HP Color LaserJet CM2320 MFP error codes with quick guide

HP Color LaserJet CM2320 MFP error codes with quick guide

– Compatible Printer model: HP Color LaserJet CM2320 MFP
– HP Color LaserJet CM2320 MFP Error Codes with instructions guide:
HP Color LaserJet CM2320 MFP

• Code: –
• Display: Device error
• Description: The product has experienced a generic engine error.
• Remedy: This is a warning message only. Job output might be affected. If the error persists, perform an NVRAM initialization. If the error persists, update the firmware. If the error persists, replace the product.

• Code: –
• Display: Door open
• Description: The print-cartridge door is open.
• Remedy: Close the print-cartridge door. If the error persists, replace the print-cartridge drawer. If the error persists, replace the DC controller.

• Code: –
• Display: Engine Comm. Error
• Description: The product has experienced an engine communication timeout error.
• Remedy: Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the product to initialize. If a surge protector is being used, remove it. Plug the product directly into the wall socket. Use the power switch to turn the product on. If the error persists, verify that the connector in DC controller connector J130 is firmly seated.

• Code: –
• Display: FATAL ERROR X! CALL HP SUPPORT
• Description: An attempted firmware upgrade has failed.
• Remedy: 1. Re-download the firmware update package. 2. Install the new firmware update package. If the error persists, replace the formatter.

• Code: –
• Display: Memory is low
• Description: The product memory has been almost completely filled.
• Remedy: Press Cancel to clear the error. Break the job into smaller jobs that contain fewer pages. Turn the product off and then on to clear the memory.

• Code: –
• Display: Scanner error #
• Description: The product has experienced an error in the scanner subassembly area.
• Remedy: Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the product to initialize. If the error persists, verify that all formatter connectors are firmly connected. If the error persists, replace the scanner assembly. If the error persists, replace the formatter.

• Code: –
• Display: Scanner reserved for PC scan
• Description: A computer is using the product to create a scan.
• Remedy: Wait until the computer scan has finished, or cancel the scan from the computer software, or press Cancel .

• Code: –
• Display: Scanning error Cannot connect
• Description: The product cannot transmit scan information to a computer.
• Remedy: product off, and then turn it on. Also, turn the computer off, and then turn it on. Verify that the connection cable is not loose or damaged. Replace the cable if necessary, and try the scan again. Verify that the computer prints in order to confirm a working USB or network connection. Verify that the scan-to destination folder or software program path is correct. Remove and then reinstall the software program. If the error persists, replace the formatter.

• Code: 10.000X
• Display: 10.000X Supply Memory Error
• Description: A specific print cartridge has an e-label error. ‘X’ indicates the cartridge. • 0=black • 1=cyan • 2=magenta • 3=yellow
• Remedy: Remove and reinstall the print cartridge. Turn off and then turn on the product. If the problem is not solved, replace the cartridge.

• Code: 10.100X
• Display: 10.100X Supply Memory Error
• Description: A specific print cartridge has a faulty or missing e-label. ‘X’ indicates the cartridge. • 0=black • 1=cyan • 2=magenta • 3=yellow
• Remedy: Check the e-label. If it is broken or damaged, replace the cartridge. Verify that the cartridge is installed in the correct location. Reinstall the print cartridge. Turn off and then turn on the product. If the error is with a color cartridge, try swapping it with a different color cartridge in the tray. If the same message appears, then there is an engine problem. If a different 10.100X message appears, replace the cartridge. If the problem is not solved, replace the print-cartridge drawer. If the error persists, replace the DC controller.

• Code: 41.2
• Display: Engine error
  41.2000
• Description: The product experienced a print engine error
• Remedy: This is a warning message only. Job output might be affected. If the error persists, verify that connections J131 and J132 on the DC controller are firmly connected. If the error persists, replace the DC controller. If the error still persists, replace the product.

• Code: 49
• Display: 49 Error
• Description: The product has experienced an embedded firmware error. Under most conditions, the product will power cycle automatically.
• Remedy: Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the product to initialize. If the error persists, perform an NVRAM initialization. If the error persists, update the firmware. If the error persists, replace the formatter

• Code: 49
• Display: 49 Service Error
• Description: The product has experienced a firmware error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, perform an NVRAM initialization. If the error persists, update the firmware. If the error persists, replace the formatter

• Code: 50.1
• Display: 50.1 Fuser Error
  50.1000
• Description: The product has experienced a low fuser temperature error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, verify that the thermistor connection in the upper left of the fuser area is firmly connected. If the error persists, verify that the J150, J156, and J157 connections on the DC controller are firmly connected. If the error persists, replace the fuser.

