Epson AcuLaser C1000 list error codes with quick guides

Epson AcuLaser C1000 list error codes with quick guides

– Compatible Printer model: Epson AcuLaser C1000
– Epson AcuLaser C1000 Error Codes with quick guides:

• Code: 0017
• Description: CPU Error (Undefined interrupt occurred)
• Causes:
• Troubleshooting Guides:

• Code: 0081
• Description: CPU Error (TLB correction exception)
• Causes:
• Troubleshooting Guides:

• Code: 0082
• Description: CPU Error (TLB miss exception [Load/Fetch])
• Causes:
• Troubleshooting Guides:

• Code: 0083
• Description: CPU Error (TLB miss exception [Store])
• Causes:
• Troubleshooting Guides:

• Code: 0084
• Description: CPU Error (Address Error Exception [Load/Fetch])
• Causes:
• Troubleshooting Guides:

• Code: 0085
• Description: CPU Error (Address Error Exception [Store])
• Causes:
• Troubleshooting Guides:

• Code: 0086
• Description: CPU Error (Bus Error Exception [Fetch])
• Causes:
• Troubleshooting Guides:

• Code: 0087
• Description: CPU Error (Bus Error Exception [Load/Store])
• Causes:
• Troubleshooting Guides:

• Code: 0088
• Description: CPU Error (SYSCALL Exception)
• Causes:
• Troubleshooting Guides:

• Code: 0089
• Description: CPU Error (Break Exception)
• Causes:
• Troubleshooting Guides:

• Code: 0090
• Description: CPU Error (Reserve Command Exception)
• Causes:
• Troubleshooting Guides:

• Code: 0091
• Description: CPU Error (Coprocessor Not Used Exception)
• Causes:
• Troubleshooting Guides:

• Code: 0092
• Description: CPU Error (FPU Exception)
• Causes:
• Troubleshooting Guides:

• Code: 0093
• Description: CPU Error (TLB Exception)
• Causes:
• Troubleshooting Guides:

• Code: 0094
• Description: CPU Error (XTLB Exception)
• Causes:
• Troubleshooting Guides:

• Code: 0095
• Description: CPU Error (Cache Exception)
• Causes:
• Troubleshooting Guides:

• Code: 0096
• Description: CPU Error (Trap Exception)
• Causes:
• Troubleshooting Guides:

• Code: 0097
• Description: CPU Error (FPU Exception)
• Causes:
• Troubleshooting Guides:

• Code: 0098
• Description: CPU Error (Watch Exception)
• Causes:
• Troubleshooting Guides:

• Code: 0128 … 0254
• Description: CPU Error (Undefined Trap)
• Causes:
• Troubleshooting Guides:

• Code: 0255
• Description: CPU Error (NMI Exception)
• Causes:
• Troubleshooting Guides:

• Code: 0256
• Description: CPU Error (Divide by 0)
• Causes:
• Troubleshooting Guides:

• Code: 0257
• Description: CPU Error (Computation Overflow)
• Causes:
• Troubleshooting Guides:

• Code: 0258
• Description: CPU Error (Break was generated)
• Causes:
• Troubleshooting Guides:

• Code: 0800
• Description: IPL Error (Controller defective.)
• Causes:
• Troubleshooting Guides:

• Code: 0998
• Description: Engine communication error (At power on)
• Causes:
• Troubleshooting Guides:

• Code: 0999
• Description: Engine firmware in Flash ROM is not exist.
• Causes:
• Troubleshooting Guides:

• Code: 1002
• Description: Standard RAM Error (When RAM equivalent to the standard size is not installed, etc.)
• Causes:
• Troubleshooting Guides:

• Code: 1010
• Description: Verify Error
• Causes:
• Troubleshooting Guides:

• Code: 1020
• Description: RAM Error (Slot 0)
• Causes:
• Troubleshooting Guides:

• Code: 1021
• Description: RAM Error (Slot 1)
• Causes:
• Troubleshooting Guides:

• Code: 1120
• Description: ROM Check Sum Error (bits 0-7) (Program)
• Causes:
• Troubleshooting Guides:

• Code: 1121
• Description: ROM Check Sum Error (bits 8-15) (Program)
• Causes:
• Troubleshooting Guides:

• Code: 1122
• Description: ROM Check Sum Error (bits 16-23) (Program)
• Causes:
• Troubleshooting Guides:

• Code: 1123
• Description: ROM Check Sum Error (bits 24-31) (Program)
• Causes:
• Troubleshooting Guides:

• Code: 1200
• Description: EEPROM Write Error
• Causes:
• Troubleshooting Guides:

• Code: 1210
• Description: EEPROM Write Count Limit
• Causes:
• Troubleshooting Guides:

• Code: 1400
• Description: Engine Initialization Malfunction
• Causes:
• Troubleshooting Guides:

• Code: 1500
• Description: CCNV Hardware Error
• Causes:
• Troubleshooting Guides:

• Code: 1550
• Description: Compression SRAM Initialization Hardware Error
• Causes:
• Troubleshooting Guides:

• Code: 1600
• Description: Video Related Hardware Error (including PWM IC calibration error)
• Causes:
• Troubleshooting Guides:

• Code: 1610
• Description: Video Related Hardware Error (VCNV error)
• Causes:
• Troubleshooting Guides:

Solve Epson AcuLaser C1000 Error codes

• Code: 1999
• Description: Other Hardware Error
• Causes:
• Troubleshooting Guides:

• Code: 2000
• Description: Software Error
• Causes:
• Troubleshooting Guides:

• Code: 6004
• Description: Engine board error
• Causes: Engine board
• Troubleshooting Guides:

• Code: 6008
• Description: Main motor error
• Causes: Detection of transportation motor (M1) rotation is detected 1 second after transportation motor (M1) starts rotating until the transportation motor (M1) stops. When the transportation motor M_Lock signal becomes active for 0.5 seconds, the printer detects that the transportation motor is abnormal.
• Troubleshooting Guides: 1 Does the transportation motor (M1) rotate during printing? No Remove connector PJ21A and insert it again. Yes Check that no weight applies on the each roller or gears. Others Replace PWB-A.

• Code: 6009
• Description: Fuser motor error
• Causes: Detection of fusing motor (M4) rotation is detected 1 second after fusing motor (M4) starts rotating until the fusing motor (M4) stops. When the fusing motor M_Lock signal becomes active for 0.5 seconds, the printer detects that the fusing motor is abnormal.
• Troubleshooting Guides: 1 Does the fusing motor (M4) rotate during printing? No Remove connector PJ22A and insert it again. Yes Check that no weight applies on the each roller or gears. Others Replace PWB-A.

• Code: 6011
• Description: Transfer belt fan error
• Causes: Power supply fan motor (M8) rotates by two rotational speed; full speed / half speed. When the power supply fan lock signal becomes active for 0.5 seconds, the printer detects that power supply fan motor is abnormal.
• Troubleshooting Guides: 1 At the power ON initialization sequence, does the toner absorption fan motor (M11) rotate? Check the rotation by its sound or by hand feeling wind. No Remove connector PJ30A and insert it again. Replace the fan motor. Others Replace PWB-A.

• Code: 6012
• Description: Power supply cooling fan error
• Causes:
• Troubleshooting Guides: 1 At the power ON initialization sequence, does the power supply fan motor (M8) rotate? Check the rotation by its sound or by hand feeling the wind. No Remove connector PJ16A and insert it again. Replace the power supply fan motor. Others Replace PWB-A.

• Code: 6013
• Description: Internal cooling fan error
• Causes:
• Troubleshooting Guides: 1 At the power ON initialization sequence, does the suction fan motor (M7) rotate? Check the rotation by its sound or by hand feeling wind. No Remove connector PJ3A and insert it again. Replace the fan motor. Others Replace PWB-A.

• Code: 6014
• Description: Suction fan error
• Causes: Suction fan motor (M7) rotates by two rotational speed; full speed / half speed. .. When transportation motor (M1) is rotating: Full speed .. When transportation motor (M1) is not operating: Half speed .. Cover open: Stop .. Other time: Half speed When the suction fan lock signal becomes active for 0.5 seconds, the printer detects that suction fan motor is abnormal.
• Troubleshooting Guides: 1 At the power ON initialization sequence, does the fusing fan motor (M10) rotate? Check the rotation by its sound or by hand feeling wind. No Remove connector PJ29A and insert it again. Replace the fan motor. Others Replace PWB-A.

