Brother DCP1612W fix error codes list

Brother DCP1612W fix error codes list

– Compatible Printer model: Brother DCP1612W
– Brother DCP1612W Error Codes with instructions guide:

• Code: 0201
• Display: Print Unable 02 Turn the power off and then back on again.
• Description: The speed of the main motor does not stabilize within the specified time.
• Remedy: 1 Connection failure of the main motor harness Reconnect the main motor harness. 2 Connection failure of the motor encoder PCB flat cable Reconnect the motor encoder PCB flat cable. 3 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 0300
• Display: Print Unable 03 Turn the power off and then back on again.
• Description: Cannot detect the lock signal of the polygon motor for the laser unit (second time).
• Remedy: 1 Connection failure of the laser unit flat cable Reconnect the laser unit flat cable. 2 Laser unit flat cable failure Replace the laser unit flat cable. 3 Laser unit failure Replace the laser unit. 4 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 0401
• Display: Print Unable 04 Turn the power off and then back on again.
• Description: Cannot detect the synchronized signal of the polygon motor for the laser unit.
• Remedy: 1 Connection failure of the polygon motor harness Reconnect the polygon motor harness. 2 Polygon motor failure Replace the laser unit. 3 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 0501
• Display: Print Unable 05 Turn the power off and then back on again.
• Description: The center thermistor of the fuser unit has not reached the specified temperature within the specified time.
• Remedy: <User Check> • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error has reset.
  1 Connection failure of the center thermistor harness of the fuser unit Reconnect the center thermistor harness of the fuser unit. 2 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 3 Connection failure of the low voltage PCB harness Reconnect the low voltage PCB harness. 4 Fuser unit failure Replace the fuser unit. 5 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 6 Main PCB failure Replace the main PCB ASSY.

• Code: 0502
• Display: Print Unable 05 Turn the power off and then back on again.
• Description: The center thermistor has not reached the specified temperature within the specified time after the fuser unit has reached to a certain temperature.
• Remedy: <User Check> • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error has reset.
  1 Connection failure of the center thermistor harness of the fuser unit Reconnect the center thermistor harness of the fuser unit. 2 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 3 Connection failure of the low voltage PCB harness Reconnect the low voltage PCB harness. 4 Fuser unit failure Replace the fuser unit. 5 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 6 Main PCB failure Replace the main PCB ASSY.

• Code: 0503
• Display: Print Unable 05 Turn the power off and then back on again.
• Description: The center thermistor of the fuser unit detected a temperature higher than the specified value.
• Remedy: <User Check> • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error has reset.
  1 Connection failure of the center thermistor harness of the fuser unit Reconnect the center thermistor harness of the fuser unit. 2 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 3 Connection failure of the low voltage PCB harness Reconnect the low voltage PCB harness. 4 Fuser unit failure Replace the fuser unit. 5 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 6 Main PCB failure Replace the main PCB ASSY.

• Code: 0504
• Display: Print Unable 05 Turn the power off and then back on again.
• Description: After the heat unit was heated normally, the center thermistor of the fuser unit detected a temperature lower than the specified value.
• Remedy: <User Check> • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error has reset.
  1 Connection failure of the center thermistor harness of the fuser unit Reconnect the center thermistor harness of the fuser unit. 2 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 3 Connection failure of the low voltage PCB harness Reconnect the low voltage PCB harness. 4 Fuser unit failure Replace the fuser unit. 5 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 6 Main PCB failure Replace the main PCB ASSY.

• Code: 0505
• Display: Print Unable 05 Turn the power off and then back on again.
• Description: The center thermistor of the fuser unit detected a temperature rise greater than the specified value within the specified time.
• Remedy: <User Check> • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error has reset.
  1 Connection failure of the center thermistor harness of the fuser unit Reconnect the center thermistor harness of the fuser unit. 2 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 3 Connection failure of the low voltage PCB harness Reconnect the low voltage PCB harness. 4 Fuser unit failure Replace the fuser unit. 5 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 6 Main PCB failure Replace the main PCB ASSY.