• Code: 50.2
• Display: 50.2 Fuser Error
  50.2000
• Description: The product has experienced a slow fuser error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, verify that the fuser heat roller and pressure roller surfaces are not damaged. If the error persists, verify that the fuser motor rotates freely and that the gears are not damaged. If the error persists, replace the fuser. If the error persists, replace the DC controller

• Code: 50.3
• Display: 50.3 Fuser Error
  50.3000
• Description: The product has experienced a general fuser error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, verify that thermistor connection J706 in the upper left of the fuser area is firmly connected. If the error persists, replace the fuser. If the error persists, replace the power supply. If the error persists, replace the DC controller. If the error persists, replace the low-voltage power supply.

• Code: 50.4
• Display: 50.4 Fuser Error
  50.4000
• Description: The product has experienced a fuser drive circuit error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, verify that the fuser heat roller and pressure roller surfaces are not damaged. If the fuser is damaged, replace the fuser. If the error persists, replace the fuser motor. If the error persists, replace the power supply. If the error persists, replace the DC controller. If the error persists, replace the low-voltage power supply.

• Code: 50.7
• Display: 50.7 Fuser Error
  50.7000
• Description: The product has experienced a fuser open error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, verify that the J150, J156, and J157 connections on the DC controller are firmly connected. If the error persists, replace the fuser. If the error persists, replace the power supply. If the error persists, replace the DC controller.

• Code: 50.8
• Display: 50.8 Fuser Error
  50.8000
• Description: The product has experienced a low subthermistor fuser error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, verify that the thermistor connection in the upper left of the fuser area is firmly connected. If the error persists, replace the fuser. If the error persists, replace the DC controller.

• Code: 50.9
• Display: 50.9 Fuser Error
  50.9000
• Description: The product has experienced a high subthermistor fuser error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, verify that the thermistor connection in the upper left of the fuser area is firmly connected. If the error persists, replace the fuser. If the error persists, replace the power supply. If the error persists, replace the DC controller.

• Code: 51.XX
• Display: 51.XX Error
• Description: The product has experienced a laser scanner error. The value for XX indicates the following issues. • XX=20: Black laser scanner error • XX=21: Cyan laser scanner error • XX=22: Magenta laser scanner error • XX=23: Yellow laser scanner error
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, verify that the J131 and J132 connections on the DC controller are firmly connected. If the error persists, replace the DC controller. If the error persists, replace the product.

• Code: 52
• Display: 52 Scanner Error
• Description: The product has experienced an internal hardware error.
• Remedy: Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the product to initialize. If the error persists, replace the DC controller. If the error persists, replace the product.

• Code: 54.15
• Display: 54.15 Error
  54.1500
• Description: The product has experienced a yellow toner level sensor error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, verify that the cables between the DC controller, print-cartridge tray, and color misregistration sensor are firmly connected. If the error persists, replace the color misregistration sensor. If the error persists, replace the DC controller.

• Code: 54.16
• Display: 54.16 Error
  54.1600
• Description: The product has experienced a magenta toner level sensor error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, verify that the cables between the DC controller, print-cartridge tray, and color misregistration sensor are firmly connected. If the error persists, replace the color misregistration sensor. If the error persists, replace the DC controller.

• Code: 54.17
• Display: 54.17 Error
  54.1700
• Description: The product has experienced a cyan toner level sensor error.
• Remedy: If the error persists, verify that the cables between the DC controller, print-cartridge tray, and color misregistration sensor are firmly connected. If the error persists, replace the color misregistration sensor. If the error persists, replace the DC controller.

• Code: 54.18
• Display: 54.18 Error
  54.1800
• Description: The product has experienced a black toner level sensor error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, verify that the cables between the DC controller, print-cartridge tray, and color misregistration sensor are firmly connected. If the error persists, replace the color misregistration sensor. If the error persists, replace the DC controller.

• Code: 54.19
• Display: 54.19 Error
  54.1900
• Description: The product has experienced a top-of-page sensor error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, verify that the DC controller connectors are firmly connected. If the error persists, replace the DC controller.

• Code: 55.X
• Display: 55.X Error
• Description: The product has experienced a communication timeout error.
  The value for X indicates the following issues. • X=0: DC controller communication error • X=0601: DC controller NVRAM data error • X=0602: DC controller NVRAM access error • X=1: DC controller memory error
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, verify that the DC controller connectors are firmly connected. If the error persists, upgrade the firmware. If the error persists, replace the DC controller.