• Code: 6015
• Description: Fuser fan error
• Causes: Fusing fan motor (M10) rotates by two rotational speed; full speed / half speed. .. When fan is booted or warm-up is completed: Full speed for 2 seconds, and then half speed .. When transportation motor (M1) is rotating: Full speed .. When warm-up is completed: Half speed .. Cover open, pause: Stop When the fusing fan lock signal becomes active for 0.5 seconds, the printer detects that fusing fan motor is abnormal.
• Troubleshooting Guides: 1 At the power ON initialization sequence, does the fusing fan motor (M10) rotate? Check the rotation by its sound or by hand feeling wind. No Remove connector PJ29A and insert it again. Replace the fan motor. Others Replace PWB-A.

• Code: 6016
• Description: Polygon motor error
• Causes: 1. When the polygon motor M_Lock signal becomes inactive for 0.4 seconds 8 seconds after the polygon motor (M6) starts driving until the polygon motor (M6) stops, the printer detects that the laser is abnormal. 2. When the LD_SOS signal is not detected for the specified time after the polygon motor is turned on and laser emission is started, the printer detects that the laser is abnormal. 3. When LD_SOS signal is not detected during the printing (during laser emission), the printer detects laser is abnormal.
• Troubleshooting Guides: 1 Check the connector on the mechanical control board of the print head and polygon motor. – Remove the connector PJ27A and insert it again. Remove the connector PJ12A and insert it again. 2 – – Replace the print head unit. Replace the laser safety switch. Others Replace PWB-A.

• Code: 6018
• Description: Laser error
• Causes: 1. When the polygon motor M_Lock signal becomes inactive for 0.4 seconds 8 seconds after the polygon motor (M6) starts driving until the polygon motor (M6) stops, the printer detects that the laser is abnormal. 2. When the LD_SOS signal is not detected for the specified time after the polygon motor is turned on and laser emission is started, the printer detects that the laser is abnormal. 3. When LD_SOS signal is not detected during the printing (during laser emission), the printer detects laser is abnormal.
• Troubleshooting Guides: 1 Check the connector on the mechanical control board of the print head and polygon motor. – Remove the connector PJ27A and insert it again. Remove the connector PJ12A and insert it again. 2 – – Replace the print head unit. Replace the laser safety switch. Others Replace PWB-A.

• Code: 6020
• Description: 2nd transfer roller gap control error
• Causes:
• Troubleshooting Guides:

• Code: 6021
• Description: Transfer Belt Cleaner gap control error
• Causes: 1. The belt cleaner pressure is detected along with the color print and special print pressure / estrangement operation. 2. When the belt cleaner estrangement sensor (PC16) does not change within the specified period after the belt cleaner motor starts rotating, it is detected that the belt cleaner is abnormal.
• Troubleshooting Guides: 1 During printing, does the belt cleaner motor rotate? (Check it by its sound.) Or remove the left cover, take a look from the front bottom and check it by the lever operation. No Remove connector PJ32A, PJ33A and insert it again. Remove connector PJ51, PJ61 and insert it again. 2 Does the sensor light shielding plate of the sensor shut the light off? No Replace the belt cleaner estrangement sensor. Others Replace PWB-A.

• Code: 6022
• Description: Transfer Belt rotation error
• Causes: 1. The transfer belt rotation is detected since the transfer belt starts rotating until the transfer belt stops. 2. While the transfer belt is rotating, if the transfer belt position sensor (PC12) does not change, it is detected that the transfer belt is abnormal.
• Troubleshooting Guides: 1 During printing, does the transfer belt rotate? (Open the front cover and check it.) No Check if the transfer belt unit is installed correctly. No Replace the transfer belt unit. Others Replace PWB-A.