• Code: 0506
• Display: Print Unable 05 Turn the power off and then back on again.
• Description: The center thermistor of the fuser unit detected a temperature fall greater than the specified value within the specified time.
• Remedy: <User Check> • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error has reset.
  1 Connection failure of the center thermistor harness of the fuser unit Reconnect the center thermistor harness of the fuser unit. 2 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 3 Connection failure of the low voltage PCB harness Reconnect the low voltage PCB harness. 4 Fuser unit failure Replace the fuser unit. 5 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 6 Main PCB failure Replace the main PCB ASSY.

• Code: 0508
• Display: Print Unable 05 Turn the power off and then back on again.
• Description: The side thermistor of the fuser unit did not reach to the specified temperature when the heater was ON.
• Remedy: <User Check> • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error has reset.
  1 Connection failure of the center thermistor harness of the fuser unit Reconnect the center thermistor harness of the fuser unit. 2 Connection failure of the side thermistor harness Reconnect the side thermistor harness of the fuser unit. 3 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 4 Connection failure of the low voltage PCB harness Reconnect the low voltage PCB harness. 5 Fuser unit failure Replace the fuser unit. 6 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 7 Main PCB failure Replace the main PCB ASSY.

• Code: 050A
• Display: Print Unable 05 Turn the power off and then back on again.
• Description: The hardware detected that the center thermistor of the fuser unit indicated a temperature error.
• Remedy: <User Check> • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error has reset.
  1 Connection failure of the center thermistor harness of the fuser unit Reconnect the center thermistor harness of the fuser unit. 2 Connection failure of the side thermistor harness Reconnect the side thermistor harness of the fuser unit. 3 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 4 Connection failure of the low voltage PCB harness Reconnect the low voltage PCB harness. 5 Fuser unit failure Replace the fuser unit. 6 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 7 Main PCB failure Replace the main PCB ASSY.

• Code: 050B
• Display: Print Unable 05 Turn the power off and then back on again.
• Description: When the temperature of the center thermistor of the fuser unit is lower than the idle temperature, the side thermistor of the fuser unit detected a temperature higher than the specified value.
• Remedy: <User Check> • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error has reset.
  1 Connection failure of the center thermistor harness of the fuser unit Reconnect the center thermistor harness of the fuser unit. 2 Connection failure of the side thermistor harness Reconnect the side thermistor harness of the fuser unit. 3 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 4 Connection failure of the low voltage PCB harness Reconnect the low voltage PCB harness. 5 Fuser unit failure Replace the fuser unit. 6 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 7 Main PCB failure Replace the main PCB ASSY.

• Code: 050C
• Display: Print Unable 05 Turn the power off and then back on again.
• Description: When the temperature of the center thermistor of the fuser unit is higher than the idle temperature, the side thermistor of the fuser unit detected a temperature lower than the specified value.
• Remedy: <User Check> • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error has reset.
  1 Connection failure of the center thermistor harness of the fuser unit Reconnect the center thermistor harness of the fuser unit. 2 Connection failure of the side thermistor harness Reconnect the side thermistor harness of the fuser unit. 3 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 4 Connection failure of the low voltage PCB harness Reconnect the low voltage PCB harness. 5 Fuser unit failure Replace the fuser unit. 6 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 7 Main PCB failure Replace the main PCB ASSY.

• Code: 050F
• Display: Print Unable 05 Turn the power off and then back on again.
• Description: Detected an unknown error in the fuser unit.
• Remedy: <User Check> • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error has reset.
  1 Connection failure of the center thermistor harness of the fuser unit Reconnect the center thermistor harness of the fuser unit. 2 Connection failure of the side thermistor harness Reconnect the side thermistor harness of the fuser unit. 3 Connection failure of the heater harness of the fuser unit Reconnect the heater harness of the fuser unit. 4 Connection failure of the low voltage PCB harness Reconnect the low voltage PCB harness. 5 Fuser unit failure Replace the fuser unit. 6 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 7 Main PCB failure Replace the main PCB ASSY.

• Code: 0900
• Display: Print Unable 09 Turn the power off and then back on again.
• Description: Detected irregular power supply more than 100 times.
• Remedy: <User Check> • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error has reset.
  1 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. Reset the irregular power supply detection counter after replacement. (Refer to “Resetting Irregular Power Supply Detection Counter”) 2 Main PCB failure Replace the main PCB ASSY.
  Note: • The irregular power supply detection error (error code: 0900) occurs when there is a large distortion in the power supply voltage supplied to the machine. In this case, if the same power supply is used, the same error may occur even when the low voltage power supply PCB unit is replaced. Ask the user to review the installation environment.

