low.
Solutions: 1. Check the harness/connector between the Fixing Assembly and the DC Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the DC Controller PCB.

Code: E004-0000
Description: Drive circuit error
Causes: The zero cross signal was not detected for the specified period of time or more.
Solutions: 1. Check the harness/connector between the Fixing Assembly and the DC Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the DC Controller PCB.

Code: E004-0005
Description: Fixing Relay fusion error
Causes: At power ON or recovery from sleep mode, a zero cross signal was detected three times during the period of 100 ms after completion of CPU initialization.
Solutions: 1. Check the harness/connector between the Fixing Assembly and the DC Controller PCB. 2. Replace the Fixing Assembly. 3. Replace the DC Controller PCB.

Code: E014-0000
Description: Error in startup of the Main Motor
Causes: Revolution of the Main Motor did not reach the specified value.
Solutions: 1. Check the harness/connector between the Main Motor and the DC Controller PCB. 2. Replace the Main Motor. 3. Replace the DC Controller PCB.

Code: E014-0001
Description: Error in startup of the Main Motor
Causes: Revolution of the Main Motor was out of the specified range.
Solutions: 1. Check the harness/connector between the Main Motor and the DC Controller PCB. 2. Replace the Main Motor. 3. Replace the DC Controller PCB.

Code: E015-0001
Description: Cassette 1 lift-up error
Causes: After lift-up of the Lifting Plate of the cassette of the host machine started, ON status of the Paper Surface Sensor of the cassette of the host machine was not detected within the specified period of time.
Solutions: 1. Turn ON the power with the cassette of the host machine removed, insert the cassette, and then check the operation sound of the motor. When there is operation sound of the Lifter Motor, check if the Lifting Plate has been lifted up. <When the Lifting Plate has been lifted up> 1. Check the harness/connector between the DC Controller and the Paper Surface Sensor of the cassette of the host machine. 2. Replace the DC Controller PCB. <When the Lifting Plate has not been lifted up> 1. Check the condition of the gear at the host machine side (missing teeth, swing). 2. Check the harness/connector between the DC Controller and the Lifter Motor of the cassette of the host machine. 3. Replace the Main Drive Unit (included the Lifter Motor). <When there is no operation sound of the motor> 1. Check the harness/connector between the DC Controller and the Lifter Motor of the cassette of the host machine. 2. Replace the Main Drive Unit (included the Lifter Motor). 3. Replace the DC Controller PCB.

Code: E015-0002
Description: Cassette 2 lift-up error
Causes: After lift-up of the Lifting Plate of the first cassette of the Paper Feeder started, ON status of the Paper Surface Sensor of the first casstte of the Paper Feeder was not detected within the specified period of time.
Solutions: 1. Turn ON the power with the cassette of the Paper Feeder removed, insert the cassette, and then check the operation sound of the Lifter Motor. When there is operation sound of the Lifter Motor, check if the Lifting Plate has been lifted up. <When the Lifting Plate has been lifted up> 1. Check the harness/connector between the Paper Feeder Controller PCB and the Paper Surface Sensor of the Paper Feeder. 2. Replace the Paper Feeder Controller PCB. 3. Replace the DC Controller PCB. <When the Lifting Plate has not been lifted up> 1. Check the condition of the gear of the Paper Feeder (missing teeth, swing). 2. Check the harness/connector between the Paper Feeder Controller PCB and the PF Lifter mater. 3. Replace the Drive Unit (included the Lifter Motor). <When there is no operation sound of the motor> 1. Check the harness/connector between the Paper Feeder Controller PCB and the PF Lifter Motor of the Paper Feeder Unit. 2. Replace the Cassette Feeder Controller PCB. 3. Replace the DC Controller PCB.

