Fixing Kyocera FS1035MFP Printer Error Codes in details
– Printer model: Kyocera FS1035MFP
– Fix Error codes on Kyocera FS1035MFP model and its description:
- Code: 0030
- Description: FAX control PWB system error Processing with the fax software was disabled due to a hardware problem.
- Remedy: Defective FAX control PWB. Replace the FAX control PWB.
- Code: 0070
- Description: FAX control PWB incompatible detection Error Abnormal detection of FAX control PWB incompatibility In the initial communication with the FAX control PWB, any normal communication command is not transmitted.
- Remedy: Defective fax software. Install the fax software.
Defective FAX control PWB. Replace the FAX control PWB.
- Code: 0100
- Description: Backup memory device error
- Remedy: Defective flash memory. Replace the control PWB.
Defective control PWB. Replace the control PWB.
- Code: 0120
- Description: MAC address data error
- Remedy: Defective flash memory. Replace the control PWB.
- Code: 0130
- Description: Backup memory read/write error
- Remedy: Defective flash memory. Replace the control PWB.
Defective control PWB. Replace the control PWB.
- Code: 0140
- Description: Backup memory data error
- Remedy: Defective flash memory. Replace the control PWB.
Defective control PWB. Replace the control PWB.
- Code: 0150
- Description: Control PWB EEPROM error Detecting control PWB EEPROM (U17) communication error.
- Remedy: Improper installation control PWB EEPROM (U17). Check the installation of the EEPROM (U17) and remedy if necessary.
Defective control PWB. Replace the control PWB.
Data damage of control PWB EEPROM (U17). Contact the Service Administrative Division.
- Code: 0170
- Description: Billing counting error
- Remedy: Defective control PWB. Replace the control PWB.
Data damage of control PWB EEPROM (U17). Contact the Service Administrative Division.
- Code: 0180
- Description: Machine number mismatch Machine number of main and engine does not match.
- Remedy: The main PWB or the engine PWB were exchanged. U004 Setting the machine number.
Data damage of control PWB EEPROM (U17). Contact the Service Administrative Division.
- Code: 0420
- Description: Paper feeder communication error Communication error between control PWB and optional paper feeder.
- Remedy: Improper installation paper feeder. Follow installation instruction carefully again.
Defective harness between control PWB (YC30) and paper feeder interface connector, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
Defective control PWB. Replace the control PWB.
Defective harness between PF main PWB (YC5) and paper feeder interface connector, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness (Refer to the service manual for the paper feeder).
- Code: 0830
- Description: FAX control PWB flash program area checksum error A checksum error occurred with the program of the FAX control PWB.
- Remedy: Defective fax software. Install the fax software.
Defective FAX control PWB. Replace the FAX control PWB.
- Code: 0840
- Description: Faults of RTC The time is judged to go back based on the comparison of the RTC time and the current time or five years or more have passed.
- Remedy: Defective control PWB. Replace the control PWB.
The battery is disconnected from the control PWB. Check visually and remedy if necessary.
- Code: 0870
- Description: FAX control PWB to control PWB high capacity data transfer problem High-capacity data transfer between the FAX control PWB and the control PWB of the machine was not normally performed even if the data transfer was retried the specified times.
- Remedy: Improper installation FAX control PWB. Reinstall the FAX control PWB.
Defective FAX control PWB or control PWB. Replace the FAX control PWB or control PWB and check for correct operation..
- Code: 0920
- Description: Fax file system error The backup data is not retained for file system abnormality of flash memory of the FAX control PWB.
- Remedy: Defective FAX control PWB. Replace the FAX control PWB.
- Code: 2000
- Description: Main motor error The main motor ready input is not given for 2 s during the main motor is ON.
- Remedy: Defective harness between main motor (CN1) and control PWB (YC17), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
Defective drive transmission system of the main motor. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
Defective main motor. Replace the main motor.
Defective control PWB. Replace the control PWB.
- Code: 2610
- Description: PF paper feed motor error (paper feeder) The PF paper feed motor of cassette 2 ready input is not given for 2 s during the PF paper feed motor is ON.
- Remedy: Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness (Refer to the service manual for the paper feeder).
Defective PF paper feed motor drive transmission system. Check if the gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
Defective PF main motor. Replace the PF main motor.
Defective control PWB. Replace the control PWB.
- Code: 2620
- Description: PF paper feed motor error (Paper feeder) The PF paper feed motor of cassette 3 ready input is not given for 2 s during the PF paper feed motor is ON.
- Remedy: Defective harness between PF paper feed motor and PF main PWB (YC4), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness (Refer to the service manual for the paper feeder).
Defective PF paper feed motor drive transmission system. Check if the gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
Defective PF main motor. Replace the PF main motor (Refer to the service manual for the paper feeder).
Defective control PWB. Replace the control PWB.
- Code: 3100
- Description: ISU home position error
- Remedy: Defective FFC between CCD PWB (YC1) and control PWB (YC8). Replace the image scanner unit (ISU).
Defective FFC between control PWB (YC6) and scanner PWB (YC103), or improper FFC insertion. Reinsert the FFC. Also check for continuity within the FFC. If none, remedy or replace the FFC.
Defective home position sensor. Replace the home position sensor.
Defective harness between ISU motor and scanner PWB (YC104), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
Defective ISU motor. Replace the ISU motor.
- Code: 3200
- Description: Exposure lamp error The exposure lamp is not turned on.
- Remedy: Defective FFC between scanner PWB (YC103) and control PWB (YC6), or improper FFC insertion. Reinsert the FFC. Also check for continuity within the FFC. If none, remedy or replace the FFC.
Defective FFC between CCD PWB (YC1) and control PWB (YC8). Replace the image scanner unit (ISU).