• Code: 0A02
• Display: Print Unable 0A Turn the power off and then back on again.
• Description: The fan failure was detected.
• Remedy: 1 Harness connection failure of the fan Check the harness connection of the fan and reconnect it. 2 Fan failure Replace the fan. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 0B01
• Display: Print Unable 0B Turn the power off and then back on again.
• Description: An error occurred in the high voltage power supply PCB ASSY while operating.
• Remedy: 1 Connection failure of the high voltage PCB harness Reconnect the high voltage PCB harness. 2 High voltage power supply PCB failure Replace the high voltage power supply PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 0B02
• Display: Print Unable 0B Turn the power off and then back on again.
• Description: An error occurred in the high voltage power supply PCB ASSY when the machine is in the ready state.
• Remedy: 1 Connection failure of the high voltage PCB harness Reconnect the high voltage PCB harness. 2 High voltage power supply PCB failure Replace the high voltage power supply PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 4000
• Display: Drum End Soon
• Description: The number of rotations of the drum unit is reaching the upper limit.
• Remedy: <User Check> • Prepare a new drum unit.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: 4200
• Display: Replace Drum
• Description: The number of rotations of the drum unit has reached the life limit. (Printing does not stop.)
• Remedy: <User Check> • Prepare a new drum unit.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: 4B01
• Display: Toner Low Prepare New Toner Cartridge.
• Description: Dot counter or developer roller counter of the toner is reaching the upper limit (when setting toner stop mode).
• Remedy: <User Check> • Prepare a new toner cartridge. • If the error display is not cleared after the toner cartridge has been replaced with a new one, follow the procedures below.
  1 Connection failure of the new toner sensor PCB harness Reconnect the new toner sensor PCB harness. 2 Connection failure of the motor encoder PCB flat cable Reconnect the motor encoder PCB flat cable. 3 New toner sensor PCB failure Replace the new toner sensor PCB ASSY. 4 Motor encoder PCB failure Replace the motor encoder PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 4C01
• Display: Replace Toner Open the Scanner Cover and Top Cover, replace Toner Cartridge.
• Description: Dot counter or developer roller counter of the toner has reached the upper limit (when setting toner stop mode).
• Remedy: <User Check> • Replace the toner cartridge with a new one.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: 4D01
• Display: Replace Toner Received faxes are also stored in memory until the toner cartridge is replaced or the memory is full.
• Description: Dot counter or developer roller counter of the toner is reaching the upper limit (when setting continue mode).
• Remedy: <User Check> • Prepare a new toner cartridge.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: 4E01
• Display: Toner Ended Open the Scanner Cover and Top Cover, replace Toner Cartridge.
• Description: Dot counter or developer roller counter of the toner has reached the upper limit (when setting continue mode).
• Remedy: <User Check> • Replace the toner cartridge with a new one.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: 4F01
• Display: Cartridge Error Put the Toner Cartridge back in
• Description: New toner sensor in the toner cartridge could not detect the new toner cartridge correctly.
• Remedy: 1 Main PCB failure Replace the main PCB ASSY.

