OKI MC160 Error Codes list and solutions
– Compatible Printer model: OKI MC160
– OKI MC160 Error Code description:
- Code: 0001
- Description: Transport motor malfunction
- Causes: • The motor lock signal remains HIGH for a predetermined consecutive period of time while the transport motor remains
- Code: 001B
- Description: Developing motor malfunction
- Causes: • The developing motor does not rotate evenly even after the lapse of a given period of time while it is being started. • The motor lock signal remains HIGH for a given period of consecutive time while the developing motor is being rotated.
- Code: 0045
- Description: Exit tray cooling fan motor malfunction
- Causes: • The fan motor lock signal remains HIGH for a given period of consecutive time while the exit tray cooling fan motor is being rotated.
- Code: 004A
- Description: Duplex cooling fan motor malfunction
- Causes:
- Code: 004C
- Description: Ozone ventilation fan motor malfunction
- Causes: • The ozone ventilation fan motor does not rotate evenly even after the lapse of a given period of time while it is being started. • The motor lock signal remains HIGH for a given period of consecutive time while the ozone ventilation fan motor is being rotated.
- Code: 004E
- Description: DC power supply fan motor malfunction
- Causes: • The DC power supply fan motor does not rotate evenly even after the lapse of a given period of time while it is being started. • The motor lock signal remains HIGH for a given period of consecutive time while the DC power supply fan motor is being rotated.
- Code: 0092
- Description: Transfer belt rotation failure
- Causes: • The belt positioning sensor does not detect the transfer belt position detection hole a second time even after the lapse of a predetermined period of time after it has detected one while the transfer belt is rotated.
- Code: 0094
- Description: 2nd image transfer pressure / retraction failure
- Causes: • The 2nd image transfer retraction position sensor is not activated (retracted position) within a given period of time after the retraction sequence of the 2nd transfer roller has been started. • The 2nd image transfer retraction position sensor is not deactivated (pressed position) within a given period of time after the pressure sequence of the 2nd transfer roller has been started.
- Code: 0300
- Description: Polygon motor malfunction
- Causes: • The polygon motor does not rotate evenly even after the lapse of a given period of time after it has been started. • The motor lock signal remains HIGH for a given period of consecutive time while the polygon motor is being rotated.
- Code: 0310
- Description: Laser malfunction
- Causes: • The SOS signal is not detected within a given period of time after the output of the laser has been started.
- Code: 0500
- Description: Fuser warm-up failure
- Causes: • The thermistor /1 does not detect the specified temperature and the warm-up cycle is not completed even after the lapse of a given period of time after the cycle has been started.
- Code: 0502
- Description: Thermistor open-circuit failure
- Causes: • The temperature detected by the thermistor does not reach a predetermined level even after the lapse of a given period time after the warm-up cycle has been started.
Solve OKI MC160 Error codes
- Code: 0503
- Description: Thermistor resistance failure
- Causes: • The difference between the temperature detected by thermistor/1 and that detected by thermistor/2 exceeds a predetermined value.
- Code: 0510
- Description: Abnormally low fuser temperature
- Causes: • The temperature detected by the thermistor /1 remains lower than the specified value for a given period of time or longer.
- Code: 0520
- Description: Abnormally high fuser temperature
- Causes: • The temperature detected by the thermistor /1 remains higher than the specified value for a given period of time or longer. • The heater lamp remains ON for a given period of time or longer
- Code: 0650
- Description: Scanner home sensor abnormalities
- Causes: • A low motor lock signal is not detected even after the lapse of a predetermined period of time after the polygon motor has been started. • The motor lock signal remains HIGH for a predetermined consecutive period of time while the polygon motor remains energized.
- Code: 0F51
- Description: Waste toner full sensor malfunction
- Causes: • It is determined that the LED and photo receiver are faulty through a check made when a new imaging cartridge is detected.
- Code: 1038
- Description: Engine connect error
- Causes: • Printer control board (PRCB) to MFP board (MFPB) connection failure. • The copier determines that there is an error if the print control board (PRCB) fails to send an acknowledgement signal to the MFP board (MFPB) for a given period of time or more. • An error command signal is transmitted from the MFP board (MFPB) to printer control board (PRCB). • An error status signal is transmitted from the printer control board (PRCB) to MFP board (MFPB).
- Code: 13C0
- Description: Print control board malfunction
- Causes: • A communication error occurs in print control board (PRCB).
- Code: 13DD
- Description: Backup data error
- Causes: • The printer determines that EEPROM is yet to be mounted when the main power switch is turned ON
- Code: 13E2
- Description: Engine flash ROM write error
- Causes: • Flash ROM writing is found faulty during a check.
- Code: 13F0
- Description: Engine control failure
- Causes: • An undefined malfunction occurs in the engine section (PRCB, etc.).
- Code: 14A3
- Description: IR lamp malfunction
- Causes: • The intensity of the light emitted from the exposure lamp of the scanner falls short of the specified value.
- Code: 3C00, 3C10, 3C40
- Description: Trouble related to security
- Causes: • Contact the responsible people of KONICA MINOLTA when not returning in power switch OFF/ON.
- Code: 3FFF
- Description: Flash ROM write error
- Causes: • The copier determines that there is an error if writing to the flash ROM fails during upgrading of the firmware. • When the power switch is turned ON, the error indicator lights up steadily and a corresponding message appears on the display. • If this error message appears, no operations can then be performed. It is not possible to upgrade the firmware from a PC connected through USB connection, either.
- Code: CF01
- Description: BB error
- Causes: • Contact the responsible people of KONICA MINOLTA before taking some countermeasures. • The exit tray cooling fan motor does not rotate evenly even after the lapse of a given period of time while it is being started.
– Get more information about Epson XP 15000 troubleshooting, click here
– Get more error code list with quick guide to fix printer product, click here
– About get help with reseting Epson inkpad or others, click here
Waste Ink Pad Counter Utility Functions:
– Cleaning printhead.
– Ink charge.
– Fix Epson red lights blinking Error
– Fix Epson Service Required Error: A printer’s ink pad at the end of its service life Please contact Epson Support.
– Check the current value of waste ink counters and ink level counters.
– Clear Waste Ink Counters.
– Read and write serial number.
– Read and write USB ID.
– Read and write HEAD ID.
– Make EEPROM dump, backup.
– Paper feed test.
– Nozzle check.
– Color check pattern.
– Initialize (disable) PF deterioration offset.
– Retrieve device information
Contact us to get support with OKI MC160 Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
Or click here to get more ways.