Code: E015-0003
Description: Cassette 3 lift-up error
Causes: After lift-up of the Lifting Plate of the second cassette of the Paper Feeder started, ON status of the Paper Surface Sensor of the second casstte of the Paper Feeder was not detected within the specified period of time.
Solutions: 1. Turn ON the power with the cassette of the Paper Feeder removed, insert the cassette, and then check the operation sound of the Lifter Motor. When there is operation sound of the Lifter Motor, check if the Lifting Plate has been lifted up. <When the Lifting Plate has been lifted up> 1. Check the harness/connector between the Paper Feeder Controller PCB and the Paper Surface Sensor of the Paper Feeder. 2. Replace the Paper Feeder Controller PCB. 3. Replace the DC Controller PCB. <When the Lifting Plate has not been lifted up> 1. Check the condition of the gear of the Paper Feeder (missing teeth, swing). 2. Check the harness/connector between the Paper Feeder Controller PCB and the PF Lifter mater. 3. Replace the Drive Unit (included the Lifter Motor). <When there is no operation sound of the motor> 1. Check the harness/connector between the Paper Feeder Controller PCB and the PF Lifter Motor of the Paper Feeder Unit. 2. Replace the Cassette Feeder Controller PCB. 3. Replace the DC Controller PCB.

Code: E015-0004
Description: Cassette 4 lift-up error
Causes: After lift-up of the Lifting Plate of the third cassette of the Paper Feeder started, ON status of the Paper Surface Sensor of the third casstte of the Paper Feeder was not detected within the specified period of time.
Solutions: 1. Turn ON the power with the cassette of the Paper Feeder removed, insert the cassette, and then check the operation sound of the Lifter Motor. When there is operation sound of the Lifter Motor, check if the Lifting Plate has been lifted up. <When the Lifting Plate has been lifted up> 1. Check the harness/connector between the Paper Feeder Controller PCB and the Paper Surface Sensor of the Paper Feeder. 2. Replace the Paper Feeder Controller PCB. 3. Replace the DC Controller PCB. <When the Lifting Plate has not been lifted up> 1. Check the condition of the gear of the Paper Feeder (missing teeth, swing). 2. Check the harness/connector between the Paper Feeder Controller PCB and the PF Lifter mater. 3. Replace the Drive Unit (included the Lifter Motor). <When there is no operation sound of the motor> 1. Check the harness/connector between the Paper Feeder Controller PCB and the PF Lifter Motor of the Paper Feeder Unit. 2. Replace the Cassette Feeder Controller PCB. 3. Replace the DC Controller PCB.

Code: E066-0000
Description: Environment Sensor error
Causes: When the Environment Sensor is judged to be in error
Solutions: 1. Check the harness/connector of the High Voltage Power Supply PCB and the DC Controller PCB. 2. Replace the High Voltage Power Supply PCB (included the Environment Sensor).

Code: E110-0000
Description: Error in startup of the Scanner Motor
Causes: Scanner area error (error in the initial operation of the Scanner Motor)
Solutions: 1. Check the harness/connector between the DC Controller PCB and the Laser Scanner Unit. 2. Replace the Laser Scanner Unit (included the Scanner Motor). 3. Replace the DC Controller PCB.

Code: E110-0001
Description: Scanner Motor rotation error
Causes: Scanner area error (Scanner Motor rotation error)
Solutions: 1. Check the harness/connector between the DC Controller PCB and the Laser Scanner Unit. 2. Replace the Laser Scanner Unit (included the Scanner Motor). 3. Replace the DC Controller PCB.

Code: E196-0000
Description: DC Controller error
Causes: Update of the DC Controller failed. (RFU mode right after the startup)
Solutions: 1. Replace the DC Controller PCB.

Code: E196-1000
Description: ROM writing/reading error (Main ROM)
Causes: Error in writing/reading of main program in the Main Controller PCB (Main ROM).
Solutions: 1. Update the firmware. 2. Replace the Main Controller PCB.

Code: E196-2000
Description: ROM writing/reading error (ROM for storing setting values)
Causes: Error in writing/reading of the setting values storage area in the Main Controller PCB (ROM for storing setting values).
Solutions: 1. Update the firmware. 2. Replace the Main Controller PCB.