• Code: 6001
• Display: Cover is Open Close the Top Cover.
• Description: The eject sensor detected that the top cover was open.
• Remedy: <User Check> • Close the top cover.
  1 Eject actuator caught in sections of the machine Reattach the eject actuator. 2 The rib inside the top cover (which presses the eject actuator) is broken Replace the top cover ASSY. 3 Eject sensor failure Replace the eject sensor PCB ASSY. 4 Paper feed/paper printing position sensor PCB failure Replace the paper feed/paper printing position sensor PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 6007
• Display: Cover is Open BD
• Description: Detected that the top cover was open by BD (beam detect sensor) in the laser unit.
• Remedy: <User Check> • Close the top cover.
  1 Connection failure of the laser unit flat cable Reconnect the laser unit flat cable. 2 The rib inside the top cover (which presses the laser shutter arm boss) is broken Replace the top cover ASSY. 3 Faulty laser shutter arm of the laser unit Replace the laser unit. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 6101
• Display: No Toner Open the Scanner Cover and Top Cover, then install the Toner Cartridge.
• Description: The new toner sensor detected that the toner cartridge was not set.
• Remedy: <User Check> • Set the toner cartridge correctly.
  1 Connection failure of the motor encoder PCB flat cable Reconnect the motor encoder PCB flat cable. 2 Connection failure of the new toner sensor PCB harness Reconnect the new toner sensor PCB harness. 3 Motor encoder PCB failure Replace the motor encoder PCB ASSY. 4 New toner sensor failure Replace the new toner sensor PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 6200
• Display: No Drum Open the Scanner Cover and Top Cover, then install the Drum Unit.
• Description: Detected that the drum unit was not set by GRID current error.
• Remedy: <User Check> • Set the drum unit correctly. • Clean the electrodes of the drum unit.
  1 Dirt on the electrodes of the drum unit Clean the electrodes of the drum unit. (Refer to the figure below.) 2 Dirt on the high voltage power supply PCB terminal Clean the high voltage power supply PCB terminal. (Refer to the figure below.) 3 Connection failure of the high voltage PCB flat cable Reconnect the high voltage PCB flat cable. 4 High voltage power supply PCB failure Replace the high voltage power supply PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 6801
• Display: Cooling Down Wait for a while
• Description: The internal temperature thermistor detected a temperature higher than the specified value.
• Remedy: <User Check> • Lower the room temperature. • Keep the machine away from heating appliances.
  1 Connection failure of the internal temperature thermistor harness Reconnect the internal temperature thermistor harness. 2 Internal temperature thermistor failure Replace the Internal temperature thermistor. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 6901
• Display: Self-Diagnostic Turn the power off, then on again. Leave the machine for 15 min.
• Description: An error occurred in the fuser unit when the power switch was turned ON or sleep mode was ended.
• Remedy: 1 Connection failure of the fuser unit harnesses Reconnect each harness of the fuser unit. 2 Fuser unit failure Replace the fuser unit. 3 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 4 Main PCB failure Replace the main PCB ASSY.
  Note: • Turn OFF the power switch. After the fuser unit has cooled sufficiently, turn ON the power switch again and leave the machine for ten minutes. This problem may then be cleared.

• Code: 6902
• Display: Self-Diagnostic Will Automatically Restart within 15 minutes.
• Description: Rechecking the error after the power switch was turned OFF and then ON again because an error was detected by the fuser unit. (This message is displayed for approximately 15 minutes when the machine is restarted after error code 6901 has occurred.)
• Remedy: 1 Connection failure of the fuser unit harnesses Reconnect each harness of the fuser unit. 2 Fuser unit failure Replace the fuser unit. 3 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 4 Main PCB failure Replace the main PCB ASSY.
  Note: • Turn OFF the power switch. After the fuser unit has cooled sufficiently, turn ON the power switch again and leave the machine for ten minutes. This problem may then be cleared.

• Code: 6A00
• Display: Drum ! Open the Scanner Cover and Top Cover and slide the green tab across the Drum Unit several times.
• Description: Detected discharge that may be attributable to dirty corona wire on the drum unit.
• Remedy: <User Check> • Slide the green tag of the drum unit left and right two or three times to clean the corona wire. • Clean the electrodes of the drum unit. • Replace the drum unit.
  1 Dirt on the electrodes of the drum unit Clean the electrodes of the drum unit. 2 Dirt on the high voltage power supply PCB terminal Clean the high voltage power supply PCB terminal. 3 Connection failure of the high voltage PCB flat cable Reconnect the high voltage PCB flat cable. 4 High voltage power supply PCB failure Replace the high voltage power supply PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 6F00
• Display: Print Unable ZC Turn the power off and then back on again.
• Description: Detected irregular power supply less than 100 times.
• Remedy: <User Check> • Turn OFF the power switch. After several seconds, turn ON the power again and check that this error is reset.
  1 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 2 Main PCB failure Replace the main PCB ASSY.