• Code: 56.01
• Display: 56.01 Error
  56.0100
• Description: The product has experienced an input tray error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Reinstall Tray 2 and, if installed, Tray 3. 3. Turn on the power and wait for the product to initialize. If the error persists, verify that the connections between the product and the tray sensor are firmly connected. If the error persists, verify that the tray flag moves correctly. If the error persists, replace the DC controller.

• Code: 57.XX
• Display: 57.XX Error
• Description: The product has experienced a problem with an internal fan.
  The value for XX indicates the following issues. • XX=01: Fan 1 (engine fan) error • XX=02: Fan 2 (duplex fan) error
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, verify that the fan rotates freely. If the error persists, replace the fan. If the error persists, replace the DC controller. If the error persists, replace the low-voltage power supply.

• Code: 59.3
• Display: 59.3 Error
  59.3000
• Description: The product has experienced a fuser motor startup error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, verify that the DC controller connectors are firmly connected. If the error persists, replace the fuser motor. If the error persists, replace the fuser. If the error persists, replace the sub-controller board. If the error persists, replace the DC controller. If the error persists, replace the low-voltage power assembly.

• Code: 59.4
• Display: 59.4 Error
  59.4000
• Description: The product has experienced a fuser motor error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, verify that the DC controller connectors are firmly connected. If the error persists, replace the fuser motor. If the error persists, replace the fuser. If the error persists, replace the sub-controller board. If the error persists, replace the DC controller. If the error persists, replace the product.

• Code: 59.70
• Display: 59.70 Error
  59.7000
• Description: The product has experienced a black developer motor startup error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, replace the developer motor. If the error persists, replace the DC controller.

• Code: 59.73
• Display: 59.73 Error
  59.7300
• Description: The product has experienced a yellow-magenta-cyan developer motor startup error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, replace the developer motor. If the error persists, replace the DC controller.

• Code: 59.80
• Display: 59.80 Error
  59.8000
• Description: The product has experienced a black developer motor rotation error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, replace the developer motor. If the error persists, replace the DC controller

• Code: 59.83
• Display: 59.83 Error
  59.8300
• Description: The product has experienced a yellow-magenta-cyan developer motor rotation error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, replace the developer motor. If the error persists, replace the DC controller.

• Code: 59.9
• Display: 59.9 Error
  59.9000
• Description: The product has experienced an ITB motor startup error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, replace the ITB. If the error persists, replace the drum motor. If the error persists, replace the DC controller.

• Code: 59.A0
• Display: 59.A0 Error
  59.0160
• Description: The product has experienced an ITB motor or main motor rotation error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, replace the ITB. If the error persists, replace the drum motor. If the error persists, replace the DC controller.

Solved HP Color LaserJet CM2320 MFP Error codes

• Code: 59.C0
• Display: 59.C0 Error
  59.0192
• Description: The product has experienced a developer motor error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, replace the developer motor. If the error persists, replace the DC controller.

• Code: 59.F0
• Display: 59.F0 Error
  59.0240
• Description: The product has experienced a transfer alienation error.
• Remedy: 1. Turn off the power by using the power switch, and then wait at least 30 seconds. 2. Turn on the power and wait for the product to initialize. If the error persists, verify that the DC controller connectors are firmly connected. If the error persists after a printcartridge replacement, examine the cartridge, and then replace it if necessary. If the error persists, replace the DC controller. If the error persists, replace the cartridge tray.

• Code: 79
• Display: 79 Error
• Description: The product has experienced an internal firmware error. Under most conditions, the product will power cycle automatically.
• Remedy: Turn off the power by using the power switch, wait at least 30 seconds, and then turn on the power and wait for the product to initialize. If the error persists, perform an NVRAM initialization. If the error persists, update the firmware. If the error persists, replace the formatter.

– Get more error code list with quick guide to fix printer product, https://nguyendangnam.com/error-code
– About get help with reseting Epson inkpad or others, https://nguyendangnam.com/reset-epson-inkpad






– Get more information about Epson XP 15000 troubleshooting, https://nguyendangnam.com/troubleshooting
– Buy cheap key of Epson WIC Reset Tool, https://shop.nguyendangnam.com/product-category/wic-reset/
– Key Epson Adjustment Program, https://shop.nguyendangnam.com/product-category/adjustment-program/
https://dnasofts.com/download-epson-xp-6100-driver-firmware-and-manuals/

Contact us to get support with HP Color LaserJet CM2320 MFP Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/

Source:
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/