Defective harness between CCD PWB (YC3) and LED drive PWB (YC1), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
Defective harness between LED drive PWB (YC2) and exposure lamp, or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
Defective exposure lamp. Replace the exposure lamp.
Defective LED drive PWB. Replace the LED drive PWB.
Defective control PWB. Replace the control PWB.
- Code: 3300
- Description: AGC error After AGC, correct input is not obtained at CCD.
- Remedy: Defective FFC between CCD PWB (YC1) and control PWB (YC8). Replace the image scanner unit (ISU).
Defective exposure lamp. Replace the exposure lamp.
Defective CCD PWB. Replace the CCD PWB.
Defective control PWB. Replace the control PWB.
- Code: 3500
- Description: CPU – ASIC (CCD PWB) communication error An error code is detected.
- Remedy: Defective FFC between CCD PWB (YC1) and control PWB (YC8). Replace the image scanner unit (ISU).
Defective CCD PWB. Replace the CCD PWB.
Defective control PWB. Replace the control PWB.
- Code: 4000
- Description: Polygon motor (laser scanner unit) error The polygon motor ready input is not given for 6 s during the polygon motor is ON.
- Remedy: Defective harness between polygon motor and control PWB (YC10), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
Defective laser scanner unit. Replace the laser scanner unit.
Defective control PWB. Replace the control PWB.
- Code: 4200
- Description: BD error (laser scanner unit) error
- Remedy: BD sensor does not detect laser beam due to condensation on the polygon mirror. Turn machine power off for at least 30 minutes, then turn machine on again. If not cured, replace the laser scanner unit.
Defective laser scanner unit. Replace the laser scanner unit.
Defective control PWB. Replace the control PWB.
- Code: 6000
- Description: Broken Fuser heater wire The fuser temperature does not rise after the Fuser heater has been turned on.
- Remedy: Poor contact in the fuser thermistor connector terminals. Reinsert the connector.
Poor contact in the Fuser heater connector terminals. Reinsert the connector.
Fuser thermistor installed incorrectly. Replace the fuser unit.
Fuser thermal cutout triggered. Replace the fuser unit.
Fuser heater installed incorrectly. Replace the fuser unit.
Broken Fuser heater wire. Replace the fuser unit.
– Kyocera FS1035MFP printer Error Codes and quick guide to troubleshooting:
- Code: 6020
- Description: Abnormally high fuser thermistor temperature Fuser thermistor detects abnormally temperature.
- Remedy: Shorted fuser thermistor. Replace the fuser unit.
Defective control PWB. Replace the control PWB.
- Code: 6030
- Description: Broken fuser thermistor wire Input from fuser thermistor is 0 (A/D value).
- Remedy: Poor contact in the fuser thermistor connector terminals. Reinsert the connector.
Broken fuser thermistor wire. Replace the fuser unit.
Fuser thermistor installed incorrectly. Replace the fuser unit.
Fuser thermal cutout triggered. Replace the fuser unit.
Fuser heater installed incorrectly. Replace the fuser unit.
Broken Fuser heater wire. Replace the fuser unit.
- Code: 6400
- Description: Zero cross signal error The zero cross signal does not reach the control PWB for specified time.
- Remedy: Defective harness between high voltage PWB (YC202) and control PWB (YC23), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
Defective connection between power source PWB (YC103) and high voltage PWB (YC201). Reinsert the connector.
Defective power source PWB. Replace the power source PWB.
Defective control PWB. Replace the control PWB.
- Code: 7990
- Description: Waste toner full The waste toner sensor has detected that the waste toner reservoir (drum unit) is full.
- Remedy: Waste toner reservoir (drum unit) is full. Turn the power switch off/on to restart the machine. If the error is not resolved, replace the drum unit.
Defective waste toner sensor. Replace the waste toner sensor.
Defective control PWB. Replace the control PWB.
- Code: F000
- Description: Control PWB – Operation panel PWB communication error
- Remedy: Defective harness between operation panel PWB (YC1) and control PWB (YC7), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
Defective operation panel PWB. Replace the operation panel PWB.
Defective control PWB. Replace the control PWB.
- Code: F020
- Description: Control PWB RAM checksum error
- Remedy: Defective main memory (RAM) on the control PWB. Turn the power switch off/on to restart the machine. If the error is not resolved, replace control PWB.
Defective expanded memory (DIMM). Replace the expanded memory (DIMM).
- Code: F040
- Description: Control PWB engine communication error A communication error is detected.
- Remedy: Defective control PWB. Turn the power switch off/on to restart the machine. If the error is not resolved, replace control PWB.
- Code: F041
- Description: Control PWB – scanner PWB communication error A communication error is detected.
- Remedy: Defective control PWB or scanner PWB. Turn the power switch off/on to restart the machine. If the error is not resolved, replace control PWB or scanner PWB.
- Code: F050
- Description: Control PWB engine checksum error
- Remedy: Some error may have occurred when downloading the firmware of the control PWB. Download the firmware of the control PWB again.
Defective control PWB. Turn the power switch off/on to restart the machine. If the error is not resolved, replace control PWB.
- Code: F186
- Description: Control PWB video data control error
- Remedy: Defective control PWB. Turn the power switch off/on to restart the machine. If the error is not resolved, replace control PWB.
– Buy WIC Reset key on my online store: https://shop.nguyendangnam.com/product/epson-sc-f7270-wic-reset-utility-tool/
– Free Download Epson in specific model: https://dnasofts.com/download-epson-wf-4833-driver-firmware-and-manuals/
Source:
https://dnasofts.com
https://shop.nguyendangnam.com/
https://nguyendangnam.me/
https://chiplessprinter.com/reset-epson-waste-ink-pad-counter.html
Contact us to get support with Kyocera FS1035MFP Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