• Code: 7000
• Display: Jam Inside 1 Open the Scanner Cover and Top Cover, pull out the Drum Unit and remove the jammed paper, then press Start.
• Description: The eject sensor does not detect paper pass after the paper printing position sensor detected the paper pass.
• Remedy: <User Check> • Remove the jammed paper. • Check that the paper is set in the paper tray correctly. • Check that there is not too much paper set in the paper tray. • Flip over the paper in the paper tray or rotate the paper 180 degrees. • Check that the thickness of the paper is within the standard. • Flip through the paper and reset it in the paper tray.
  1 Foreign object inside the machine Remove the foreign object. 2 Eject actuator coming off or caught in sections of the machine Reattach the eject actuator. 3 Connection failure of the paper feed/paper printing position sensor PCB harness Reconnect the paper feed/paper printing position sensor PCB harness. 4 Connection failure of the eject sensor PCB harness Reconnect the eject sensor PCB harness. 5 Paper feed/paper printing position sensor PCB failure Replace the paper feed/paper printing position sensor PCB ASSY. 6 Eject sensor failure Replace the eject sensor PCB ASSY. 7 Main PCB failure Replace the main PCB ASSY.

• Code: 7100
• Display: Jam Inside 2 Open the Scanner Cover and remove the jammed paper, then press Start.
• Description: The eject sensor remains ON (paper pass detected) even after the paper printing position sensor detected the end of paper pass.
• Remedy: <User Check> • Remove the jammed paper. • Check that the paper is set in the paper tray correctly. • Check that there is not too much paper set in the paper tray. • Flip over the paper in the paper tray or rotate the paper 180 degrees. • Check that the thickness of the paper is within the standard. • Flip through the paper and reset it in the paper tray.
  1 Foreign object in the rear of the machine Remove the foreign object. 2 Eject actuator caught in sections of the machine Reattach the eject actuator. 3 Paper feed/paper printing position sensor PCB failure Replace the paper feed/paper printing position sensor PCB ASSY. 4 Eject sensor failure Replace the eject sensor PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 7300
• Display: Jam Tray Remove the jammed paper from Tray, then press Start.
• Description: The paper feed sensor does not detect paper pass even after the paper has been fed for the specified time.
• Remedy: <User Check> • Remove the jammed paper. • Check that the paper is set in the paper tray correctly. • Check that there is not too much paper set in the paper tray. • Flip over the paper in the paper tray or rotate the paper 180 degrees. • Check that the thickness of the paper is within the standard. • Check that the size of the paper is within the standard. • Flip through the paper and reset it in the paper tray.
  1 Foreign object in the front of the machine Remove the foreign object. 2 Gears around the plate up plate coming off Reattach gears around the plate-up plate. 3 Attachment failure of the motor drive belt Reattach the motor drive belt. 4 Attachment failure of the laser shutter arm Reattach the laser shutter arm. 5 Connection failure of the main motor harness Reconnect the main motor harness. 6 Connection failure of the motor encoder PCB flat cable Reconnect the motor encoder PCB flat cable. 7 Connection failure of the pickup solenoid harness Reconnect the pick-up solenoid harness. 8 Motor encoder PCB failure Replace the motor encoder PCB ASSY. 9 Low voltage power supply PCB failure Replace the low voltage power supply PCB unit. 10 Laser unit failure Replace the laser unit. 11 Main PCB failure Replace the main PCB ASSY.