• Code: 6023
• Description: Toner Cartridge rack error
• Causes:
• Troubleshooting Guides:

• Code: 6024
• Description: Heater roller heating error
• Causes: 1. When the temperature of the heat roller does not go up by the specified value for 22 to 40 seconds after warm-up is started. Same can be said for the pressure roller temperature. 2. When the temperature of the pressure roller does not reach 80°C for 90 seconds after warm-up. It is detected as abnormal pressure roller heat up. 3. When the temperature of the heat roller does not reach does not reach 170°C within 140 seconds after the temperature of pressure roller reaches 80°C after warm-boots, it detects as abnormal heat roller temperature up. 4. When the temperature of the pressure roller does not reach 130°C within 70 seconds after the temperature of the heat roller becomes more than 170°C AND when the temperature of the pressure roller does not reach 150°C within 140 seconds, it detects as the abnormal pressure roller temperature up. 5. During printing or stand-by state, when the temperature of the heat roller goes below 70°C, it detects as abnormal heat roller low temperature. Pressure roller temperature is detected as abnormal pressure roller low temperature. 6. When the temperature of the heat roller goes above 210°C during the temperature control, it detects as abnormal heat roller high temperature. Pressure roller is detected as abnormal pressure roller high temperature. 7. For heat roller, the hard shuts down at 220°C and the thermostat shuts down at 210°C. Pressure roller hard shuts down at 205°C and thermostat shuts down at 150°C.
• Troubleshooting Guides: 1 Check the connection between the fusing unit and connector. – Remove the fusing unit and install it again. 2 Does heater lamp 1 (H1) light on when turning the printer on? No Replace the fusing unit. 3 Does heater lamp 2 (H2) light on when turning the printer on? No Replace the fusing unit. Others Replace PU1 (power board). Replace PWB-A.

• Code: 6025
• Description: Heater roller low temperature error
• Causes: 1. When the temperature of the heat roller does not go up by the specified value for 22 to 40 seconds after warm-up is started. Same can be said for the pressure roller temperature. 2. When the temperature of the pressure roller does not reach 80°C for 90 seconds after warm-up. It is detected as abnormal pressure roller heat up. 3. When the temperature of the heat roller does not reach does not reach 170°C within 140 seconds after the temperature of pressure roller reaches 80°C after warm-boots, it detects as abnormal heat roller temperature up. 4. When the temperature of the pressure roller does not reach 130°C within 70 seconds after the temperature of the heat roller becomes more than 170°C AND when the temperature of the pressure roller does not reach 150°C within 140 seconds, it detects as the abnormal pressure roller temperature up. 5. During printing or stand-by state, when the temperature of the heat roller goes below 70°C, it detects as abnormal heat roller low temperature. Pressure roller temperature is detected as abnormal pressure roller low temperature. 6. When the temperature of the heat roller goes above 210°C during the temperature control, it detects as abnormal heat roller high temperature. Pressure roller is detected as abnormal pressure roller high temperature. 7. For heat roller, the hard shuts down at 220°C and the thermostat shuts down at 210°C. Pressure roller hard shuts down at 205°C and thermostat shuts down at 150°C.
• Troubleshooting Guides: 1 Check the connection between the fusing unit and connector. – Remove the fusing unit and install it again. 2 Does heater lamp 1 (H1) light on when turning the printer on? No Replace the fusing unit. 3 Does heater lamp 2 (H2) light on when turning the printer on? No Replace the fusing unit. Others Replace PU1 (power board). Replace PWB-A.

• Code: 6026
• Description: Heater roller high temperature error
• Causes: 1. When the temperature of the heat roller does not go up by the specified value for 22 to 40 seconds after warm-up is started. Same can be said for the pressure roller temperature. 2. When the temperature of the pressure roller does not reach 80°C for 90 seconds after warm-up. It is detected as abnormal pressure roller heat up. 3. When the temperature of the heat roller does not reach does not reach 170°C within 140 seconds after the temperature of pressure roller reaches 80°C after warm-boots, it detects as abnormal heat roller temperature up. 4. When the temperature of the pressure roller does not reach 130°C within 70 seconds after the temperature of the heat roller becomes more than 170°C AND when the temperature of the pressure roller does not reach 150°C within 140 seconds, it detects as the abnormal pressure roller temperature up. 5. During printing or stand-by state, when the temperature of the heat roller goes below 70°C, it detects as abnormal heat roller low temperature. Pressure roller temperature is detected as abnormal pressure roller low temperature. 6. When the temperature of the heat roller goes above 210°C during the temperature control, it detects as abnormal heat roller high temperature. Pressure roller is detected as abnormal pressure roller high temperature. 7. For heat roller, the hard shuts down at 220°C and the thermostat shuts down at 210°C. Pressure roller hard shuts down at 205°C and thermostat shuts down at 150°C.
• Troubleshooting Guides: 1 Check the connection between the fusing unit and connector. – Remove the fusing unit and install it again. 2 Does heater lamp 1 (H1) light on when turning the printer on? No Replace the fusing unit. 3 Does heater lamp 2 (H2) light on when turning the printer on? No Replace the fusing unit. Others Replace PU1 (power board). Replace PWB-A.