Code: E196-3000
Description: ROM writing/reading error (eMMC)
Causes: Unable to read/write data from the eMMC. The eMMC failure occurred.
Solutions: 1. Update the firmware. 2. Replace the Main Controller PCB.

Code: E196-3001
Description: ROM-ID mismatch (eMMC)
Causes: The eMMC has been replaced wrongly. The eMMC failure occurred.
Solutions: 1. Update the firmware. 2. Replace the Main Controller PCB.

Code: E197-0002
Description: Firmware error
Causes: Unknown engine firmware error
Solutions: 1. Turn OFF and then ON the power. 2. Update firmware. 3. Replace the DC Controller PCB.

Code: E202-0001
Description: CIS Unit HP error (outward)
Causes: The CIS Unit could not detect the home position when starting a scanning operation.
Solutions: 1. Check the harness/connector connecting from the Main Controller PCB to the CIS HP Sensor and the Reader Motor. 2. Replace the CIS HP Sensor. 3. Replace the Reader Motor. 4. Replace the CIS Unit. 5. Replace the Reader Unit. 6. Replace the Main Controller PCB.

Code: E202-0002
Description: CIS Unit HP error (homeward)
Causes: The CIS Unit could not detect the home position when completing a scanning operation.
Solutions: 1. Check the harness/connector connecting from the Main Controller PCB to the CIS HP Sensor and the Reader Motor. 2. Replace the CIS HP Sensor. 3. Replace the Reader Motor. 4. Replace the CIS Unit. 5. Replace the Reader Unit. 6. Replace the Main Controller PCB.

Code: E225-0001
Description: Light intensity of the CIS Unit below the reference level
Causes: When the light intensity is below the reference level at shading.
Solutions: 1. Disconnect and then connect the Flexible Cable. 2. Replace the Flexible Cable. 3. Replace the CIS Unit. 4. Replace the Main Controller PCB.

Code: E246-0000, E247-0000
Description: System error
Causes: System error
Solutions: Contact the sales company.

Code: E248-0001
Description: Error in access to backup data for the Reader (reading error at power-on)
Causes: The Reader-related adjustment values could not be read.
Solutions: 1. Install the set of controller firmware. 2. Replace the Main Controller PCB.

Code: E350-0000
Description: System error
Causes: System error
Solutions: Contact the sales company.

Code: E351-0000
Description: Main Controller PCB error (Scanner system)
Causes: System error
Solutions: 1. Update the firmware. 2. Replace the Main Controller PCB.

Code: E354-0000 … E355-0005
Description: System error
Causes: System error
Solutions: Contact the sales company.

Code: E719-0000
Description: Error in communication with new Card Reader (serial communication)
Causes: Unable to communicate with the new Card Reader.
Solutions: 1. Check the connection of the new Card Reader.

Code: E732-0000
Description: Scanner communication error
Causes: Scanner communication error.
Solutions: 1. Install the set of controller firmware. 2. Replace the Main Controller PCB.

Code: E733-0000
Description: Printer communication error
Causes: A communication error between the Engine Controller PCB and the Main Controller PCB occurred.
Solutions: 1. Check the harness/connector between the Engine Controller PCB and the Main Controller PCB. 2. Install the set of controller firmware. 3. Replace the Main Controller PCB. 4. Replace the Engine Controller PCB.

Code: E736-0000
Description: Fax communication error
Causes: Communication error with the CCU/modem.
Solutions: 1. Check the connection of the NCU PCB. 2. Replace the NCU PCB. 3. Replace the Main Controller PCB.

Code: E736-0001
Description: Error in ROM for backing up fax data
Causes: An error occurred in the ROM for backing up fax data.
Solutions: 1. Check the connection of the NCU PCB. 2. Replace the NCU PCB. 3. Replace the Main Controller PCB.

Code: E743-0000
Description: DDI communication error
Causes: Software sequence error
Solutions: 1. Turn OFF and then ON the power.

Code: E744-0001
Description: Invalid combination of language file versions
Causes: The language file version did not match that of the main program.
Solutions: 1. Update the firmware.