• Code: 7D00
• Display: Jam Inside 3 Remove the jammed paper, then press Start.
• Description: When the power switch was turned ON, the eject sensor detected paper pass. (Cannot determine whether the top cover is open or whether it is a paper jam.)
• Remedy: <User Check> • Close the top cover. • Remove the jammed paper.
  1 Eject actuator caught in sections of the machine Reattach the eject actuator. 2 Paper feed/paper printing position sensor PCB failure Replace the paper feed/paper printing position sensor PCB ASSY. 3 Eject sensor failure Replace the eject sensor PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 7E00
• Display: Jam Tray Remove the jammed paper from Tray, then press Start.
• Description: Detected that multiple paper is fed five times in a row during receiving fax or printing list/ report.
• Remedy: <User Check> • Remove the jammed paper. • Check that the paper is set in the paper tray correctly. • Check that there is not too much paper set in the paper tray. • Check that the thickness of the paper is within the standard. • Check that the size of the paper is within the standard. • Flip through the paper and reset it in the paper tray.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: 8E01
• Display: Size mismatch Fax received. Set correct paper size in menu.
• Description: Upon fax reception, the paper size setting is the one other than A4, Letter.
• Remedy: <User Check> • Select A4 or letter size in the paper setting.
  1 Paper printing position actuator caught in sections of the machine Reattach the paper printing position actuator. 2 Paper feed/paper printing position sensor failure Replace the paper feed/paper printing position sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 8E02
• Display: Size mismatch Reload correct paper, then press Start.
• Description: Detected that the size of paper set in the paper tray was over 10 mm shorter than letter size during receiving fax or printing list/report.
• Remedy: <User Check> • Select A4 or letter size in the paper setting.
  1 Paper printing position actuator caught in sections of the machine Reattach the paper printing position actuator. 2 Paper feed/paper printing position sensor failure Replace the paper feed/paper printing position sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 9002
• Display: Size Mismatch Reload correct paper, then press Start.
• Description: When printing from the paper tray, the size of paper set in the paper tray does not match the size specified by the driver.
• Remedy: <User Check> • Change the driver setting to match the size of the paper set in the paper tray.
  1 Paper printing position actuator caught in sections of the machine Reattach the paper printing position actuator. 2 Paper feed/paper printing position sensor failure Replace the paper feed/paper printing position sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 9302
• Display: No Paper Load paper, then press Start.
• Description: When printing from the paper tray, the paper feed sensor detected that there was no paper set in the paper tray.
• Remedy: <User Check> • Remove the jammed paper. • Check that the paper is set in the paper tray correctly. • Check that there is not too much paper set in the paper tray. • Check that the thickness of the paper is within the standard. • Check that the size of the paper is within the standard. • Flip through the paper and reset it in the paper tray.
  1 Foreign object in the pick-up roller. Remove the foreign object. 2 Connection failure of the paper feed/paper printing position sensor PCB harness Reconnect the paper feed/paper printing position sensor PCB harness. 3 Paper feed actuator L/R caught in sections of the machine Reattach the paper feed actuator L/R. 4 Paper feed sensor failure Replace the paper feed/paper printing position sensor PCB ASSY. 5 Main PCB failure Replace the main PCB ASSY.

• Code: 9307
• Display: No Paper Load paper, then press Start.
• Description: Detected that paper has run out during receiving fax or printing list/report.
• Remedy: <User Check> • Set paper in the paper tray.
  1 Connection failure of the paper feed/paper printing position sensor PCB harness Reconnect the paper feed/paper printing position sensor PCB harness. 2 Paper feed actuator L/R coming off Reattach the paper feed actuator L/R. 3 Paper feed sensor failure Replace the paper feed/paper printing position sensor PCB ASSY. 4 Main PCB failure Replace the main PCB ASSY.

• Code: 9601
• Display: Wrong Paper Type Reload with A4, Letter, Legal or Folio paper, and press Start.
• Description: The paper feed sensor detected that the paper width was narrower than A4 size.
• Remedy: <User Check> • Set A4/letter size paper or bigger.
  1 Paper feed actuator L/R coming off Reattach the paper feed actuator L/R. 2 Paper feed sensor failure Replace the paper feed/paper printing position sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: 9608
• Display: Wrong Paper Type Reload with A4, Letter, Legal or Folio paper, and press Start.
• Description: The paper feed sensor detected that the paper length was shorter than the specified size.
• Remedy: <User Check> • Set A4/letter size paper or bigger.
  1 Paper feed actuator L/R coming off Reattach the paper feed actuator L/R. 2 Paper feed sensor failure Replace the paper feed/paper printing position sensor PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: A200
• Display: Document Jam Clear the scanner jam, then press the Stop Key.
• Description: The document scanning position sensor detected that the document length was 90 cm or more while scanning a document.
• Remedy: <User Check> • Use A4 size paper or smaller. • Remove the jammed document.
  1 Document scanning position actuator caught in sections of the machine Reattach the document scanning position actuator. 2 Document scanning position sensor failure Replace the ADF unit. 3 Main PCB failure Replace the main PCB ASSY.

• Code: A300
• Display: Document Jam Clear the scanner jam, then press the Stop Key.
• Description: The document scanning position sensor has not detected the document passing even after the document has been fed for the specified distance.
• Remedy: <User Check> • Remove the jammed document.
  1 Document scanning position actuator coming off Reattach the document scanning position actuator. 2 Document scanning position sensor failure Replace the ADF unit. 3 Main PCB failure Replace the main PCB ASSY.

