Error Codes list of Riso FR Series model and quick guides
– Compatible Printer model: Riso FR Series
– Riso FR Series Error Codes with quick guides:
- Code: T1
- Description: Main Motor Lock
- Causes: • In 3 seconds from turning ON of the Main motor, the A detection sensor light path is still held blocked.
• In 8 seconds from turning ON of the Main motor, the A detection sensor is not blocked. - Troubleshooting Guides: Press <ALL RESET> key. Press <START> key.
- Code: T10
- Description: Malfunction Image Processing PCB
- Causes: • When the scanning contrast adjustment signal is not output from the image processing PCB.
- Troubleshooting Guides: OFF -> ON
- Code: T11
- Description: Pressure Control Motor Lock
- Causes: • In 100ms from turning ON of the Pressure control motor, the Encoder sensor cannot detect a pulse.
• In 5 seconds from turning ON of the Pressure control motor, the Pressure centering sensor is not turned ON/OFF. - Troubleshooting Guides: Press <ALL RESET> key.
- Code: T12
- Description: CALL SERVICE
- Causes: • Malfunction of Trimming PCB
• When the TOP signal is not output from the Trimming PCB 2 - Troubleshooting Guides: OFF -> ON
- Code: T13
- Description: Cutter Motor Lock
- Causes: • After master cutting retrial with the drum held in C-2 position, when the Master positioning sensor is in light-receiving state. (Master cutting has failed in the 2nd time.)
- Troubleshooting Guides: Drawer connector OFF (Pull out the drum.)
- Code: T14
- Description: Clamp Error (2)
- Causes: • If the actuator of the Clamp safety switch is not depressed when the Clamp solenoid is not in operation.
- Troubleshooting Guides: Press <ALL RESET> key.
- Code: T15
- Description: Flat Bed Read Pulse Motor Lock
- Causes: • If the Image scanner home position sensor does not detect the Image scanner within 18898 pulses after the Flat bed read pulse motor is activated.
• If the Image scanner ADF Shading sensor does not detect the Image scanner within 15748 pulses after the Flat bed read pulse motor is activated. • If the scanner home position sensor does not detect the Image scanner within 14,551 pulses(462 mm worth) after the Flat bed read pulse motor is activated during prescanning.
• If the Image scanner is not release from the Image scanner home position sensor within 314 pulses after the Flat bed read pulse motor is activated.
• If the Image scanner is not released from the Image scanner ADF Shading sensor within 314 pulses after the Flat bed read pulse motor is activated. - Troubleshooting Guides: Press <ALL RESET> key.
- Code: T16
- Description: Position C Sensor Malfunction
- Causes: • If the Position C sensor status has not been changed from ON to OFF (or OFF to ON) within 8 seconds from the start of the Main Motor.
- Troubleshooting Guides: Press <ALL RESET> key.
- Code: T17
- Description: Replace Battery
- Causes: • When the battery voltage is less than 2.4 V at power-on, all reset, or end of operation.
- Troubleshooting Guides: Power OFF -> ON
- Code: T18
- Description: Sorter Error
- Causes: • If an error signal is received from the sorter.
- Troubleshooting Guides: Power OFF -> ON
- Code: T19
- Description: Thermal Pressure Motor Lock
- Causes: • If the TPH Pressure switch has not been depressed within 4 seconds after the TPH Pressure motor was activated to lower the TPH.
• If the TPH Pressure switch has not been released within 4 seconds after the TPH Pressure motor was activated to raise the TPH. - Troubleshooting Guides: Press <ALL RESET> key.
- Code: T2
- Description: Elevator Motor Lock
- Causes: • In 15 seconds from turning ON of the Elevator motor in upward direction, the Elevator upper limit sensor is not pushed.
• In 15 seconds from turning ON of the Elevator motor in downward direction, the light path of the Elevator lower limit sensor is not blocked.
• In 3 seconds from turning ON of the Elevator motor in upward direction, the Elevator lower sensor is held blocked.
• In 3 seconds from turning ON of the Elevator motor in downward direction, the Elevator upper limit sensor is held pressed down. - Troubleshooting Guides: Press <ALL RESET> key.
Solve Riso FR Series Error codes
- Code: T20
- Description: Wing Motor Lock
- Causes: • If neither of the Jump wing sw1 or sw2 has been depressed within 5 seconds after the Wing motor was activated.