Code: E744-0002
Description: Language file error
Causes: The size of the language file exceeded the allowed size.
Solutions: 1. Update the firmware.

Code: E744-1001
Description: Version mismatch between BOOTABLE and BOOTROM
Causes: A version mismatch between the main program and the start-up program.
Solutions: 1. Update the firmware.

Code: E744-4000
Description: Invalid engine connection error
Causes: It was detected that an invalid engine was connected.
Solutions: 1. Check whether a proper Engine Controller PCB is installed. 2. Update the firmware. 3. Replace the Engine Controller PCB.

Code: E744-5000
Description: Communication error between Control Panel PCB and Main Controller PCB
Causes: Communication with the Control Panel PCB could not be established.
Solutions: 1. Check the harness/connector between the Panel PCB and the Main Controller PCB. 2. Replace the Control Panel (including the Panel PCB). 3. Replace the Main Controller PCB.

Code: E744-6000
Description: Communication error with Wireless LAN PCB
Causes: Communication with the Wireless LAN PCB could not be established.
Solutions: 1. Turn OFF and then ON the main power. 2. Check the harness/connector between the Wireless LAN PCB and the Main Controller PCB 3. Install the set of controller firmware. 4. Replace the Wireless LAN PCB. 5. Replace the Main Controller PCB.

Code: E744-7000
Description: Backup microcomputer error
Causes: An error in the microcomputer that retains fax job information of the Main Controller PCB.
Solutions: 1. Update the firmware. 2. Replace the Main Controller PCB.

Code: E746-0000
Description: Main Controller PCB error (others)
Causes: A communication error with the Main Controller PCB occurred (other than scan-related communication error).
Solutions: 1. Update the firmware. 2. Replace the Main Controller PCB.

Code: E766-8000
Description: Firmware error
Causes: Information on digital registration could not be obtained.
Solutions: 1. Install the Engine Controller firmware. 2. Install the set of controller firmware. 3. Replace the Engine Controller PCB.

Code: E766-9000
Description: Scanner power state error
Causes: Error in the power state of the Laser Scanner Unit (firmware-dependent).
Solutions: 1. Update the firmware. 2. Replace the Laser Scanner Unit.

Code: E805-0001
Description: Fan Motor 1 error
Causes: The Main Fan fails to rotate at the specified rotation speed.
Solutions: 1. Check the connection of the Main Fan. 2. Replace the Main Fan.

Code: E805-0002
Description: Fan Motor 2 error
Causes: The Sub Fan fails to rotate at the specified rotation speed.
Solutions: 1. Check the connection of the Sub Fan. 2. Replace the Sub Fan.

Code: E808-0001
Description: Low voltage power supply failure
Causes: When the printer has detected a low-voltage power supply failure
Solutions: 1. Check the harness/connector between the DC Controller PCB and the Low Voltage Power Supply PCB. 2. Replace the Low Voltage Power Supply PCB. 3. Replace the DC Controller PCB.

About Canon Servie Tool V5610

– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.

– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.

Canon Service Tool V5610 Functions

– Fix Canon printer 7 times/ 8 times red light blinking:

– Fix Canon printer error code: 5B00, 5B01, 1700, 1701

Enter Service Mode on Canon Printer

1. Turn off a printer.
2. Press and hold the Resume/Cancel/Stop button.
3. Press and hold the ON button (do not release both buttons).
4. Release the Resume/Cancel/Stop button (do not release the ON button).
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.

– Download Canon driver and firmware in specific model: https://dnasofts.com/canon-lbp6200d-printer-driver-firmware-and-user-manual-free-download/
– Download Epson driver and firmware in specific model: https://dnasofts.com/download-epson-sp-3880-driver-firmware-and-manuals/

Source:
https://chiplessprinter.com/canon-service-tool-v5610.html
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html

Contact us to get support with Canon 1643i Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/

Repair Canon 1643i Printer Error Codes Canon Servie Tool