• Code: 6027
• Description: Heater rollers thermistor error
• Causes: 1. When the temperature of the heat roller does not go up by the specified value for 22 to 40 seconds after warm-up is started. Same can be said for the pressure roller temperature. 2. When the temperature of the pressure roller does not reach 80°C for 90 seconds after warm-up. It is detected as abnormal pressure roller heat up. 3. When the temperature of the heat roller does not reach does not reach 170°C within 140 seconds after the temperature of pressure roller reaches 80°C after warm-boots, it detects as abnormal heat roller temperature up. 4. When the temperature of the pressure roller does not reach 130°C within 70 seconds after the temperature of the heat roller becomes more than 170°C AND when the temperature of the pressure roller does not reach 150°C within 140 seconds, it detects as the abnormal pressure roller temperature up. 5. During printing or stand-by state, when the temperature of the heat roller goes below 70°C, it detects as abnormal heat roller low temperature. Pressure roller temperature is detected as abnormal pressure roller low temperature. 6. When the temperature of the heat roller goes above 210°C during the temperature control, it detects as abnormal heat roller high temperature. Pressure roller is detected as abnormal pressure roller high temperature. 7. For heat roller, the hard shuts down at 220°C and the thermostat shuts down at 210°C. Pressure roller hard shuts down at 205°C and thermostat shuts down at 150°C.
• Troubleshooting Guides: 1 Check the connection between the fusing unit and connector. – Remove the fusing unit and install it again. 2 Does heater lamp 1 (H1) light on when turning the printer on? No Replace the fusing unit. 3 Does heater lamp 2 (H2) light on when turning the printer on? No Replace the fusing unit. Others Replace PU1 (power board). Replace PWB-A.

• Code: 6028
• Description: Pressure roller heating error
• Causes: 1. When the temperature of the heat roller does not go up by the specified value for 22 to 40 seconds after warm-up is started. Same can be said for the pressure roller temperature. 2. When the temperature of the pressure roller does not reach 80°C for 90 seconds after warm-up. It is detected as abnormal pressure roller heat up. 3. When the temperature of the heat roller does not reach does not reach 170°C within 140 seconds after the temperature of pressure roller reaches 80°C after warm-boots, it detects as abnormal heat roller temperature up. 4. When the temperature of the pressure roller does not reach 130°C within 70 seconds after the temperature of the heat roller becomes more than 170°C AND when the temperature of the pressure roller does not reach 150°C within 140 seconds, it detects as the abnormal pressure roller temperature up. 5. During printing or stand-by state, when the temperature of the heat roller goes below 70°C, it detects as abnormal heat roller low temperature. Pressure roller temperature is detected as abnormal pressure roller low temperature. 6. When the temperature of the heat roller goes above 210°C during the temperature control, it detects as abnormal heat roller high temperature. Pressure roller is detected as abnormal pressure roller high temperature. 7. For heat roller, the hard shuts down at 220°C and the thermostat shuts down at 210°C. Pressure roller hard shuts down at 205°C and thermostat shuts down at 150°C.
• Troubleshooting Guides: 1 Check the connection between the fusing unit and connector. – Remove the fusing unit and install it again. 2 Does heater lamp 1 (H1) light on when turning the printer on? No Replace the fusing unit. 3 Does heater lamp 2 (H2) light on when turning the printer on? No Replace the fusing unit. Others Replace PU1 (power board). Replace PWB-A.