• If neither of the Jump wing sw1 or sw2 has been released within 5 seconds after the Wing motor was activated. - Troubleshooting Guides: Press <ALL RESET> key.
- Code: T3
- Description: Clamp Error (1)
- Causes: • In 4 seconds from turning ON of the Clamp solenoid in clamp retrial, the Clamp safety switch is held still pressed down.
• In 4 seconds from turning OFF of the Clamp solenoid, the Clamp safety SW has not been pressed.
• In 8 seconds from turning ON of the Clamp motor in opening direction in clamp retrial, the 180° Angular sensor has not detected magnet.
• In 8 seconds from turning ON of the Clamp motor in closing direction in clamp retrial, the 0° Angular sensor has not detected magnet.
In any of the above cases, master making is performed to the end. - Troubleshooting Guides: Press <ALL RESET> key. Press <START> key.
- Code: T30
- Description: P. -F. Tray Slide Pulse Motor
- Causes: • When the Paper feed tray position sensor is not turned on/ off within 165 pulses(approx. 3 second) after the P. -F. tray slide pulse motor is turned on.
- Troubleshooting Guides: Press <ALL RESET> key.
- Code: T4
- Description: Overflow
- Causes: • When ink is in contact with the Overflow sensor. The Drum set switch need be pushed.
- Troubleshooting Guides: Overflow sensor OFF <CLEAN>
- Code: T5
- Description: Print Positioning Motor Lock
- Causes: • In 12 seconds from turning ON of the Print positioning motor, the Vertical centering sensor is not turned ON/OFF.
- Troubleshooting Guides: Press <ALL RESET> key.
- Code: T50
- Description: Connect “Copy/Master” Counter
- Causes: • When the copy counter or the master counter has not been connected.
- Troubleshooting Guides: Electromagnetic counter setting signal L (Connect an electromagnetic counter.)
- Code: T6
- Description: Pressure Detection Sensor Malfunction
- Causes: • In 8 seconds from turning ON of the main motor, the Pressure detection sensor is not turned ON/OFF.
- Troubleshooting Guides: Press <ALL RESET> key.
- Code: T68
- Description: SF3000 Power Supply Malfunction
- Causes: • When no power is supplied to the SF3000.
- Troubleshooting Guides: SF3000 OK signal H(SF3000 power-on)
- Code: T7
- Description: Communication error between FR and Digitizer
- Causes: • On occurrence of an error in communication between the System PCB and Digitizer III.
- Troubleshooting Guides: OFF -> ON
- Code: T78
- Description: Machine Model Selection Error
- Causes: • When there is no machine type which corresponds to the code having been set in System PCB.
- Troubleshooting Guides: Set the switch and turn OFF and ON the power
- Code: T79
- Description: Destination Spec. Code Error
- Causes: • When the code set (DIP switch) does not match the model set with the Hex. switch.
- Troubleshooting Guides: Set the switch and turn off and on the power
- Code: T8
- Description: Communication error between System PCB and Panel PCB
- Causes: • On occurrence of an error in communication between the System PCB and the Panel PCB.
- Troubleshooting Guides: OFF -> ON
- Code: T9
- Description: Communication error between FR and the Sorters
- Causes: • On occurrence of an error in communication between the System PCB and the Sorter (TM)
- Troubleshooting Guides: OFF -> ON
– Get more information about Epson XP 15000 troubleshooting, click here
– Get more error code list with quick guide to fix printer product, click here
– About get help with reseting Epson inkpad or others, click here
Waste Ink Pad Counter Utility Functions:
– Cleaning printhead.
– Ink charge.
– Fix Epson red lights blinking Error
– Fix Epson Service Required Error: A printer’s ink pad at the end of its service life Please contact Epson Support.
– Check the current value of waste ink counters and ink level counters.
– Clear Waste Ink Counters.
– Read and write serial number.
– Read and write USB ID.
– Read and write HEAD ID.
– Make EEPROM dump, backup.
– Paper feed test.
– Nozzle check.
– Color check pattern.
– Initialize (disable) PF deterioration offset.
– Retrieve device information
Contact us to get support with Riso FR Series Error case
Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
Or click here to get more ways.