Solved Brother DCP1612W Error codes

• Code: A500
• Display: Scan Unable Remove the original document. Turn the power off, then on again
• Description: When scanning the fax, white or black correction data for the CIS was not within the correct range.
• Remedy: 1 Incorrect correction data for CIS unit Execute function code 55. 2 Connection failure of the CIS flat cable Reconnect the CIS flat cable. 3 CIS unit failure Replace the CIS unit. 4 Main PCB failure Replace the main PCB ASSY.

• Code: A600
• Display: Scan Unable A6 Turn the power off and then back on again.
• Description: Although operation was retried due to error A500 that occurred while scanning the fax, white or black correction data for the CIS was not within the correct range.
• Remedy: 1 Incorrect correction data for CIS unit Execute function code 55. 2 Connection failure of the CIS flat cable Reconnect the CIS flat cable. 3 CIS unit failure Replace the CIS unit. 4 Main PCB failure Replace the main PCB ASSY.

• Code: A700
• Display: Print Unable A7 Turn the power off and then back on again.
• Description: Color parameter in the ROM does not match the CIS.
• Remedy: 1 Incorrect correction data for CIS unit Execute function code 55. 2 Connection failure of the CIS flat cable Reconnect the CIS flat cable. 3 CIS unit failure Replace the CIS unit. 4 Main PCB failure Replace the main PCB ASSY.

• Code: A800
• Display: Print Unable See Troubleshooting and routine maintenance chapter in User’s Guide.
• Description: An error was detected in the color parameter in the ROM during scanned image processing.
• Remedy: 1 Incorrect correction data for CIS unit Execute function code 55. 2 Connection failure of the CIS flat cable Reconnect the CIS flat cable. 3 CIS unit failure Replace the CIS unit. 4 Main PCB failure Replace the main PCB ASSY.

• Code: AD00
• Display: Scan Unable Remove the original document. Turn the power off, then on again
• Description: Image processing cannot be completed correctly because the number of pixels required for image processing is insufficient in the scanned data.
• Remedy: 1 Incorrect correction data for CIS unit Execute function code 55. 2 Connection failure of the CIS flat cable Reconnect the CIS flat cable. 3 CIS unit failure Replace the CIS unit. 4 Main PCB failure Replace the main PCB ASSY.

• Code: AF00
• Display: Scan Unable AF Turn the power off and then back on again.
• Description: Home position is still being detected even after the CIS was moved.
• Remedy: 1 Dust on the CIS rail Remove the dust on the CIS rail. 2 CIS drive belt coming off Reattach the CIS drive belt. 3 Connection failure of the document scanner motor harness Reconnect the document scanner motor harness. 4 CIS unit failure Replace the CIS unit. 5 Document scanner motor failure Replace the document scanner unit. 6 Main PCB failure Replace the main PCB ASSY.

• Code: B000
• Display: SCANNER ERROR FB/SCANNER ERROR ADF
• Description: Detected that the CIS flat cable is not connected.
• Remedy: 1 Connection failure of the CIS harness Reconnect the CIS harness. 2 CIS unit failure Replace the CIS unit. 3 Main PCB failure Replace the main PCB ASSY.

• Code: B900
• Display: Scanner Error
• Description: The white level does not increase during scanning although the light intensity was increased.
• Remedy: 1 CIS unit failure Replace the CIS unit. 2 Dirt on the white tape Replace the scanner unit. 3 Main PCB failure Replace the main PCB ASSY.

• Code: BA00
• Display: Scanner Error
• Description: CIS received an external light from somewhere other than the CIS during scanning.
• Remedy: <User Check> • Check that the light is not applied directly to the scanner unit. • Close the scanner cover.
  1 CIS unit failure Replace the CIS unit. 2 Damaged ADF unit Replace the ADF unit. 3 Damaged scanner unit Replace the scanner unit. 4 Main PCB failure Replace the main PCB ASSY.

• Code: BB00
• Display: Scanner Error
• Description: A white level not within the standard was scanned when function code 55 was executed.
• Remedy: 1 CIS unit failure Replace the CIS unit. 2 Main PCB failure Replace the main PCB ASSY.

• Code: BD00
• Display: Scanner Error
• Description: A black level not within the standard was scanned when function code 55 was executed.
• Remedy: <User Check> • Remove the paper jammed inside the machine.
  1 CIS unit failure Replace the CIS unit. 2 Main PCB failure Replace the main PCB ASSY.