• Code: 6029
• Description: Pressure roller low temperature error
• Causes: 1. When the temperature of the heat roller does not go up by the specified value for 22 to 40 seconds after warm-up is started. Same can be said for the pressure roller temperature. 2. When the temperature of the pressure roller does not reach 80°C for 90 seconds after warm-up. It is detected as abnormal pressure roller heat up. 3. When the temperature of the heat roller does not reach does not reach 170°C within 140 seconds after the temperature of pressure roller reaches 80°C after warm-boots, it detects as abnormal heat roller temperature up. 4. When the temperature of the pressure roller does not reach 130°C within 70 seconds after the temperature of the heat roller becomes more than 170°C AND when the temperature of the pressure roller does not reach 150°C within 140 seconds, it detects as the abnormal pressure roller temperature up. 5. During printing or stand-by state, when the temperature of the heat roller goes below 70°C, it detects as abnormal heat roller low temperature. Pressure roller temperature is detected as abnormal pressure roller low temperature. 6. When the temperature of the heat roller goes above 210°C during the temperature control, it detects as abnormal heat roller high temperature. Pressure roller is detected as abnormal pressure roller high temperature. 7. For heat roller, the hard shuts down at 220°C and the thermostat shuts down at 210°C. Pressure roller hard shuts down at 205°C and thermostat shuts down at 150°C.
• Troubleshooting Guides: 1 Check the connection between the fusing unit and connector. – Remove the fusing unit and install it again. 2 Does heater lamp 1 (H1) light on when turning the printer on? No Replace the fusing unit. 3 Does heater lamp 2 (H2) light on when turning the printer on? No Replace the fusing unit. Others Replace PU1 (power board). Replace PWB-A.

• Code: 6030
• Description: Pressure roller high temperature error
• Causes: 1. When the temperature of the heat roller does not go up by the specified value for 22 to 40 seconds after warm-up is started. Same can be said for the pressure roller temperature. 2. When the temperature of the pressure roller does not reach 80°C for 90 seconds after warm-up. It is detected as abnormal pressure roller heat up. 3. When the temperature of the heat roller does not reach does not reach 170°C within 140 seconds after the temperature of pressure roller reaches 80°C after warm-boots, it detects as abnormal heat roller temperature up. 4. When the temperature of the pressure roller does not reach 130°C within 70 seconds after the temperature of the heat roller becomes more than 170°C AND when the temperature of the pressure roller does not reach 150°C within 140 seconds, it detects as the abnormal pressure roller temperature up. 5. During printing or stand-by state, when the temperature of the heat roller goes below 70°C, it detects as abnormal heat roller low temperature. Pressure roller temperature is detected as abnormal pressure roller low temperature. 6. When the temperature of the heat roller goes above 210°C during the temperature control, it detects as abnormal heat roller high temperature. Pressure roller is detected as abnormal pressure roller high temperature. 7. For heat roller, the hard shuts down at 220°C and the thermostat shuts down at 210°C. Pressure roller hard shuts down at 205°C and thermostat shuts down at 150°C.
• Troubleshooting Guides: 1 Check the connection between the fusing unit and connector. – Remove the fusing unit and install it again. 2 Does heater lamp 1 (H1) light on when turning the printer on? No Replace the fusing unit. 3 Does heater lamp 2 (H2) light on when turning the printer on? No Replace the fusing unit. Others Replace PU1 (power board). Replace PWB-A.