• Code: C700
• Display: Out of Memory Press Stop Key
• Description: There is insufficient memory to expand PC print data.
• Remedy: <User Check> • Print the print data stored in the memory. • Divide the print data and print them separately.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: D100
• Display: Print Unable D1 Turn the power off and then back on again.
• Description: An error occurred while initializing the modem.
• Remedy: 1 Connection failure of the modem PCB flat cable Reconnect the modem PCB flat cable. 2 Modem PCB failure Replace the modem PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: D200
• Display: Machine Error Unplug machine, then call Brother.
• Description: Detected that the modem PCB is not connected.
• Remedy: 1 Connection failure of the modem PCB flat cable Reconnect the modem PCB flat cable. 2 Modem PCB failure Replace the modem PCB ASSY. 3 Main PCB failure Replace the main PCB ASSY.

• Code: E000
• Display: Print Unable E0 Turn the power off and then back on again.
• Description: An error occurred in the ROM check sum.
• Remedy: <User Check> • Install the latest firmware.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: E100
• Display: Print Unable E1 Turn the power off and then back on again.
• Description: Program error
• Remedy: <User Check> • Install the latest firmware.
  1 Main PCB failure Replace the main PCB ASSY.

• Code: E500
• Display: Print Unable E5 Turn the power off and then back on again.
• Description: An error occurred during access to the DRAM in the main PCB ASSY.
• Remedy: 1 Main PCB failure Replace the main PCB ASSY.

• Code: E600
• Display: Print Unable E6 Turn the power off and then back on again.
• Description: Write error in the EEPROM of the main PCB ASSY.
• Remedy: 1 Main PCB failure Replace the main PCB ASSY.

• Code: F900
• Display: Machine Error F9
• Description: The country code was not entered correctly.
• Remedy: 1 The power is turned OFF while function code 74 was running. Reenter the country code. 2 Main PCB failure Replace the main PCB ASSY.

– Get more error code list with quick guide to fix printer product, click here
– About get help with reseting Epson inkpad or others, click here

About Canon Servie Tool V5610

– Canon Service Tool V5610 is a tool used to perform maintenance on Canon printers and reset Canon printers after replacement of parts such as replacing ink absorbents, print heads, printer mainboard, and others. Based on the many cases we have encountered, the Service Tool is most often used to reset ink absorber counter value when the waste ink absorber is full.
– The ink absorber is going to be full of box, it has to be replaced or cleaned the waste ink absorber. Also, replaceing or cleaning the waste ink absorber, you need to repair or reset the waste ink counter value, cause those parts are concerned to each others.
– So using Canon Service Tool V5610 to reset the waste ink counter value becomes effective when the ink absorber is replaced or cleaned.

– Canon Service Tool V5610 can use to fix error code 5B00, 5B02, 5B04, 5B14, 1701, 1702, 1700 on your printer. You must enter Service Mode on your printer to use this Canon Service Tool.
– If the printer can not enter Service Mode, you can not reset it by Canon ST V5610. In this case, change EEPROM on the logic board.

Canon Service Tool V5610 Functions

– Fix Canon printer 7 times/ 8 times red light blinking:

– Fix Canon printer error code: 5B00, 5B01, 1700, 1701

Enter Service Mode on Canon Printer

1. Turn off a printer
2. Press and hold the Resume/Cancel/Stop button
3. Press and hold the ON button (do not release both buttons)
4. Release the Resume/Cancel/Stop button (do not release the ON button)
5. While holding the ON button, press the Resume/Cancel/Stop button 5 times, then release both the ON and Resume/Cancel/Stop buttons together.
– Canon printer in service mode: computer detects new hardware, led on printer goes green light.
For more information about Canon Serice Tool V5610

– Get more information about Epson XP 15000 troubleshooting, click here
– Buy cheap key of Epson WIC Reset Tool, CLICK HERE
– Key Epson Adjustment Program, CLICK HERE
https://dnasofts.com/download-epson-xp-6100-driver-firmware-and-manuals/

Contact us to get support with Brother DCP1612W Error case

Telegram: https://t.me/hyperaktiv
Facebook: https://www.facebook.com/dngnm/
Or click here to get more ways.

Source:
https://dnasofts.com
https://shop.nguyendangnam.com/