• Code: 6031
• Description: Pressure roller thermistor error
• Causes: 1. When the temperature of the heat roller does not go up by the specified value for 22 to 40 seconds after warm-up is started. Same can be said for the pressure roller temperature. 2. When the temperature of the pressure roller does not reach 80°C for 90 seconds after warm-up. It is detected as abnormal pressure roller heat up. 3. When the temperature of the heat roller does not reach does not reach 170°C within 140 seconds after the temperature of pressure roller reaches 80°C after warm-boots, it detects as abnormal heat roller temperature up. 4. When the temperature of the pressure roller does not reach 130°C within 70 seconds after the temperature of the heat roller becomes more than 170°C AND when the temperature of the pressure roller does not reach 150°C within 140 seconds, it detects as the abnormal pressure roller temperature up. 5. During printing or stand-by state, when the temperature of the heat roller goes below 70°C, it detects as abnormal heat roller low temperature. Pressure roller temperature is detected as abnormal pressure roller low temperature. 6. When the temperature of the heat roller goes above 210°C during the temperature control, it detects as abnormal heat roller high temperature. Pressure roller is detected as abnormal pressure roller high temperature. 7. For heat roller, the hard shuts down at 220°C and the thermostat shuts down at 210°C. Pressure roller hard shuts down at 205°C and thermostat shuts down at 150°C.
• Troubleshooting Guides: 1 Check the connection between the fusing unit and connector. – Remove the fusing unit and install it again. 2 Does heater lamp 1 (H1) light on when turning the printer on? No Replace the fusing unit. 3 Does heater lamp 2 (H2) light on when turning the printer on? No Replace the fusing unit. Others Replace PU1 (power board). Replace PWB-A.

• Code: 6032
• Description: Fuser roller gap control error
• Causes: 1. When the temperature of the heat roller does not go up by the specified value for 22 to 40 seconds after warm-up is started. Same can be said for the pressure roller temperature. 2. When the temperature of the pressure roller does not reach 80°C for 90 seconds after warm-up. It is detected as abnormal pressure roller heat up. 3. When the temperature of the heat roller does not reach does not reach 170°C within 140 seconds after the temperature of pressure roller reaches 80°C after warm-boots, it detects as abnormal heat roller temperature up. 4. When the temperature of the pressure roller does not reach 130°C within 70 seconds after the temperature of the heat roller becomes more than 170°C AND when the temperature of the pressure roller does not reach 150°C within 140 seconds, it detects as the abnormal pressure roller temperature up. 5. During printing or stand-by state, when the temperature of the heat roller goes below 70°C, it detects as abnormal heat roller low temperature. Pressure roller temperature is detected as abnormal pressure roller low temperature. 6. When the temperature of the heat roller goes above 210°C during the temperature control, it detects as abnormal heat roller high temperature. Pressure roller is detected as abnormal pressure roller high temperature. 7. For heat roller, the hard shuts down at 220°C and the thermostat shuts down at 210°C. Pressure roller hard shuts down at 205°C and thermostat shuts down at 150°C.
• Troubleshooting Guides: 1 Check the connection between the fusing unit and connector. – Remove the fusing unit and install it again. 2 Does heater lamp 1 (H1) light on when turning the printer on? No Replace the fusing unit. 3 Does heater lamp 2 (H2) light on when turning the printer on? No Replace the fusing unit. Others Replace PU1 (power board). Replace PWB-A.

• Code: 6033
• Description: Transparency detection sensor error
• Causes:
• Troubleshooting Guides:

• Code: 6034
• Description: Multiple manual feeder pusher error
• Causes: 1. MPT push-up tray position is detected while loading paper from the manual tray. 2. If the output of the manual tray upper position sensor (PC15) does not change even after the specified amount of time passed after the manual tray paper load solenoid (SL8) becomes ON, it is detected that the MPT push-up plate is abnormal.
• Troubleshooting Guides: Does the manual tray push paper to the paper load roller? No Arrange paper on the manual tray. 2 Does the manual tray paper load roller one-way clutch have the claws? No Replace the one-way clutch gear. Yes Replace the manual tray paper load solenoid. Others Replace PWB-A.

• Code: 6041
• Description: Main unit memory counter error
• Causes:
• Troubleshooting Guides:

• Code: 6042
• Description: Main unit memory data error
• Causes:
• Troubleshooting Guides:

• Code: 6043
• Description: Main unit memory access error
• Causes:
• Troubleshooting Guides:

– Get more error code list with quick guide to fix printer product, click here
– About get help with reseting Epson inkpad or others, click here

• Code: 6044
• Description: Main unit memory installation error
• Causes:
• Troubleshooting Guides:

• Code: 6998
• Description: Engine communication error
• Causes:
• Troubleshooting Guides:

– Get more information about Epson XP 15000 troubleshooting, click here
– Shop on my shop, click here

Contact us to get support with Epson AcuLaser C1000 Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
Or click here to get more ways.